Drivers side footwell replacement

If you have encountered or solved a problem post here
Post Reply
Devon13
Posts: 13
Joined: Sat Oct 26, 2024 1:44 am

Drivers side footwell replacement

Post by Devon13 » Sat May 03, 2025 4:00 pm

Hello there, have to replace the footwell which was unexpected to say the least. I have removed most items apart from a few things on the left hand panel. Having trouble finding the spot welds on the left to take it out completely and thinking rather than install the complete foot well to cut around the the rot on the left side and , cut out appropriately from the new one and slightly over lap? Any thoughts please. I can’t weld so either need to pop rivet it or get someone to come and weld it.
Attachments
IMG_5611.jpeg
IMG_5611.jpeg (3.31 MiB) Viewed 3282 times
IMG_5596.jpeg
IMG_5596.jpeg (1.94 MiB) Viewed 3282 times
09GT01 s111 1979 12v Ex - 30 Sig Regt / 21 Sig Regt / 31 Sig Regt (v) / 39 Sig Regt (v)
Mark

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Drivers side footwell replacement

Post by AR4412 » Sat May 03, 2025 9:00 pm

Hi Mark,

The spotwelds can be hard to see as they can be faint, and depending on the layers of paint on the bulkhead, almost invisible. I attacked mine with paint stripper and a wire wheel in a drill to reveal them so that they could be drilled out. Although I only replaced the toe boards and the hinge panels, not the inner firewall panel as fitted to the footwell you have purchased.

Hopefully these pics will help a bit.

This first one shows where all the spotweld were on the outside of the toe board to hinge panel. Although this is the passenger side it is just a mirror of the driver's side. The red line shows where a seam weld is that will need to be cut through to release the panel. This seam weld also extends over the hinge panel.
SAM_1655.JPG
SAM_1655.JPG (60.13 KiB) Viewed 3274 times
There is the same seam welding on the bottom of the panel holding it to the main bulkhead channel and hinge panel.
SAM_1806.JPG
SAM_1806.JPG (53.12 KiB) Viewed 3274 times
In this picture below, the red line shows where you will find a row of approximately 14 spotwelds all spaced roughly 30-35mm apart. The yellow line shows a row of 7 spotweld in the front of the panel. Spacings are the same. The green line a row of five spotwelds on the inner face of the gearbox tunnel panel. Again, spacings are the same.
SAM_1678.JPG
SAM_1678.JPG (64.91 KiB) Viewed 3274 times
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

Devon13
Posts: 13
Joined: Sat Oct 26, 2024 1:44 am

Re: Drivers side footwell replacement

Post by Devon13 » Sat May 03, 2025 10:25 pm

Thank you Neil, that’s a great help
09GT01 s111 1979 12v Ex - 30 Sig Regt / 21 Sig Regt / 31 Sig Regt (v) / 39 Sig Regt (v)
Mark

Post Reply