Monty the rather rusty 2A - 37FG31
Re: Monty the rather rusty 2A - 37FG31
Are the two top centre of the pic, the ones that hold the steering box stiffener bracket to the footwell?
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: Monty the rather rusty 2A - 37FG31
The two in the centre might be a bit large for the stiffener, hard to tell from the pic. The others look like the captive plates used to fit civi seat runners.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
You’ve helped me get there with some of them.. you’re right the centre top are too large bolts and too far apart to be for the stiffener. In fact the left hand ones fit that place perfectly. I had though until now that it was just nuts and bolts in that spot- makes so much more sense as captive bolts, given what a pain in the harris it was to reach around the footwell to hold a spanner on the nut while I socketed the other end. D’oh!
Slightly confused as to why I have five of them, but then some may have arrived in a previous job lot of parts I suppose - and may be unrelated to the lightweight.
Re: Monty the rather rusty 2A - 37FG31
I had a look through my list of parts I have bought, and I had made an annotation next to 330908 Boltplate, Stiffener, of 395064 and MRC5509. When I looked in the civi parts list they come up as used for both the stiffener and the front seat rails, with MRC5509 being the metric version.
I can't think of anywhere on the lightweight that uses a captive stud plate apart from on the steering box stiffener bracket.
Regards,
I can't think of anywhere on the lightweight that uses a captive stud plate apart from on the steering box stiffener bracket.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
So that’s it then - I must have just acquired them along the way at some point. Thanks Neil. At least I learned about the seat back and stiffener ones - and have also realised that I need to get two more of the upper tub mounting ones, as my old dog ears have the hole patten for them - the replacement panels just had the central bolt holes but not the holes for the two rivets. Good job I never throw anything away!AR4412 wrote: ↑Sun Jun 07, 2020 4:23 pmI had a look through my list of parts I have bought, and I had made an annotation next to 330908 Boltplate, Stiffener, of 395064 and MRC5509. When I looked in the civi parts list they come up as used for both the stiffener and the front seat rails, with MRC5509 being the metric version.
I can't think of anywhere on the lightweight that uses a captive stud plate apart from on the steering box stiffener bracket.
Regards,
Thanks again everyone - really helpful.
All the best,
Andy
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
The replacement door bottom arrived today. The fit is good, although the bulkhead needs to be pushed forward a fraction at the top, and the hinges could do with a bit of an adjust..
No one seems to have any near side doors at the moment, so maybe I’ll re-skin the old frame.. I have it clamped up in the garage awaiting a repair section being welded in. Will see what the weather is like tomorrow.
I also found the one remaining square tube bracket seatbelt mount thingy, and with the help of my trusty blowtorch, managed to remove the old eye bolt. The bolt is fubared, but the bracket just needed a couple of gouges welding up, and a soak in the derusting cauldron. I’ll give it a decent coat of zinc primer in the morning and will try to remember to order it a friend for the other side.
All the best,
Andy
All the best,
Andy
No one seems to have any near side doors at the moment, so maybe I’ll re-skin the old frame.. I have it clamped up in the garage awaiting a repair section being welded in. Will see what the weather is like tomorrow.
I also found the one remaining square tube bracket seatbelt mount thingy, and with the help of my trusty blowtorch, managed to remove the old eye bolt. The bolt is fubared, but the bracket just needed a couple of gouges welding up, and a soak in the derusting cauldron. I’ll give it a decent coat of zinc primer in the morning and will try to remember to order it a friend for the other side.
All the best,
Andy
All the best,
Andy
Re: Monty the rather rusty 2A - 37FG31
Hiya Andy!
,
Another piece of the puzzle slots into place mate.
Regards,
Another piece of the puzzle slots into place mate.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: Monty the rather rusty 2A - 37FG31
I made my own out of a piece of 1" square tube. I still have some left if you want to make one. You just need to weld in the lump of metal the eye-bolt is screwed into and that's easy enough. Will you be using your eye-bolts for the seatbelts? With the Series 3, the eye-bolts are there, but later seatbelts don't need them - they simply screw direct into the hole as there are no "D" shackles. So, if you need a pair, I can let you have mine.andrewjsimpson1977 wrote: ↑Mon Jun 08, 2020 7:08 pmsquare tube bracket seatbelt mount thingy, and with the help of my trusty blowtorch, managed to remove the old eye bolt. The bolt is fubared, but the bracket just needed a couple of gouges welding up, and a soak in the derusting cauldron. will try to remember to order it a friend for the other side.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
If you really don’t need them I would be grateful for them Fred - I currently have one, and am bidding on two more at the moment. Would be nice to get somewhere near a full set.Fred wrote: ↑Mon Jun 08, 2020 10:29 pmI made my own out of a piece of 1" square tube. I still have some left if you want to make one. You just need to weld in the lump of metal the eye-bolt is screwed into and that's easy enough. Will you be using your eye-bolts for the seatbelts? With the Series 3, the eye-bolts are there, but later seatbelts don't need them - they simply screw direct into the hole as there are no "D" shackles. So, if you need a pair, I can let you have mine.andrewjsimpson1977 wrote: ↑Mon Jun 08, 2020 7:08 pmsquare tube bracket seatbelt mount thingy, and with the help of my trusty blowtorch, managed to remove the old eye bolt. The bolt is fubared, but the bracket just needed a couple of gouges welding up, and a soak in the derusting cauldron. will try to remember to order it a friend for the other side.
Andy
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
..also like the square tube idea Fred - and agree it should be easy to zap one together. I’ve found my welding has improved a lot on smaller / finer parts by simply dropping down to 0.8 wire from the usual 0.9 - turns out (and it now seems obvious in hindsight) the thicker wire carries more current to the point of arc, and as such more heat and more blow-throughs.