I have my bulkhead off and the floor panels roughly cut out. If you drill out the spot welds does it make it easier to remove the remainder of the floor panels and weld in the new ones?
Any tips on repairing the bulkhead appreciated, still have the chassis bolt stuck on the Lh side lol
Repairing the bulkhead
Re: Repairing the bulkhead
I used an aptly named 'spot weld drill bit' to drill out all the welds, then split the panels where still attached by bits of weld with a hammer and a paint scraper. Drilling out the spot welds allows you to puddle weld the new panels in place using the original weld positions. Prime once welded and then seam seal the edges to keep the water out.
When it comes to welding in the new panels, make sure the hole centres on the bulkhead legs are the same as those in the chassis just in case the legs have moved once the footwell panels were removed and any stresses relieved. Have a trial fit of the panels before tacking them in place, I had to slightly trim the outer edge of the footwell panels on mine to make everything align correctly. Use plenty of clamps to hold everything in place.
The remnants of the bolt might need the use of penetrating oil/freeze spray, heat and violence to get it out.
Regards,
When it comes to welding in the new panels, make sure the hole centres on the bulkhead legs are the same as those in the chassis just in case the legs have moved once the footwell panels were removed and any stresses relieved. Have a trial fit of the panels before tacking them in place, I had to slightly trim the outer edge of the footwell panels on mine to make everything align correctly. Use plenty of clamps to hold everything in place.
The remnants of the bolt might need the use of penetrating oil/freeze spray, heat and violence to get it out.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
AlbertaBoy
- Posts: 30
- Joined: Tue Jul 12, 2022 5:42 am
Re: Repairing the bulkhead
Thanks will look for the drill and get more clamps
Re: Repairing the bulkhead
Hi, it might also be worth investing in a set of cleco pins to help fit your new panels as they can be used in areas where clamps can't get to. I found them very useful when I did my footwells.
Cheers
Steve
Cheers
Steve
57 KB 58 1983 SIII GS Lightweight
Re: Repairing the bulkhead
Second vote for Cleco Pins and the clamps - absolutely brilliant.
Re: Repairing the bulkhead
Hi,
When you make the sealing of the various sheets in relation to each other, it is essential to use a polyurethane mastic and not a silicone mastic: the primer and the paint do not adhere or hardly adhere to the silicone mastic...
Regards.
Looloo
When you make the sealing of the various sheets in relation to each other, it is essential to use a polyurethane mastic and not a silicone mastic: the primer and the paint do not adhere or hardly adhere to the silicone mastic...
Regards.
Looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)