Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Aug 14, 2019 7:50 pm

It’s been a fairly long day. After a night out seeing old mates in Manchester, and I have to admit, one too many scoops.. I walked into the hardest working day I’ve had in a long time. Still, there was just about time / energy left after work for a little spot of dash fascia and heater panel templating:

DD736245-65EA-4CCA-A3E3-2C84C8BAAB19.jpeg
DD736245-65EA-4CCA-A3E3-2C84C8BAAB19.jpeg (971.77 KiB) Viewed 2263 times

1609A315-B179-4CDF-9ADC-8C037C8A0326.jpeg
1609A315-B179-4CDF-9ADC-8C037C8A0326.jpeg (930.57 KiB) Viewed 2263 times

649D1D7D-0F94-4747-A897-4D15EF8A0632.jpeg
649D1D7D-0F94-4747-A897-4D15EF8A0632.jpeg (1.04 MiB) Viewed 2263 times

There are still a couple of measurements to check as I’m not convinced I have the steering column holes are quite right, and the lips I have allowed for the dash panel recesses may need adjusting a bit.

Hopefully tomorrow will see my new dremel arrive, and I can get on with chopping this thing up :) I do have a spare panel just in case, well ok WHEN I cock up the first one.

All the best,

Andy

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Wed Aug 14, 2019 9:05 pm

Which reminds me, I owe you some measurements. Tomorrow, promise!

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Aug 14, 2019 9:48 pm

Fred wrote: ↑
Wed Aug 14, 2019 9:05 pm
Which reminds me, I owe you some measurements. Tomorrow, promise!
No rush Fred, I’m in the office tomorrow so no playtime until the evening anyway.

Andy

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Fri Aug 16, 2019 9:13 pm

andrewjsimpson1977 wrote: ↑
Wed Aug 14, 2019 9:48 pm
Fred wrote: ↑
Wed Aug 14, 2019 9:05 pm
Which reminds me, I owe you some measurements. Tomorrow, promise!
No rush Fred, I’m in the office tomorrow so no playtime until the evening anyway.

Andy
Hi Andy,

Sorry, up to my eyes yesterday with the shepherd's hut - fitting the wiring. Blimey, it was hot in there. The insulation isn't in yet and the weather was hot and humid and under the wriggly tin roof - it was like a sauna. Nothing much achieved today, though, it piddled down all day. Anyway, it did mean I was able to go and look at the Land Rover quietly festering in the garage. The measurements for the steering wheel are as shown in the attached photo - centres to centre.
new bulkheadin primer small with dimensions.jpg
new bulkheadin primer small with dimensions.jpg (505.36 KiB) Viewed 2159 times
I do hope this helps.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Aug 17, 2019 7:35 am

Fred wrote: ↑
Fri Aug 16, 2019 9:13 pm
andrewjsimpson1977 wrote: ↑
Wed Aug 14, 2019 9:48 pm
Fred wrote: ↑
Wed Aug 14, 2019 9:05 pm
Which reminds me, I owe you some measurements. Tomorrow, promise!
No rush Fred, I’m in the office tomorrow so no playtime until the evening anyway.

Andy
Hi Andy,

Sorry, up to my eyes yesterday with the shepherd's hut - fitting the wiring. Blimey, it was hot in there. The insulation isn't in yet and the weather was hot and humid and under the wriggly tin roof - it was like a sauna. Nothing much achieved today, though, it piddled down all day. Anyway, it did mean I was able to go and look at the Land Rover quietly festering in the garage. The measurements for the steering wheel are as shown in the attached photo - centres to centre.
new bulkheadin primer small with dimensions.jpg

I do hope this helps.
Hi Fred :D absolutely perfect thanks matey. I managed to scavenge the other measurements from the pieces I cut out of the bulkhead so I’m pretty sure we’re good to go. Just need the dremel to arrive (it’s 2 days late and the more suspicious side of me suspects mail-related gremlins) and I can crack on - hopefully today maybe.

Glad to hear the Para-Recce-David-Cameron-Mobile-Reading-Room is coming along.. but where are our piccies?

All the best and thanks again for taking the time to check for me.

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Aug 17, 2019 6:44 pm

So my measurements were out, AND the panel was cut slightly too short. I don’t really want to check the order to see if the cock up was mine or the steel supplier’s. Whatever, I need the steel anyway. Thanks very much to Neil and Fred for supplying the measurements, and in two different denominations too. Inches or mms, my panel was never going to work so I ordered another. And a spare. And a rum.

Cheers! :!

Andy

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Sun Aug 18, 2019 10:05 am

Hiya Andy! :D ,

I was sorry to hear that you have had steel woes, and have been brought to a halt by them. :cry:

I reckon that your missing Dremel must be on the same delivery truck as my steel order, that was meant to be here Wednesday, but is so far a no show.

I have a bit of spare time for the project today, but no 3mm plate or 50mm angle, and it's p#####g down to brighten my mood.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Aug 18, 2019 11:08 am

AR4412 wrote: ↑
Sun Aug 18, 2019 10:05 am
Hiya Andy! :D ,

I was sorry to hear that you have had steel woes, and have been brought to a halt by them. :cry:

I reckon that your missing Dremel must be on the same delivery truck as my steel order, that was meant to be here Wednesday, but is so far a no show.

I have a bit of spare time for the project today, but no 3mm plate or 50mm angle, and it's p#####g down to brighten my mood.

Regards,
We have surely angered the restoration Gods buddy. I will prepare a ritual sacrifice of Battenberg. Given your disposition against the marzipan arts, I suggest maybe just having a beer and waiting for the storm to pass. We’ll get there. But when? I’ll leave such philosophical matters to wiser men.

Andy

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Sun Aug 18, 2019 11:31 am

Keep up the sacrifices mate, you've brought the sun out. (And it will get rid of more B#######g.)

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Aug 18, 2019 12:28 pm

:lol:

Post Reply