Jack, original

Any information on all other kit
Post Reply
Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Jack, original

Post by Fossibear » Sun Jan 05, 2020 6:27 pm

Hi,

my question is: did the Lightweight have as normal tool a jack on board and if yes, what did it look like?
I‘ve seen a pic where something like such a tool was put into the rear wheel arch box - was that normally so or has just someone done so?

Regards, Steve
It's supposed to look like that, it's crochet...

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Jack, original

Post by removeduser185 » Sun Jan 05, 2020 8:56 pm

Yes, it was part of the Complete Equipment Schedule (kit list) along with a wheel brace, a pair of 8" pliers, a screwdriver, an adjustable spanner and a tyre pressure gauge. Here is one for ale on eBay.
They rarely come up for sale with their handles, but, by chance, there is a handle on eBay as well.
If you are trying to keep the vehicle original then they are good to have, but, to use, they're a bit awkward so a good hydraulic bottle jack is easier and quicker to use - I have one from a Discovery or a Range ROver - still says Land Rover on the bottle so it's good enough.

Image
https://www.ebay.co.uk/itm/LAND-ROVER-S ... SwA2hdv1-D

Image
https://www.ebay.co.uk/itm/LAND-ROVER-S ... XQcVNQ69~h

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Jack, original

Post by Fossibear » Sun Jan 05, 2020 9:10 pm

Oouups - it looks a bit like coming directly from the Middle Ages :)

But, thanks Fred - now I know what I have to look for :D
It's supposed to look like that, it's crochet...

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: Jack, original

Post by Macvfork » Mon Jan 06, 2020 9:53 pm

Fred,
Do you know whether a Shelley jack LJ264 was also part of the 1/2t CES kit at some point perhaps prior to the one you indicate?
Hope so as donated a Shelley to someone here in the belief that model was the one.
Cheers
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Jack, original

Post by removeduser185 » Mon Jan 06, 2020 11:24 pm

Macvfork wrote: ↑
Mon Jan 06, 2020 9:53 pm
Fred,
Do you know whether a Shelley jack LJ264 was also part of the 1/2t CES kit at some point perhaps prior to the one you indicate?
Hope so as donated a Shelley to someone here in the belief that model was the one.
Cheers
Mac
Sorry Mac, I don't know. But, when vehicles weren't out on a detail, their CES would be put away in the stores. So, if there, were, say, 20 assorted Land Rovers in the unit, then there would be 20 jacks and 20 jack handles in the store. A driver taking a vehicle on a detail would simply be given the first one the storeman came to. I'm sure some jacks were marked as the one on eBay was with the intention of it being issued only to the particular vehicle, but I never came across that in my own experience, a jack was a jack was a jack and there were one or two different patterns among those on the shelves, though few of us knew who made them. I can't remember what other vehicles used the same jack as a Land Rover, I think Ferrets and four tonners used the next size up, (3 ton?) but can't remember quite now.

The CES entry simply specifies a "JACK screw hand 1 ton triple lift closed h 5 1/4 in open h 14in c/w 30in lg handle".

But... I have seen on this forum or that of HMVF at some time in recent years a thread on this very subject, so it might be worth doing a little digging.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: Jack, original

Post by Macvfork » Tue Jan 07, 2020 5:53 am

Thanks Fred. Will see how mine measure up to the spec you mention....
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Jack, original

Post by Fossibear » Tue Jan 07, 2020 7:08 pm

I‘d like to buy that thing but shipping to Germany does cost more than that item itself :cry:
But perhaps one day I‘ll find one on this side of the Channel...
It's supposed to look like that, it's crochet...

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Jack, original

Post by Fossibear » Fri Aug 06, 2021 3:35 pm

In between I’ve got a jack and I’ve got the handle but without the wooden pin.
Somewhere I’ve read that the metal part was stored under the bonnet but it seems to be a bit to long therefore. Can someone tell me please what the length of th metal rod should be?
The wooden handle I can make on my own (I learned carpenter some years ago)

Kindly regards, Steve
It's supposed to look like that, it's crochet...

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Jack, original

Post by removeduser185 » Fri Aug 06, 2021 4:54 pm

30 inches. See my post above! :D

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Jack, original

Post by Fossibear » Fri Aug 06, 2021 9:38 pm

Thanks a lot Fred - I couldn’t remember where I had read it

Kindly regards, Steve
It's supposed to look like that, it's crochet...

Post Reply