Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jul 07, 2019 8:08 pm

HAPPY PAGE 200!! :! :dbday: :D X!

So this weekend has been quite good to me, if not to Sara. We were supposed to be off doing stuff with the kids in London, but she has been down with some sort of bug all weekend, so I have been ‘forced’ to spend a couple of days tinkering in the garage while the kids sat on their iPads, slowly turning into Kevin and Perry.

Oh woe is me :D

First stop, the clutch tower holes where the shaft should go were welded where my over enthusiastic hacksaw had got a bit carried away:

C5A43B90-587E-4241-9847-15E521E6AE0D.jpeg
C5A43B90-587E-4241-9847-15E521E6AE0D.jpeg (843.5 KiB) Viewed 2208 times
The weld was then filed smooth ready to accept the new shaft when it arrives.

Next, the tower, pedal and related gubbins were put back in the deruster for 12 hours, zinc primed and painted. I even dug out the bean tin and its clamp (not shown) and gave them a fresh coat of paint, as the paint on the reservoir had suffered a reaction at some point and gone all orange-peely:

6F146D94-1765-4F10-AA8D-B64E0BF4A397.jpeg
6F146D94-1765-4F10-AA8D-B64E0BF4A397.jpeg (889.63 KiB) Viewed 2208 times

Please excuse the improvised ‘curing frames’ :roll:

D123C4E0-FEFD-4E12-92D3-D875320014C8.jpeg
D123C4E0-FEFD-4E12-92D3-D875320014C8.jpeg (876.9 KiB) Viewed 2208 times
BEDD0D1D-335D-464A-9743-66D3AE56EBCE.jpeg
BEDD0D1D-335D-464A-9743-66D3AE56EBCE.jpeg (1.02 MiB) Viewed 2208 times
Then it was on to the bulkhead...
Last edited by andrewjsimpson1977 on Sun Jul 07, 2019 8:48 pm, edited 5 times in total.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jul 07, 2019 8:17 pm

As there are two new inner footwell panels heading over to Simpson Towers in the post, I needed to prepare the remains of the bulkhead for their arrival.

First the old inner panels were chopped (keeping them aside as patterns for the various holes):

8572E468-87AD-4B63-8180-34F86D3F753C.jpeg
8572E468-87AD-4B63-8180-34F86D3F753C.jpeg (1.16 MiB) Viewed 2207 times

You can see a split in the lower flange to the left in this photo - this needed a zap with the MIG to make it strong enough to take the replacement panel when it arrives:

87ADD107-8210-461D-A502-9BC114F5E8A6.jpeg
87ADD107-8210-461D-A502-9BC114F5E8A6.jpeg (1.3 MiB) Viewed 2207 times

The wavy edges left where the side panels were deleted will be given a tickle with the hammer before fixing the new panels on. They’re not as bad as they look in the photos.

Then it was on to the curved skirt section, which was quite rippled and misshapen, and missing a foot. The idea is of course that it is re-shaped to match the vanity panel which joins the bulkhead and gearbox tunnel:

0F482BE5-8E36-4026-9A06-7D49EF6EA3EB.jpeg
0F482BE5-8E36-4026-9A06-7D49EF6EA3EB.jpeg (536.65 KiB) Viewed 2207 times
You can also see the beginnings of the facia repair in the photo above, which I have dusted over for now with zinc paint, but which definitely needs more grinding back, and in some areas more filling in with weld. The left hand side of the dash still needs more straightening too, but I'll sort all that out next week. I'll bang on about the dash repairs in more detail shortly, but first here is the new foot piece, cut and bashed into shape over the end of a pallet:

3546C26F-1A23-4069-A883-80F0D33A53F4.jpeg
3546C26F-1A23-4069-A883-80F0D33A53F4.jpeg (1001.63 KiB) Viewed 2207 times
Last edited by andrewjsimpson1977 on Sun Jul 07, 2019 9:18 pm, edited 9 times in total.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jul 07, 2019 8:33 pm

And here’s proof that the cover fits now the curved edge has been introduced to Mr and Mrs Hammer and Dolly:

91DACBDE-ECE7-45FA-A65E-0681C8DFDA73.jpeg
91DACBDE-ECE7-45FA-A65E-0681C8DFDA73.jpeg (916.3 KiB) Viewed 2204 times

In the photo below, to the right of the new foot, and just above it - you can see the flange I mentioned which connects to the inner side panel. It was cracked (almost completely off) but has now been welded back on, although I still need to grind off the excess weld:

4822BFEA-098D-496F-9C05-E4E3C86CA40A.jpeg
4822BFEA-098D-496F-9C05-E4E3C86CA40A.jpeg (1.32 MiB) Viewed 2204 times

Close up showing alignment. I’m happy with that:

B791F03A-48D8-48CE-8125-5AA435657528.jpeg
B791F03A-48D8-48CE-8125-5AA435657528.jpeg (522.73 KiB) Viewed 2204 times

As mentioned above, I also had many an hour playing with the bulkhead facia higher up, which for a few reasons needed to be repaired again. Firstly, I noticed a big crack in the leg on the passenger side near the top, so off came the repaired dash section, and a sizeable piece of the cabin side of the leg, and in went a repair piece. This was then ground down, a new dash repair section cut, bent and welded in, and plenty of swearing about it all. I’m not yet done filling in all the little pin holes and grinding back the welds, so no more piccies yet until I'm happy with it.

While I was at it I decided to redo the facia repair on the driver's side too, as I had never been all that happy with the repair cosmetically. The new one is much neater, and with some dressing of the welds and sanding it should be near invisible. I also began filling in the missing top middle strip of the dash facia, but again it’s not finished yet. It seems to take me hours to do this tedious spot-spot-spot welding, but the results will be worth it I’m sure.

That’s it for now, feels once again like not enough to show for hours and hours of work, but we’re getting there. At least now there are two lips for the top of the footwells to attach to, and clean metal for the side panels to be plug welded to. Hopefully the bulkhead will be a bulkhead shaped thing by next weekend.

Thanks for tolerating my meandering updates,

All the best,

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jul 09, 2019 4:36 pm

So today has been a mad dash to the finish all day, with various different projects all wanting some attention at work. I did however get chance to spend half an hour with a sandwich in one hand and some clamps in the other, as these bad boys arrived this morning:

843BCCBD-51F3-4E09-8F17-0A568A5BF38C.jpeg
843BCCBD-51F3-4E09-8F17-0A568A5BF38C.jpeg (1.4 MiB) Viewed 2103 times

The footwells butt up against the new dash fascia repairs nicely (I have tried to hide the dash weld along the edge of the dash box, so a mounting strip was removed from the box and will be replaced later). I also need to attach the mount for the voltage regulator which was kept back from the rotten old fascia panel:

9DDC18B3-0020-409C-ACCC-408869D5BA6C.jpeg
9DDC18B3-0020-409C-ACCC-408869D5BA6C.jpeg (841.06 KiB) Viewed 2103 times

The new inner panels are a great fit, despite being from a different manufacturer to the rest of the footwells and hinge panels:

3CC0303C-10F3-46DD-AA0C-CBE8A406DC2B.jpeg
3CC0303C-10F3-46DD-AA0C-CBE8A406DC2B.jpeg (887.34 KiB) Viewed 2103 times

Here is the bulkhead roughly clamped together. I still need to finish straightening the wavy edges of the heater panel, and that foot I made yesterday? Well I had to cut it off as now the footwells are in place I realised it is the wrong shape:

AAF9C0C5-400A-4F00-865E-93DE55467AA9.jpeg
AAF9C0C5-400A-4F00-865E-93DE55467AA9.jpeg (1.04 MiB) Viewed 2103 times

Hopefully tomorrow some more welding wire will arrive in the post as I have about six inches left on the reel. There’s plenty of weld-filling and grinding / sanding to do yet and I still need to make some L-shaped pieces to weld on where the legs meet the hinge panels. Really, really pleased to see it coming together though.

Andy

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: Monty the rather rusty 2A - 37FG31

Post by Macvfork » Tue Jul 09, 2019 6:58 pm

Great job there Andy. Well done.
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

User avatar
the landy man
Cake Guru
Posts: 3080
Joined: Wed Sep 28, 2011 1:00 pm
Location: BOGNOR REGIS

Re: Monty the rather rusty 2A - 37FG31

Post by the landy man » Tue Jul 09, 2019 7:20 pm

Fantastic work Andy 8-)
50 more pages and you've caught up with Neil :D,
..ROD..
Bognor Regis,West Sussex


1972 S3 LIGHTWEIGHT 53 AM 74,RAF GS .Waddington strike command
1979 LIGHTWEIGHT 10 GX 11,GS .Black watch 1st battalion
1964 SERIES 2A..
Sankey narrow track,29 EN 84
Sankey narrow track project.
1967 BSA b40 WD 350cc.
1957 Triumph 6T Thunderbird.

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Tue Jul 09, 2019 7:32 pm

I'd best pull my finger out of my orifice and do some project work.

Good to see you're tackling the bulkhead Andy, keep up the good work mate.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jul 09, 2019 7:54 pm

Thanks Mac, I've had a major word with myself recently regarding maintaining the momentum - trying to do something significant each week. It finally feels like I'm getting somewhere :D

Rod, not likely mate - the thing is, the man's a moving target. If I do another fifty, Neil will have done a hundred more, and I suspect by then, he'll be finished and driving round on top secret manoeuvres.

Neil - I sympathise buddy, I've had a quiet six months before I restarted recently, its hard enough doing my standard restoration and I don't have any special kit to fabricate from photos, memories and tales of old. Once you get the chassis blasted and into paint, it'l be Recce-shaped in no time. Of course, life does get in the way doesn't it..

Andy

User avatar
the landy man
Cake Guru
Posts: 3080
Joined: Wed Sep 28, 2011 1:00 pm
Location: BOGNOR REGIS

Re: Monty the rather rusty 2A - 37FG31

Post by the landy man » Tue Jul 09, 2019 8:02 pm

Andy,Neil's a moving target alright but I've found his weakness!!! Egg and bacon rolls stop him in his tracks,throw in a few Carlings and you've got him! :shock:
Sounds a bit rude but it's not supposed to be. :!
..ROD..
Bognor Regis,West Sussex


1972 S3 LIGHTWEIGHT 53 AM 74,RAF GS .Waddington strike command
1979 LIGHTWEIGHT 10 GX 11,GS .Black watch 1st battalion
1964 SERIES 2A..
Sankey narrow track,29 EN 84
Sankey narrow track project.
1967 BSA b40 WD 350cc.
1957 Triumph 6T Thunderbird.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jul 09, 2019 8:05 pm

the landy man wrote: ↑
Tue Jul 09, 2019 8:02 pm
Andy,Neil's a moving target alright but I've found his weakness!!! Egg and bacon rolls stop him in his tracks,throw in a few Carlings and you've got him! :shock:
Sounds a bit rude but it's not supposed to be. :!
:lol:

My weaknesses are cake and whisky, so I can respect that.

Post Reply