Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Sun Jun 09, 2019 7:30 pm

Looking good!

You’ve earned a beer/cake or two for that fine show.
2A - 39 FG 70

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sun Jun 09, 2019 9:27 pm

That's certainly progress. It won't be long, now, before you have the body ready for spraying.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jun 09, 2019 9:53 pm

Thanks Chris, Neil i'm trying to keep the momentum going as long as it will.

Fred - I'll be on to the dreaded bulkhead o'doom after the seat box, so you'll have to give me a few weeks to get my head around that one... but then yes... green paint.

I dream of it.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu Jun 13, 2019 12:59 pm

The paint on the backing plates for the outer seat belt brackets has finally cured (what is going on with the weather?!?)

3E14D13F-A8C8-4648-975F-732E0A9EDED2.jpeg
3E14D13F-A8C8-4648-975F-732E0A9EDED2.jpeg (1.02 MiB) Viewed 2257 times

...so I managed to find some time over lunch to run out and bolt (but not rivet) them in place. This is just a test fit as it’ll all have to come off when I paint the tub. The brackets were also added allowing me to mark up the holes in the seat back for the eye bolts. The eye bolts I still haven’t got. Ebay why hath thou forsaken me!!!???

E462F21C-FB64-45D3-9192-A2C7FFA3BFFA.jpeg
E462F21C-FB64-45D3-9192-A2C7FFA3BFFA.jpeg (1.03 MiB) Viewed 2257 times
Tomorrow with any luck I’ll have time to fit the inner pair of brackets, and continue repairing the seat box. Progress is slow, but each bit done is coming off the list.

The massive, never ending list.

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Jun 15, 2019 4:57 pm

Today saw more work on the seat back panel and seat box. First the holes for the set belt brackets were elongated to allow for fitting them in the boggle-eyed 2a way. Y’know... like the big man (or woman) upstairs intended :D

98E7FE75-ADF4-4A27-8267-0BA15F01AB1F.jpeg
98E7FE75-ADF4-4A27-8267-0BA15F01AB1F.jpeg (827.32 KiB) Viewed 2200 times

Finger sander made the shape all nice:

685EDF14-56EA-4AA5-9A4D-550CEF6326CA.jpeg
685EDF14-56EA-4AA5-9A4D-550CEF6326CA.jpeg (900.89 KiB) Viewed 2200 times

..and the holes into the seat back panel were marked and drilled, allowing the centre brackets to be fitted. The chassis mounting brackets for these two inner points were drilled with two new 5mm holes, and fitted with some downsized bolts for now. They will need tapping to take the proper bolts but I’ll need to buy a tap first.

67F537ED-1C66-4E57-BE71-CAE7FACB8E92.jpeg
67F537ED-1C66-4E57-BE71-CAE7FACB8E92.jpeg (739.42 KiB) Viewed 2200 times

Might as well give the outer two brackets the same treatment:

8C0FFB55-1090-497D-AAED-DBBC2E50CAFA.jpeg
8C0FFB55-1090-497D-AAED-DBBC2E50CAFA.jpeg (993.66 KiB) Viewed 2200 times

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Jun 15, 2019 5:07 pm

More work on the seat box followed, which needed unwanted rivet holes filling, new ones drilling and general alignment and flexing into shape to meet the mounting holes in the chassis:

C9577BF5-9457-4C39-96F1-13B7AC3B525D.jpeg
C9577BF5-9457-4C39-96F1-13B7AC3B525D.jpeg (1010.25 KiB) Viewed 2200 times
C8717DDC-7733-48BB-A594-AAFA19F7568F.jpeg
C8717DDC-7733-48BB-A594-AAFA19F7568F.jpeg (1.01 MiB) Viewed 2200 times

And then it was finally time for me to have a go at sitting in the driver’s seat for the first time in four years. Ok there’s no wheel or pedals, but boy did I enjoy changing gears and imagining driving it out of the garage. I’d managed to forget about the incredibly upright driving position... how anyone ever drove these things over long distances I’ll never know.

09AA358A-4143-4584-9B5D-C65B3071EDCD.jpeg
09AA358A-4143-4584-9B5D-C65B3071EDCD.jpeg (1.11 MiB) Viewed 2200 times
I’m nearly out of excuses not to do the bulkhead.. just a bit more fettling of the seat box next time, and there are some locating tangs and other repairs needed on the lids.. but then.. oh god then.

That’s it for today, it’s beer o’clock.

Andy

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Sat Jun 15, 2019 9:28 pm

Hiya Andy! :D ,

Good to see you've achieved a bit more today. 8-) (It looks like my plans for tomorrow have been scuppered by a family birthday party, but as its for a five year old there should be jelly and cake. And if I'm sneaky, I might be able to make of with some of his Lego in revenge. :twisted: )

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu Jun 20, 2019 7:57 pm

Another couple of evenings and another grim job goes by. Front propshaft stripped, de gunged,de-rusted, and anti-rust-primered.

The UJs were fine, but in the way as I wanted to clean the props up, er...properly. And as I’d like this to last another 50 years, might as well replace the joints. Getting the old UJs out was the usual absolute sod of a job. A job that was made so much less enjoyable thanks to a combination of snapped circlips (Neil I now feel your pain), bearing end caps that needed driving out with a socket and hammer, and one that just wouldn’t budge, so was chopped through with assistance from my assistant, Mr A Grinder.

F4159E54-ACD7-4CFF-9DFB-7B6B62FC1D26.jpeg
F4159E54-ACD7-4CFF-9DFB-7B6B62FC1D26.jpeg (1.01 MiB) Viewed 2063 times

..and just for Fred here’s some evidence it was painted green:

76FC6393-CF9B-497F-8BC6-382F0BA97C58.jpeg
76FC6393-CF9B-497F-8BC6-382F0BA97C58.jpeg (1.19 MiB) Viewed 2063 times

In primer:

0B22661C-6D8D-4BE0-BF6C-D860732E1902.jpeg
0B22661C-6D8D-4BE0-BF6C-D860732E1902.jpeg (1.15 MiB) Viewed 2063 times

The cap was rescued but the seal is little more than a splodge. The split steel clip survived though, and I’ve read somewhere that it’s possible to use the felt wavy edged seals from civvy hubs to replace the old rubber ones. I have two in stock from a generic hub repair kit, so it’s worth a try.

75E6F9A0-E8B9-4714-A2BF-2D4EF47C7535.jpeg
75E6F9A0-E8B9-4714-A2BF-2D4EF47C7535.jpeg (993.59 KiB) Viewed 2063 times
The new UJs should arrive tomorrow, so hopefully after I get back from work I can get them fitted. I’ll also try to remember to pick up some green paint, and order a new pair of gaiters and jubilee clips.

The rear prop can wait for another time. It already 3 snapped circlips so I’m going to have to have a think about how best to strip it.


All the best,

Andy

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Thu Jun 20, 2019 8:44 pm

andrewjsimpson1977 wrote: ↑
Thu Jun 20, 2019 7:57 pm
....might as well replace the joints. Getting the old UJs out was the usual absolute sod of a job. A job that was made so much less enjoyable thanks to a combination of snapped circlips (Neil I now feel your pain), bearing end caps that needed driving out with a socket and hammer, and one that just wouldn’t budge, so was chopped through with assistance from my assistant, Mr A Grinder.
Hiya Andy! :D ,

So happy that someone else is suffering the woes of rusted away circlips. You could try smacking the bearing cup down hard, to release some of the pressure on the circlip, and if you can get behind the end of the circlip with a small seal pick tool, or a 1.5/2mm flat bladed screwdriver you may be able to pry/tap them out. Failing that, with a steady hand and a Dremel with a cutting disc aligned with the circlip groove, and aimed to grind away the middle section of the circlip, should allow you to free them as you will have two smaller bits you can tap out. Possibly.

If all else fails, you can pop over and borrow my plasma cutter.
andrewjsimpson1977 wrote: ↑
Thu Jun 20, 2019 7:57 pm
..and just for Fred here’s some evidence it was painted green:
Good to see another green propshaft out there. :D

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Thu Jun 20, 2019 9:12 pm

AR4412 wrote: ↑
Thu Jun 20, 2019 8:44 pm
andrewjsimpson1977 wrote: ↑
Thu Jun 20, 2019 7:57 pm
....might as well replace the joints. Getting the old UJs out was the usual absolute sod of a job. A job that was made so much less enjoyable thanks to a combination of snapped circlips (Neil I now feel your pain), bearing end caps that needed driving out with a socket and hammer, and one that just wouldn’t budge, so was chopped through with assistance from my assistant, Mr A Grinder.
Hiya Andy! :D ,

So happy that someone else is suffering the woes of rusted away circlips. You could try smacking the bearing cup down hard, to release some of the pressure on the circlip, and if you can get behind the end of the circlip with a small seal pick tool, or a 1.5/2mm flat bladed screwdriver you may be able to pry/tap them out. Failing that, with a steady hand and a Dremel with a cutting disc aligned with the circlip groove, and aimed to grind away the middle section of the circlip, should allow you to free them as you will have two smaller bits you can tap out. Possibly.

If all else fails, you can pop over and borrow my plasma cutter.
andrewjsimpson1977 wrote: ↑
Thu Jun 20, 2019 7:57 pm
..and just for Fred here’s some evidence it was painted green:
Good to see another green propshaft out there. :D

Regards,
I have the same problem....i have left mine rotting on the workshop floor in disgust
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

Post Reply