Lightweight starting handle??

Any Land Rover related info can be posted here.
Botsie
Posts: 46
Joined: Thu Oct 03, 2019 5:49 pm

Lightweight starting handle??

Post by Botsie » Sun Sep 26, 2021 12:51 pm

Just got back into Lwt ownership with a 1973 SIII which seems basically sound in its underpinnings and mechanics but needs much tidying. It is missing its starting handle - are these just a standard civvy type? Also through its 50 years of work, it has accumulated a fine selection of holes drilled in the tub , wings etc, for purposes long forgotten. What is the best/easiest way to seal these up? My natural inclination is to whack a fibreglass matt patch on the hidden side and then apply filler on the good side? Or?? The panels are straight and sound so not replacing them.Unfortunately it is also missing its complete door check assembly on both sides and it seems like the tubular door check assemblies that screw to the door are hard to get. :cry:

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: Lightweight starting handle??

Post by Loulou » Sun Sep 26, 2021 3:17 pm

Hello,

For the multiple holes in the tub and other bodywork elements, it is preferable to eliminate them by plugging them with a nice aluminum weld.

It is long, complicated and expensive to find a good aluminum welder but then you will have royal peace at this level.

Plugging with fiberglass risks cracking or peeling off afterwards (difference in material + difference in expansion + problems; see also twisting of the sheets, etc.) you will then have to start everything over as well as a new paint.

Regards.
Looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Lightweight starting handle??

Post by landylees » Sun Sep 26, 2021 8:51 pm

Lightweight starting handles are not standard, they are a different length. I can measure one of mine if you need to know the length
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Lightweight starting handle??

Post by removeduser185 » Sun Sep 26, 2021 9:45 pm

landylees wrote: ↑
Sun Sep 26, 2021 8:51 pm
Lightweight starting handles are not standard, they are a different length. I can measure one of mine if you need to know the length
I remember having this conversation before. I thought that, in fact, the Lightweight did use a standard length starting handle, but that there was a longer one which was needed if a bumper-mounted towhook was fitted. Certainly, that made sense, as the actual distance from the front of the engine to the outside of the bumper must be pretty similar for all Series Land Rovers. As I say, though, this is only my recollection.

Botsie
Posts: 46
Joined: Thu Oct 03, 2019 5:49 pm

Re: Lightweight starting handle??

Post by Botsie » Mon Sep 27, 2021 3:24 pm

landylees wrote: ↑
Sun Sep 26, 2021 8:51 pm
Lightweight starting handles are not standard, they are a different length. I can measure one of mine if you need to know the length
Yes, please! Thanks.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: Lightweight starting handle??

Post by weetchus » Mon Sep 27, 2021 6:43 pm

I just finished making a second starter handle yesterday as the first was a bit too long in the bend.
I can take a pic later and share with you. I actually used 3/4" steel bar and did two partial 'V' cuts where I wanted the bends (leaving 1/4" uncut)... then bent the shape and welded up the cracks/remaining holes.
I then just rounded the end that goes into the starter dog nut and drilled a 1/4 inch hole through the shaft end to line up where the tiny "T' bar makes contact with the groves in the starter dog nut.
Botsie wrote: ↑
Mon Sep 27, 2021 3:24 pm
landylees wrote: ↑
Sun Sep 26, 2021 8:51 pm
Lightweight starting handles are not standard, they are a different length. I can measure one of mine if you need to know the length
Yes, please! Thanks.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: Lightweight starting handle??

Post by weetchus » Tue Sep 28, 2021 1:39 am

Okay. Important thing is to make a rough wire template by poking the handle end through the hole in the bonnet (shown below), then making sure the first and second bends lead to the long straight section lining up with the two raised aluminium table like brackets spot welded to the underside of the bonnet. One of my table brackets is missing and the brass bracket clip holder thing is a home made version of the starter handle bracket holder that came with the vehicle originally, but rusted out.
PXL_20210928_003055482.jpg
PXL_20210928_003055482.jpg (3.54 MiB) Viewed 4843 times
PXL_20210928_002740395.jpg
PXL_20210928_002740395.jpg (1.92 MiB) Viewed 4843 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: Lightweight starting handle??

Post by weetchus » Tue Sep 28, 2021 2:08 pm

Screen Shot 2021-09-28 at 9.07.44 am.png
Screen Shot 2021-09-28 at 9.07.44 am.png (2.31 MiB) Viewed 4833 times
Screen Shot 2021-09-28 at 9.07.31 am.png
Screen Shot 2021-09-28 at 9.07.31 am.png (1.78 MiB) Viewed 4833 times

Botsie
Posts: 46
Joined: Thu Oct 03, 2019 5:49 pm

Re: Lightweight starting handle??

Post by Botsie » Tue Sep 28, 2021 4:59 pm

Nice one!

Botsie
Posts: 46
Joined: Thu Oct 03, 2019 5:49 pm

Re: Lightweight starting handle??

Post by Botsie » Tue Sep 28, 2021 6:58 pm

Following up on the door check brackets (I mean the tubular brackets that retain the check rods with their rubber bung), are these the same as those fitted on the civvy SIIA? I need a pair........the check rods and bungs seem readily available.

Post Reply