Page 5 of 18

Re: 19HF27

Posted: Wed Apr 08, 2020 7:20 pm
by Bob Fell
Hi Loulou,
Thank you, that is interesting but I must say with 4.8mm Land rover steel mandrel aluminum head closed rivets I have found such a tool hard work. As said I've used a good quality air riveter in the past with no problems. With the manual pliers I've found you cannot control the slip as the mandrel breaks whereas with an air riveter you can having a spare hand to hold the head shrouded with a cloth to prevent collateral damage to the paintwork if you get my drift - try it.
Regards
Bob

Re: 19HF27

Posted: Wed Apr 08, 2020 7:29 pm
by AR4412
Loulou wrote: ↑
Wed Apr 08, 2020 3:01 pm

For the rivet pliers, I tested an air-compressed model once: it is brutal (in my opinion) and I scratched the paint when the nail broke while sliding.
I find that problem with 'lazy tongs', or long arm riveters. Lazy tongs can 'bounce' when the rivet lets go, unless your second hand is braced against the panel being rivetted you run the risk of it striking the panel, and long arm riveters cannot be braced as both hands are needed on the tool leaving the sharp end free to go where it wants. I, however, have no problems with an air riveter, but everyone will have their prefered type of tool and will be more successful with one type than the other. Sometimes there just isn't the space to get a long tool in to where you are riveting, and sometimes you have to fit more rivets than you want to count, and here the air riveter is ideal. I do have all three types in the armoury, but the air tool is the weapon of choice for a serious day on the ranges.

Bob, (Hiya! :D ), I have been using a Sealey air riveter for many a year now. It has stood up to the use and abuse it's had well, and has even survived hitting the floor a few times. Going by the fact that it is red, and not black, I believe it's an SA31.

Regards,

Re: 19HF27

Posted: Wed Apr 08, 2020 11:31 pm
by landylees
Have to agree with Bob and Neil. I have a hand riveter but it was forever bouncing off the panels afterwards, so I bought a Sealey Air Riveter and have never looked back. I have the red one too and it looks like an SA31

Re: 19HF27

Posted: Thu Apr 09, 2020 10:20 am
by Loulou
You are surely right by your experience.
I scratched the paint once and unhappy enough not to start over.
So I use a thick cardboard mask for each pose and in the event of inadvertent slipping, the cardboard protection takes the shock. In short, the middle ages of rivet laying. :mrgreen:
Also, I was advised to use only aluminum + aluminum rivets so that there is no "electrical" corrosion between the aluminum and the possible rod in the case of a steel rod. .

Good late morning

Looloo

Re: 19HF27

Posted: Thu Apr 09, 2020 10:55 am
by removeduser185
I have been using lazy tongs and have quite a few scratches on the paitnwork to show for it. They certainly do bounce unfortunately and you can't always get your spare hand in the right place to cushion the bounce. I also have a pair of pliers-type rivetters, but find them too difficult to manage with arthriticky hands unless I put a piece of pipe on each handle to lengthen them - but they sit in the mobile toolbox for emergencies.

I was late to air tools as I only got hold of a compressor when it came time to do serious spray painting, but, were I to start another project of this sort, I would arm myself in advance with a good range of them. I now swear by my air grease gun and I have just bought a small air ratchet though have yet to use it as the problem on the Discovery which I bought it to fix hasn't recurred. Perhaps an air rivetter for next Christmas!

Re: 19HF27

Posted: Thu Apr 09, 2020 7:05 pm
by Bob Fell
Thanks all for the input, much appreciated :D
Sealey SA31 ordered, cheers Neil and landylees :D, a lot of hard work done over the last couple of days now leaves the tub sorted and ready for riveting the refurbed nut plates and new lower seat belt eye mounting brackets back in place.
A couple of pics but the don't really show much;
002.jpg
002.jpg (2.96 MiB) Viewed 2609 times
Started to sort the fastenings, got most but need a few sheradized washers and rivets from Mr Arnold which will be ordered tomorrow.
003.jpg
003.jpg (2.61 MiB) Viewed 2609 times
One really good thing is I don't have to move the URS - bliss :D
Regards
Bob

Re: 19HF27

Posted: Thu Apr 09, 2020 8:12 pm
by AR4412
Hiya Bob! :D ,

I was glad of the air riveter today, as I'm converting a 90 truck cab into a station wagon at work. With the cappings and windows etc, a total of 136 rivets fitted today.
CSW.jpg
CSW.jpg (30.85 KiB) Viewed 2603 times
Good to see that your tub isn't showing any major corrosion where the steel meets aluminium. 8-)

Regards,

Re: 19HF27

Posted: Mon Apr 20, 2020 8:33 pm
by Bob Fell
Hiya Neil :D ,
Know what you mean mate, just imagine with a hand riveter :cry:
The Sealey is a gem, just as good as the Draper if not better :D
Today all the bits and pieces from Mr Arnold finally arrived so was able to crack on;
011.jpg
011.jpg (3.07 MiB) Viewed 2531 times
Duralac's strange stuff, coated tub and component surfaces , allowed to touch dry, fitted and riveted, dead easy,
009.jpg
009.jpg (2.86 MiB) Viewed 2531 times
And NO, I'm not painting the rivet heads;
002.jpg
002.jpg (2.61 MiB) Viewed 2531 times
Tomorrow all underside will get a Dinitrol bomb and finish off the tailgate refurb with a delivery from Mr Blanchard.
Regards
Bob

Re: 19HF27

Posted: Mon Apr 20, 2020 8:50 pm
by removeduser185
That's looking great and, to be original, I don't think the rivets should be painted as the seatbelt mount and the tie-down brackets would have been added after the tub was made up and sprayed. I had this debate with myself. Initially I carefully scratched all the rivets clean on the tub until, when I was sitting there in my thinking chair, I realised that that wouldn't be correct, so I painted them again leaving only those which would have been added after the tub was made up unpainted.

Re: 19HF27

Posted: Tue Apr 21, 2020 7:29 pm
by Bob Fell
Hiya Fred :D ,
Conundrums, conundrums my friend.
As you well know in service vehicles were painted, painted and painted but I've just decided to leave them as is and lets face it with a bloody large URS in place, what does it matter.
Cheers and best to you,
Hope to meet one day,
Bob