Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri Sep 27, 2019 7:16 pm

A bit of an update tonight as I’m busy over the weekend with various family duties..

Managed to strip the first door bottom:

2717C8D8-0C37-4B2E-BEE5-B4C80F90898D.jpeg
2717C8D8-0C37-4B2E-BEE5-B4C80F90898D.jpeg (976.29 KiB) Viewed 2410 times

The skin isn’t bad. Needs the bottom edge flap tidying up as it’s gone a bit wavy and thin in areas...but there’s plenty of thickness of the flap so I will trim off a mm or two and it should look nice and solid. There’s also a couple of dings to hammer out. Oh goody, more metalwork:

3974B514-C169-47E6-ACF4-C9651C36A73F.jpeg
3974B514-C169-47E6-ACF4-C9651C36A73F.jpeg (1.27 MiB) Viewed 2410 times

The frame suffers from the usual rot where water collects in the rear corner:

C5727F9E-C3C0-44C8-85BF-110EAD7D59BD.jpeg
C5727F9E-C3C0-44C8-85BF-110EAD7D59BD.jpeg (932.59 KiB) Viewed 2410 times

..buts that’s no problem because you can buy it by the metre:

4EC8D2F3-A7AE-4FCA-AA1E-E05EB6907A06.jpeg
4EC8D2F3-A7AE-4FCA-AA1E-E05EB6907A06.jpeg (740.61 KiB) Viewed 2410 times
I’ll try to get the jig made for the frame early next week, so I can cut out the rotten section and weld in new steel without it losing its shape. At least the old section is in one piece so I can use it as a template.

Hope you haven’t all given up on me.. I know it’s slow progress and I do like to waffle on..

All the best,

Andy

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Sat Sep 28, 2019 9:36 pm

andrewjsimpson1977 wrote: ↑
Fri Sep 27, 2019 7:16 pm
A bit of an update tonight as I’m busy over the weekend with various family duties..

Managed to strip the first door bottom:


2717C8D8-0C37-4B2E-BEE5-B4C80F90898D.jpeg


The skin isn’t bad. Needs the bottom edge flap tidying up as it’s gone a bit wavy and thin in areas...but there’s plenty of thickness of the flap so I will trim off a mm or two and it should look nice and solid. There’s also a couple of dings to hammer out. Oh goody, more metalwork:


3974B514-C169-47E6-ACF4-C9651C36A73F.jpeg


The frame suffers from the usual rot where water collects in the rear corner:


C5727F9E-C3C0-44C8-85BF-110EAD7D59BD.jpeg


..buts that’s no problem because you can buy it by the metre:


4EC8D2F3-A7AE-4FCA-AA1E-E05EB6907A06.jpeg

I’ll try to get the jig made for the frame early next week, so I can cut out the rotten section and weld in new steel without it losing its shape. At least the old section is in one piece so I can use it as a template.

Hope you haven’t all given up on me.. I know it’s slow progress and I do like to waffle on..

All the best,

Andy
Keep waffling on, since you’ve moved on to the door bottoms is the bulkhead finished ? ;-)
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Sep 28, 2019 9:51 pm

landylees wrote: ↑
Sat Sep 28, 2019 9:36 pm

Keep waffling on, since you’ve moved on to the door bottoms is the bulkhead finished ? ;-)
Er.. well... see... no. I have all the bits clamped up now, but I need someone to come round with their spot welder to stick it all together. I also have a bit more to do on the recesses, the new dremel cutting discs for which have now arrived. Maybe tomorrow (as the song goes..)

Andy

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sat Sep 28, 2019 10:43 pm

Yes, keep waffling on - we're all thoroughly enjoying your restoration and will really miss it when it is finished. Reminds me, I must update my Shepherds' hut thread! Plenty happened, but the weather... God, it's been awful. Showers, on average 5 minutes apart. Go outside, drag power tools out, line up work... starts to rain, go inside again!

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Sun Sep 29, 2019 2:47 pm

andrewjsimpson1977 wrote: ↑
Sat Sep 28, 2019 9:51 pm
landylees wrote: ↑
Sat Sep 28, 2019 9:36 pm

Keep waffling on, since you’ve moved on to the door bottoms is the bulkhead finished ? ;-)
Er.. well... see... no. I have all the bits clamped up now, but I need someone to come round with their spot welder to stick it all together. I also have a bit more to do on the recesses, the new dremel cutting discs for which have now arrived. Maybe tomorrow (as the song goes..)

Andy
Andy,
I could bring mine to Newbury but you would have to return it to Bishop’s Stortford in 1 or 2 weeks if that helps..it has a 30a plug on it now but should run off 13a...
Howard
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Sep 29, 2019 6:27 pm

landylees wrote: ↑
Sun Sep 29, 2019 2:47 pm
andrewjsimpson1977 wrote: ↑
Sat Sep 28, 2019 9:51 pm
landylees wrote: ↑
Sat Sep 28, 2019 9:36 pm

Keep waffling on, since you’ve moved on to the door bottoms is the bulkhead finished ? ;-)
Er.. well... see... no. I have all the bits clamped up now, but I need someone to come round with their spot welder to stick it all together. I also have a bit more to do on the recesses, the new dremel cutting discs for which have now arrived. Maybe tomorrow (as the song goes..)

Andy
Andy,
I could bring mine to Newbury but you would have to return it to Bishop’s Stortford in 1 or 2 weeks if that helps..it has a 30a plug on it now but should run off 13a...
Howard
That is an incredibly generous offer. Would be happy to return it within a week if you are sure you can spare it?

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Sun Sep 29, 2019 10:32 pm

andrewjsimpson1977 wrote: ↑
Sun Sep 29, 2019 6:27 pm
landylees wrote: ↑
Sun Sep 29, 2019 2:47 pm
andrewjsimpson1977 wrote: ↑
Sat Sep 28, 2019 9:51 pm
landylees wrote: ↑
Sat Sep 28, 2019 9:36 pm

Keep waffling on, since you’ve moved on to the door bottoms is the bulkhead finished ? ;-)
Er.. well... see... no. I have all the bits clamped up now, but I need someone to come round with their spot welder to stick it all together. I also have a bit more to do on the recesses, the new dremel cutting discs for which have now arrived. Maybe tomorrow (as the song goes..)

Andy
Andy,
I could bring mine to Newbury but you would have to return it to Bishop’s Stortford in 1 or 2 weeks if that helps..it has a 30a plug on it now but should run off 13a...
Howard
That is an incredibly generous offer. Would be happy to return it within a week if you are sure you can spare it?
I can manage without it for a week! I've still got to line up the bulkhead and doors before I spot weld the side panels.
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Mon Sep 30, 2019 2:42 pm

landylees wrote: ↑
Sun Sep 29, 2019 10:32 pm
andrewjsimpson1977 wrote: ↑
Sun Sep 29, 2019 6:27 pm
landylees wrote: ↑
Sun Sep 29, 2019 2:47 pm
andrewjsimpson1977 wrote: ↑
Sat Sep 28, 2019 9:51 pm
landylees wrote: ↑
Sat Sep 28, 2019 9:36 pm

Keep waffling on, since you’ve moved on to the door bottoms is the bulkhead finished ? ;-)
Er.. well... see... no. I have all the bits clamped up now, but I need someone to come round with their spot welder to stick it all together. I also have a bit more to do on the recesses, the new dremel cutting discs for which have now arrived. Maybe tomorrow (as the song goes..)

Andy
Andy,
I could bring mine to Newbury but you would have to return it to Bishop’s Stortford in 1 or 2 weeks if that helps..it has a 30a plug on it now but should run off 13a...
Howard
That is an incredibly generous offer. Would be happy to return it within a week if you are sure you can spare it?
I can manage without it for a week! I've still got to line up the bulkhead and doors before I spot weld the side panels.
You’re an officer and a gentleman, really appreciate that Howard.

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Wed Oct 02, 2019 10:53 pm

andrewjsimpson1977 wrote: ↑
Wed Sep 18, 2019 7:01 pm
landylees wrote: ↑
Tue Sep 17, 2019 10:56 pm
Fred wrote: ↑
Sun Sep 15, 2019 11:16 pm
andrewjsimpson1977 wrote: ↑
Sun Sep 15, 2019 10:35 pm

Fred - looking forward to perusing the stalls with you at Newbury :D
Yep, so am I!
i'm planning on being there too
Anything you’re short of mate that I might have? Shout out as I’m bringing a couple of bits for Fred and Richard anyway so it’s no hassle.
Only thing I really need is a decent left hand IIA wing. If I end up having one made it is likely to cost £300 + VAT so would consider paying similar for NOS (and no doubt hand delivered by the pied piper riding a Unicorn but I can dream)
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Oct 13, 2019 5:58 pm

Right, it’s been another crazy week - but conscious of the need to get cracking I found some time this evening to spot weld on the first couple of panels to the bulkhead.

BCAC5D92-0A3D-4B0C-9C74-16446F8BB95C.jpeg
BCAC5D92-0A3D-4B0C-9C74-16446F8BB95C.jpeg (835.67 KiB) Viewed 2096 times
A8AEA7EE-C1D9-4B31-A448-B8BB53C4A71B.jpeg
A8AEA7EE-C1D9-4B31-A448-B8BB53C4A71B.jpeg (893.46 KiB) Viewed 2096 times

Trying to hold the welder at the angles needed to get the fascia panel spotted to the goalpost is, to be totally honest...an absolute bitch of a job. I wouldn’t recommend it hungover. I have had a couple of minor blow throughs but nothing that can’t be fixed.

Huge thanks to Howard for the loan of his welder - promise I will get some more done tomorrow!

Best regards,

Andy

Post Reply