Any Land Rover related info can be posted here.
-
StuWright
- Master Baker
- Posts: 1740
- Joined: Wed Feb 24, 2016 11:10 pm
- Location: Southampton
Post
by StuWright » Sat Oct 01, 2016 11:39 pm
Ok for the moment I am going to stick to fitting the original seat belts and look at inertia if we ever get hold of the correct LR frames.
Before stripping I had a load of make shift reinforcing plates with o rings and climbing shackles. Not good and certainly not safe. I have looked on the parts disc but was unable to see any part numbers.
Does anyone know what I should have seatbelt wise in a 1972 GS and is there a list of fittings so I can just go buy them? Due to time I can't wait around for bits to come up on ebay as I need to work these out in the next week. Thanks in advance for any replies.

Thanks
Stu
55AM52 Ex RAF Land Rover Lightweight GS
-
StuWright
- Master Baker
- Posts: 1740
- Joined: Wed Feb 24, 2016 11:10 pm
- Location: Southampton
Post
by StuWright » Sun Oct 02, 2016 8:27 am
Thanks Fred.

Thanks
Stu
55AM52 Ex RAF Land Rover Lightweight GS
-
andracav
- Posts: 44
- Joined: Tue Sep 18, 2012 4:41 pm
- Location: Bergamo-Italy
Post
by andracav » Tue Oct 04, 2016 4:35 pm
I need same informations, please
Thanks
Regards
Andrea
@ndracav
30FK91
-
Sidders101
- Bake Off Judge
- Posts: 2406
- Joined: Wed Apr 02, 2014 7:57 pm
- Location: Winchester
Post
by Sidders101 » Tue Oct 04, 2016 4:42 pm
Britax clunk click beautiful brushed chrome classic lumps of machined perfection.....a pain to use but correct for year..expensive to buy...hard to find....reproductions common but still not cheap....personally I'm not fussy about belts..as long as they've got British standard numbers on them they will do...I use static belts...3 point anchor..so easy to fit and can tuck away for display...lap belt for centre.
I can't remember when the inertia belt rear bulkhead framework was introduced in the LWT...so over to you lot.
Sidders
1974 Series 3 LWT 12v RHD 69-FM-24 , Royal Marines ("Intrepid")
1976 101 forward control gun tractor 12v RHD- 73-FL-43 ex 1,2 & 3 Para ("Kryten")
1979 Sankey NT Trailer 06-HF-86 78 Engr Reg (Herman)
1978 Trophy Frank Spencer impression (1st place)
-
removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Post
by removeduser185 » Tue Oct 04, 2016 6:51 pm
andracav wrote:I need same informations, please
Thanks
Regards
Andrea
As Sidders has said, up until around 1980 the Lightweight had static belts. I understand that Britax were the original suppliers. At first, the straps were just that - only straps, later, as with all cars, the short strap was replaced with a stalk to enable them to be done up with one hand. Whether there was ever a lap belt fitted as standard for the centre passenger I don't know, but, I presume there was later on to keep in step with British and European law. Again, as Sidders says, original seatbelts are all but unobtainable, except repro ones through specialist classic car arts suppliers. And they are very expensive.
Fred
-
StuWright
- Master Baker
- Posts: 1740
- Joined: Wed Feb 24, 2016 11:10 pm
- Location: Southampton
Post
by StuWright » Tue Oct 04, 2016 8:59 pm
Fred wrote:andracav wrote:I need same informations, please
Thanks
Regards
Andrea
As Sidders has said, up until around 1980 the Lightweight had static belts. I understand that Britax were the original suppliers. At first, the straps were just that - only straps, later, as with all cars, the short strap was replaced with a stalk to enable them to be done up with one hand. Whether there was ever a lap belt fitted as standard for the centre passenger I don't know, but, I presume there was later on to keep in step with British and European law. Again, as Sidders says, original seatbelts are all but unobtainable, except repro ones through specialist classic car arts suppliers. And they are very expensive.
Fred
Anyone know where I could get repro ones from before I go down the Exmoor trim route?
Thanks
Stu
55AM52 Ex RAF Land Rover Lightweight GS
-
removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Post
by removeduser185 » Tue Oct 04, 2016 9:26 pm
http://www.johnrichardssurplus.co.uk/me ... 041_14.jpg This is what you are looking for. He's out of stock with the light grey ones, though has dark and they're a bit expensive. But knowing what you're after you can google images and chase up anything which looks close. Holdens and other classic car specialists may also be source.
Fred
-
andracav
- Posts: 44
- Joined: Tue Sep 18, 2012 4:41 pm
- Location: Bergamo-Italy
Post
by andracav » Wed Oct 05, 2016 10:22 am
Thanks to all answers!
Andrea
@ndracav
30FK91
-
Jiml
- Pastry Chef
- Posts: 644
- Joined: Sat Jul 18, 2015 1:56 pm
- Location: Burnley Lancashire
-
Contact:
Post
by Jiml » Wed Oct 05, 2016 12:14 pm
Failing all of the above a visit to a scrap yard might possibly yield results, I have access to an old series ambulance and there were still lap seat belts fitted, not sure of condition but I can go take a look if you like.
52HG42 my current love interest