Jack, original
Jack, original
Hi,
my question is: did the Lightweight have as normal tool a jack on board and if yes, what did it look like?
I‘ve seen a pic where something like such a tool was put into the rear wheel arch box - was that normally so or has just someone done so?
Regards, Steve
my question is: did the Lightweight have as normal tool a jack on board and if yes, what did it look like?
I‘ve seen a pic where something like such a tool was put into the rear wheel arch box - was that normally so or has just someone done so?
Regards, Steve
It's supposed to look like that, it's crochet...
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: Jack, original
Yes, it was part of the Complete Equipment Schedule (kit list) along with a wheel brace, a pair of 8" pliers, a screwdriver, an adjustable spanner and a tyre pressure gauge. Here is one for ale on eBay.
They rarely come up for sale with their handles, but, by chance, there is a handle on eBay as well.
If you are trying to keep the vehicle original then they are good to have, but, to use, they're a bit awkward so a good hydraulic bottle jack is easier and quicker to use - I have one from a Discovery or a Range ROver - still says Land Rover on the bottle so it's good enough.

https://www.ebay.co.uk/itm/LAND-ROVER-S ... SwA2hdv1-D

https://www.ebay.co.uk/itm/LAND-ROVER-S ... XQcVNQ69~h
They rarely come up for sale with their handles, but, by chance, there is a handle on eBay as well.
If you are trying to keep the vehicle original then they are good to have, but, to use, they're a bit awkward so a good hydraulic bottle jack is easier and quicker to use - I have one from a Discovery or a Range ROver - still says Land Rover on the bottle so it's good enough.

https://www.ebay.co.uk/itm/LAND-ROVER-S ... SwA2hdv1-D

https://www.ebay.co.uk/itm/LAND-ROVER-S ... XQcVNQ69~h
Re: Jack, original
Oouups - it looks a bit like coming directly from the Middle Ages
But, thanks Fred - now I know what I have to look for
But, thanks Fred - now I know what I have to look for
It's supposed to look like that, it's crochet...
Re: Jack, original
Fred,
Do you know whether a Shelley jack LJ264 was also part of the 1/2t CES kit at some point perhaps prior to the one you indicate?
Hope so as donated a Shelley to someone here in the belief that model was the one.
Cheers
Mac
Do you know whether a Shelley jack LJ264 was also part of the 1/2t CES kit at some point perhaps prior to the one you indicate?
Hope so as donated a Shelley to someone here in the belief that model was the one.
Cheers
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: Jack, original
Sorry Mac, I don't know. But, when vehicles weren't out on a detail, their CES would be put away in the stores. So, if there, were, say, 20 assorted Land Rovers in the unit, then there would be 20 jacks and 20 jack handles in the store. A driver taking a vehicle on a detail would simply be given the first one the storeman came to. I'm sure some jacks were marked as the one on eBay was with the intention of it being issued only to the particular vehicle, but I never came across that in my own experience, a jack was a jack was a jack and there were one or two different patterns among those on the shelves, though few of us knew who made them. I can't remember what other vehicles used the same jack as a Land Rover, I think Ferrets and four tonners used the next size up, (3 ton?) but can't remember quite now.
The CES entry simply specifies a "JACK screw hand 1 ton triple lift closed h 5 1/4 in open h 14in c/w 30in lg handle".
But... I have seen on this forum or that of HMVF at some time in recent years a thread on this very subject, so it might be worth doing a little digging.
Re: Jack, original
Thanks Fred. Will see how mine measure up to the spec you mention....
Mac
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
Re: Jack, original
I‘d like to buy that thing but shipping to Germany does cost more than that item itself
But perhaps one day I‘ll find one on this side of the Channel...
But perhaps one day I‘ll find one on this side of the Channel...
It's supposed to look like that, it's crochet...
Re: Jack, original
In between I’ve got a jack and I’ve got the handle but without the wooden pin.
Somewhere I’ve read that the metal part was stored under the bonnet but it seems to be a bit to long therefore. Can someone tell me please what the length of th metal rod should be?
The wooden handle I can make on my own (I learned carpenter some years ago)
Kindly regards, Steve
Somewhere I’ve read that the metal part was stored under the bonnet but it seems to be a bit to long therefore. Can someone tell me please what the length of th metal rod should be?
The wooden handle I can make on my own (I learned carpenter some years ago)
Kindly regards, Steve
It's supposed to look like that, it's crochet...
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: Jack, original
30 inches. See my post above! 
Re: Jack, original
Thanks a lot Fred - I couldn’t remember where I had read it
Kindly regards, Steve
Kindly regards, Steve
It's supposed to look like that, it's crochet...