23HF14
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: 23HF14
Many thanks for that Clive, as Mac says, that's a useful reminder. But, yes, it is a new tab washer, folded both ways and, actually, it is flush with the nut - it is the shadow playing tricks. I had a bit of a job with it, actually, getting the end float right. Every time I got the end float correct on the inner nut, I put the adjusting nut on and it tightened the whole thing. But, I got there in the end. The tab washer idea isn't brilliant, though as, of course, once in place, you can't see the flats of the inner nut so have to guestimate and hope that tightening it off-centre won't move the nut - very little movement is needed to upset the end float. I am also bothered by the stub-axle to axle-casing bolts being secure. I read recently about a Range ROver driver whose bolts had come undone and his axle was held on by a single remaining bolt!
Anyway off the National Botanical Gardens now for the antiques fair. See you there?
Best
Fred
Anyway off the National Botanical Gardens now for the antiques fair. See you there?
Best
Fred
- fv1620
- Bake Off Judge
- Posts: 2268
- Joined: Thu Oct 06, 2011 2:16 pm
- Location: GB-CMN (formerly UK91)
- Contact:
Re: 23HF14
Yes & few glasses of cider & posting late at night. When I looked this morning it looked much better! The hazards of late night posting, sorry.
I'm putting the rear of the Wolf back together today & Tina has gone horsing although she belongs to that garden. I know, you want to be on Bargain Hunt that is being filmed there I believe & remember "No talking to the Reds" which seems good advice!
Clive Elliott
Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.
Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: 23HF14
A little something to hopefully put a smile on Fred's face..
The second photo shows the tag and recon date (I think)
Also got a nice few photos of a Land Rover field ambulance when I went to get the diff - it's one of the ones off EMLRA (Jack Hollingsworth). I won't post them here in the public area, but will put them up elsewhere later.
Andy
The second photo shows the tag and recon date (I think)
Also got a nice few photos of a Land Rover field ambulance when I went to get the diff - it's one of the ones off EMLRA (Jack Hollingsworth). I won't post them here in the public area, but will put them up elsewhere later.
Andy
Re: 23HF14
It brought a smile to my face, even though it's not mine and I don't need it. I think I may have unresolved diff issues from my childhood.andrewjsimpson1977 wrote: ↑Tue Apr 25, 2017 6:50 pmA little something to hopefully put a smile on Fred's face..
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: 23HF14
It is indeed a sight to behold! I'm very pleased and it was a good price. So, the next step will be to see how far west it can get using the "Forum Freighters". If anyone is coming this way (I'll be very surprised), and are likely to be seeing Andy, please bring it along with you.
Had a short time in the garage today. Trouble is, my garage is close to the front gate and, being in a village, lots of people stop and chat, so I lost an hour looking at someone's holiday snaps this morning. Still, it meant I was in drinking tea when the cold front came across with its sleet! But, later, I did a bit more cleaning off, de-rusting and prepared the second wheel for painting. Getting there!
Best to all and a BIG thank you to Andy for collecting the diff. You're a star!
Fred
Had a short time in the garage today. Trouble is, my garage is close to the front gate and, being in a village, lots of people stop and chat, so I lost an hour looking at someone's holiday snaps this morning. Still, it meant I was in drinking tea when the cold front came across with its sleet! But, later, I did a bit more cleaning off, de-rusting and prepared the second wheel for painting. Getting there!
Best to all and a BIG thank you to Andy for collecting the diff. You're a star!
Fred
Re: 23HF14
Hi Fred,
Where are you? I'm not far from Andy and i'm heading to Tenby at the end of May so i could drop it off somewhere on route if that helps?
Regards,
Neil
Where are you? I'm not far from Andy and i'm heading to Tenby at the end of May so i could drop it off somewhere on route if that helps?
Regards,
Neil
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: 23HF14
Aha! Bedford Neil #2 enters the fray!
Champion offer to help there matey - I had forgotten you were local - would be happy to drop the diff off with you if your proposal works for Fred.
...Fred?
Champion offer to help there matey - I had forgotten you were local - would be happy to drop the diff off with you if your proposal works for Fred.
...Fred?
Re: 23HF14
If onward movement can be arranged from the Overlord show, Clive?, I am willing to take it down there.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: 23HF14
Very many thanks to you, too, Neil. I have had a word with Clive and, yes, he'd be happy to take it off you and bear it back to the Principality. - With only slightly less ceremony than the return of the Stone of Scone to Scotland!
Can't wait to get it - I'm not tightening my U bolts until it is fitted as I don't think the axle casing will lie as level in the springs without it.
But, a little more achieved over the past few days.
I finally managed to separate the inlet and exhaust manifold. Took a really long time and I was really pleased that everything came apart OK in the end, though the studs were a bit thin. So, my neighbour comes round and lends me his stud remover - so what happens, yep, one stub snaps off!
No problem, I use a 3.5mm drill down the centre of the stud, perfect. Go to widen the hole with a 4mm one and, for some bizarre reason, smoke emerges and the end of the (clearly cheap) drill bit melts off into the end of the stud. So that's that then, 'cos when it hardened there was no way I could drill it out. New exhaust manifold required. Annoying as I had been so careful.
But, I now have two wheels painted and the two rear brake pipes fitted so, as work continues on the front axle, I shall also fit the fuel tanks and other bits at the back of the chassis. And a large order in with Paddocks and Craddocks for the front seals and bits and pieces I need, including TREs and, best of all, a new exhaust system - pleased to be fitting that as it is a bit of a milestone as the old one was blown. I have ordered a mild steel one, simply because the engine tone will be as original and, actually, at £35 I can afford to replace it again a few times if I need to. - And it is what was on there originally. I know some will regard that as heresy given that SS ones are so easily fitted and last forever. But then I have few "blue box bits as well which wouldn't meet with universal approval!
Fred
Can't wait to get it - I'm not tightening my U bolts until it is fitted as I don't think the axle casing will lie as level in the springs without it.
But, a little more achieved over the past few days.
I finally managed to separate the inlet and exhaust manifold. Took a really long time and I was really pleased that everything came apart OK in the end, though the studs were a bit thin. So, my neighbour comes round and lends me his stud remover - so what happens, yep, one stub snaps off!
No problem, I use a 3.5mm drill down the centre of the stud, perfect. Go to widen the hole with a 4mm one and, for some bizarre reason, smoke emerges and the end of the (clearly cheap) drill bit melts off into the end of the stud. So that's that then, 'cos when it hardened there was no way I could drill it out. New exhaust manifold required. Annoying as I had been so careful.
But, I now have two wheels painted and the two rear brake pipes fitted so, as work continues on the front axle, I shall also fit the fuel tanks and other bits at the back of the chassis. And a large order in with Paddocks and Craddocks for the front seals and bits and pieces I need, including TREs and, best of all, a new exhaust system - pleased to be fitting that as it is a bit of a milestone as the old one was blown. I have ordered a mild steel one, simply because the engine tone will be as original and, actually, at £35 I can afford to replace it again a few times if I need to. - And it is what was on there originally. I know some will regard that as heresy given that SS ones are so easily fitted and last forever. But then I have few "blue box bits as well which wouldn't meet with universal approval!
Fred