Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Sep 15, 2019 4:51 pm

Floor mounting tabs bent over:

FE751331-F01D-4A98-891D-12DFD0A6CC38.jpeg
FE751331-F01D-4A98-891D-12DFD0A6CC38.jpeg (1.95 MiB) Viewed 2570 times

899B34B1-0606-4678-A671-C8F7A5E2647C.jpeg
899B34B1-0606-4678-A671-C8F7A5E2647C.jpeg (1.28 MiB) Viewed 2570 times

Then spent ten minutes or so bending it over my knee, stopping to compare every now and then with the original:

3F43165F-25D1-4AD0-8EE0-1E8636AF2D4E.jpeg
3F43165F-25D1-4AD0-8EE0-1E8636AF2D4E.jpeg (955.75 KiB) Viewed 2570 times

..here’s a comparison with the real thing. The right hand curve needs work, as it starts too early - but otherwise it’s a pretty good match for the original. I should be able to finish it off tomorrow and get the panels clamped together. The acid test is when it mates up with the heater panel and the gearbox tunnel vanity end plate.

58CE443C-BFB9-4861-9DA4-1493D883AFF2.jpeg
58CE443C-BFB9-4861-9DA4-1493D883AFF2.jpeg (898.88 KiB) Viewed 2570 times

Off to walk the dog now so that’s it for today,

All the best,

Andy

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Sun Sep 15, 2019 7:16 pm

Hiya Andy! :D ,

Nice fabrication work going on there mate. 8-)

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sun Sep 15, 2019 9:37 pm

That's brilliant, mate. Really impressive and I can't wait to see it finished.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Sep 15, 2019 10:35 pm

Fred wrote: ↑
Sun Sep 15, 2019 9:37 pm
That's brilliant, mate. Really impressive and I can't wait to see it finished.
Thanks fellas, slow progress as always but I’ll get there.

Fred - looking forward to perusing the stalls with you at Newbury :D

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sun Sep 15, 2019 11:16 pm

andrewjsimpson1977 wrote: ↑
Sun Sep 15, 2019 10:35 pm

Fred - looking forward to perusing the stalls with you at Newbury :D
Yep, so am I!

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Tue Sep 17, 2019 10:56 pm

Fred wrote: ↑
Sun Sep 15, 2019 11:16 pm
andrewjsimpson1977 wrote: ↑
Sun Sep 15, 2019 10:35 pm

Fred - looking forward to perusing the stalls with you at Newbury :D
Yep, so am I!
i'm planning on being there too
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Sep 18, 2019 7:01 pm

landylees wrote: ↑
Tue Sep 17, 2019 10:56 pm
Fred wrote: ↑
Sun Sep 15, 2019 11:16 pm
andrewjsimpson1977 wrote: ↑
Sun Sep 15, 2019 10:35 pm

Fred - looking forward to perusing the stalls with you at Newbury :D
Yep, so am I!
i'm planning on being there too
Anything you’re short of mate that I might have? Shout out as I’m bringing a couple of bits for Fred and Richard anyway so it’s no hassle.

Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Re: Monty the rather rusty 2A - 37FG31

Post by Landie68 » Thu Sep 19, 2019 5:46 pm

Has 1 item for Andy for Newbury, and aim to bring along the other freebie bits we got, if nobody wants them, I am sure they will sell and I can donate to the club funds
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

User avatar
Sidders101
Bake Off Judge
Posts: 2406
Joined: Wed Apr 02, 2014 7:57 pm
Location: Winchester

Re: Monty the rather rusty 2A - 37FG31

Post by Sidders101 » Sun Sep 22, 2019 8:20 am

I will be there in the usual place offering a chair and MAYBE a cuppa...there will be shelter if its raining...very welcome to leave bits safely whilst hunting.
Sidders


1974 Series 3 LWT 12v RHD 69-FM-24 , Royal Marines ("Intrepid")
1976 101 forward control gun tractor 12v RHD- 73-FL-43 ex 1,2 & 3 Para ("Kryten")
1979 Sankey NT Trailer 06-HF-86 78 Engr Reg (Herman)
1978 Trophy Frank Spencer impression (1st place)

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Sep 22, 2019 3:28 pm

Sidders101 wrote: ↑
Sun Sep 22, 2019 8:20 am
I will be there in the usual place offering a chair and MAYBE a cuppa...there will be shelter if its raining...very welcome to leave bits safely whilst hunting.
Nice one Sid, looking forward to a brew and a natter.

So this week I’ve been pretty busy with work, and the weekend has been mostly spending time with the kids, but I did get in a little tinkering in here and there..

Lifted the tub back up to tap the new bolt holes to line up with the 2a-spec seat belt brackets:

E6210C13-71DD-49B5-B60D-2A849DCC43B0.jpeg
E6210C13-71DD-49B5-B60D-2A849DCC43B0.jpeg (764.5 KiB) Viewed 2368 times

I also offered up the passenger side sill. There is a blob of weld on the underside of the hinge panel stopping it from mating flush - this will get ground off when the bulkhead bits are welded together. As with the other side, adding the sill panel seems to vastly improve the whole look of the side of the truck:

105CDA97-264E-468B-94DE-A18AE8CB33F4.jpeg
105CDA97-264E-468B-94DE-A18AE8CB33F4.jpeg (926.29 KiB) Viewed 2368 times

I also started cutting out the two remaining recesses from the dashboard, but managed to chew up a couple of cutting discs and soon ran out completely. Annoying. Decided instead to test hang the various bits to see what needs fettling:

B1CE1C51-9801-49BE-8DF1-60BF80BFE2D6.jpeg
B1CE1C51-9801-49BE-8DF1-60BF80BFE2D6.jpeg (797.91 KiB) Viewed 2368 times
405074F0-7136-436C-97FC-F1D2D92563D5.jpeg
405074F0-7136-436C-97FC-F1D2D92563D5.jpeg (1.21 MiB) Viewed 2368 times

The new discs for the dremel should be here tomorrow, so hopefully I’ll find some time in the evening to finish the recesses and maybe cut out the hole for the steering column. Plan for next weekend is to finish any remaining tweaking of the constituent parts and maybe even get Tony in for welding duties.

That’s it for now,

Andy

Post Reply