Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jun 04, 2019 8:11 pm

AR4412 wrote: ↑
Tue Jun 04, 2019 8:01 pm
Check out the fabricating skills on Andy. Nicely done there mate. 8-)

Regards,
Thanks Neil, that means a lot coming from the King of Fab mate :D . I do hate paying people to do what I can figure out for myself, and while I could have walked across the field to the fabricators behind our house, it was worth having a go using the time honoured 'smash it with a hammer' approach :lol:

I should have said, for Howard's sake, that the hammer I used has a square face, so even when you switch from the pointy end to the big end, you still have a hammer that produces straight edges. You can pick up a set of metalworking hammers for about 15 quid from Eblag or Amaz(ing how much packaging they use)on so if you don't have any, get some in, they are worth their weight in gold.

Also...I bought a 'shrinking' hammer a while back, which has become my favourite metalworking thing, after it single-handedly (ok with backup from Mr Blowtorch) saved my warped wing. Just...just get one.

Andy

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Tue Jun 04, 2019 8:27 pm

thanks Andy, I do have a set of body work hammmers and dollies - just not that experienced with them and wanted to see what could be achieved....i will give it a go at the weekend
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jun 04, 2019 10:24 pm

landylees wrote: ↑
Tue Jun 04, 2019 8:27 pm
thanks Andy, I do have a set of body work hammmers and dollies - just not that experienced with them and wanted to see what could be achieved....i will give it a go at the weekend
...or there's this https://www.ebay.co.uk/itm/Land-Rover-S ... SwLdVcrcyO

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Tue Jun 04, 2019 11:06 pm

Yes but I’d rather have a go myself first, knowing that I can always pay again when/if I mess it up!
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jun 04, 2019 11:13 pm

landylees wrote: ↑
Tue Jun 04, 2019 11:06 pm
Yes but I’d rather have a go myself first, knowing that I can always pay again when/if I mess it up!
..exactly my view on these things. The 'that guy has one for sale' option is my safety net..nothing to lose by trying.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri Jun 07, 2019 7:03 pm

A couple of bits from this evening’s tinkerage..

First, lining up the position for the seat box rail:

4E791A13-9BF4-4A6C-9AC3-0E6102C10B0B.jpeg
4E791A13-9BF4-4A6C-9AC3-0E6102C10B0B.jpeg (2.63 MiB) Viewed 2157 times

Holes drilled:

7BA651D1-2DF1-4D61-8C76-835921AC239F.jpeg
7BA651D1-2DF1-4D61-8C76-835921AC239F.jpeg (2.77 MiB) Viewed 2157 times

Rail fitted:

272FD18A-E362-4C9E-BA9F-877D7BA7B506.jpeg
272FD18A-E362-4C9E-BA9F-877D7BA7B506.jpeg (2.56 MiB) Viewed 2157 times

Seat box main frame fitted (repairs still needed):

8462791F-9CC9-4339-9CA4-45EBDE653520.jpeg
8462791F-9CC9-4339-9CA4-45EBDE653520.jpeg (2.68 MiB) Viewed 2157 times
Last edited by andrewjsimpson1977 on Fri Jun 07, 2019 7:18 pm, edited 1 time in total.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri Jun 07, 2019 7:09 pm

I also recovered the seat belt anchor point reinforcements from the old valance panel. One bolt sheared, so will have to be drilled / wound out tomorrow. Why in seven hells did they decide to use domed slot headed machine screws in the place where the most corrosion is going to happen?

EAC0A3C8-1BE3-4A67-91AD-28A0ADDFEAC9.jpeg
EAC0A3C8-1BE3-4A67-91AD-28A0ADDFEAC9.jpeg (2.09 MiB) Viewed 2154 times

Will replace with the same type but high tensile zinc plated, and a layer of isolation material between the steel plate and the ally panel.

That’s it for today - I did want to have a go at repairing some holes in the ally seat box bits with lumiweld as I’ve found some videos online which told me I did it all wrong last time around. Unfortunately my blow torch ran out of propane almost immediately, so that job can wait for tomorrow.


That’s it for now,

All the best,

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jun 09, 2019 4:41 pm

Finally managed to push the landy outside so I could continue the big sort out of the garages / have a sweep out etc. Boring and tiring. So first a nice easy job before the hours of sorting and cleaning.. I drilled the seat back for the rifle clip brackets:

AE85CC69-BD7B-45C5-8A4C-970512334721.jpeg
AE85CC69-BD7B-45C5-8A4C-970512334721.jpeg (667.06 KiB) Viewed 2070 times

The sharp eyed will notice I have fitted both of the brackets types (front and back) rather than just the rear ones as would have been period correct. Logic is that they use the same holes, so the additional ones could always be removed later.. but for now they add some extra strength so I think i’ll leave them where they are.

With the truck outside I wanted to line up the floor panels, to make sure when I refit the seat box supports that they are fixed at the right width. This led to an impromptu mock-up session. Who doesn’t like one of those, eh?

21C28ABD-7A35-4B42-92AD-D19BD6E030CC.jpeg
21C28ABD-7A35-4B42-92AD-D19BD6E030CC.jpeg (1.08 MiB) Viewed 2070 times
27967D1F-234D-4C88-A904-4A93F23C0708.jpeg
27967D1F-234D-4C88-A904-4A93F23C0708.jpeg (1.18 MiB) Viewed 2070 times
6CC30933-F954-46A2-8295-2550325A1E49.jpeg
6CC30933-F954-46A2-8295-2550325A1E49.jpeg (1.18 MiB) Viewed 2070 times

A bit more to follow later when paint dries on the seat belt bits.

Andy

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: Monty the rather rusty 2A - 37FG31

Post by Loulou » Sun Jun 09, 2019 5:00 pm

I imagine it's a great moment of satisfaction that this garage release "by hand"; it erases all moments of doubt or impatience

Looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Sun Jun 09, 2019 6:23 pm

Hiya Andy! :D ,

Good to see you're getting a little bit more done this weekend.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

Post Reply