Page 4 of 18

Re: 19HF27

Posted: Sat Apr 04, 2020 4:09 pm
by Bob Fell
And finally fitted the O/S mirror to complete that little project.
I make no apology for the gratuitous mirror pics as I'm over the moon with the result :D ;
009.JPG
009.JPG (152.53 KiB) Viewed 2408 times
010.JPG
010.JPG (152.32 KiB) Viewed 2408 times
011.JPG
011.JPG (162.21 KiB) Viewed 2408 times
Regards
Bob

Re: 19HF27

Posted: Sat Apr 04, 2020 11:21 pm
by landylees
Looks great!

Re: 19HF27

Posted: Mon Apr 06, 2020 5:45 pm
by Bob Fell
Today started unbolting the tub top panels, the nut plates have been removing themselves as the rivets are rotted off.
What I have found and didn't know is that the nut plates are cranked and the gaps were filled with a white, hard putty which initially through me into a panic thinking it was the dreaded corrosion of doom, but no, once cleaned up there was no corrosion at all :D. With regards to the putty, I've come across this before with evidence it was used as a sealant on the Sankey hub ends and also one of the drive end plates when I replaced the rear hub oil seals. I believe it maybe boss white? The first pic shows traces of it on one of the plate;
006.jpg
006.jpg (3.81 MiB) Viewed 2374 times
Anyway, the two plates I have removed have cleaned up a treat;
007.jpg
007.jpg (167.68 KiB) Viewed 2374 times
More tomorrow.
Bob

Re: 19HF27

Posted: Tue Apr 07, 2020 7:00 pm
by Bob Fell
Lots done today with the lovely weather;
002.jpg
002.jpg (3.68 MiB) Viewed 2339 times
003.jpg
003.jpg (3.24 MiB) Viewed 2339 times
Well that's a couple of gratuitous pics out the way, here's the end result of today's work;
005.jpg
005.jpg (2.54 MiB) Viewed 2339 times
006.jpg
006.jpg (2.97 MiB) Viewed 2339 times
Every thing went well, the black is etch primer from Fascinating Finishes military range, brilliant stuff as it goes these days but not to the standard of yellow chromate aka
Alodine of the old days.

Re: 19HF27

Posted: Tue Apr 07, 2020 7:15 pm
by Bob Fell
Following on;
007.jpg
007.jpg (2.99 MiB) Viewed 2337 times
008.jpg
008.jpg (2.63 MiB) Viewed 2337 times
Now, advice required, as said there is some minor surface aluminum rot which I have cleaned of as best as you can in what can only be the most inaccessible area of all on these vehicles;
009.jpg
009.jpg (3.37 MiB) Viewed 2337 times

What is the best treatment/paint from here before refitting the nut plates? I'm thinking of using HIPS as a gasket possibly between the nut plates and tub. Any advice welcome.
Cheers
Bob

Re: 19HF27

Posted: Tue Apr 07, 2020 9:06 pm
by landylees
I'm putting mine back together with Duralac inbetween the different metals.

https://www.amazon.co.uk/Duralac-Anti-C ... B00LB6EUEO

Re: 19HF27

Posted: Tue Apr 07, 2020 9:09 pm
by removeduser185
I used a coat of the resin you use with fibreglass. It seems to be tough and suitably insulating.

Re: 19HF27

Posted: Wed Apr 08, 2020 6:24 am
by Loulou
Waa!

A very beautiful LWT AND its radio module.
All my respectful congratulations dear Bob for the job accomplished; It's amazing !

Looloo

Re: 19HF27

Posted: Wed Apr 08, 2020 10:33 am
by Bob Fell
Thanks all for the advice, I'm thinking Duralac is the way to go.
Now, I'm after an air riveter, can any one recommend any particular make/model they have found reliable???
There are shed loads out there and I wouldn't touch a cheap one so I would appreciate experiences before I wade in.
I've used a Draper before and that was excellent but unfortunately not available to me anymore.

Regards
Bob

Re: 19HF27

Posted: Wed Apr 08, 2020 3:01 pm
by Loulou
I repainted the nut plates with bi-component polyurethane paint, the tub also.
Then a flexible polyurethane sealant between the two during assembly and finally a nice layer of grease (semi-trailer sole of quarries) on top.

For the rivet pliers, I tested an air-compressed model once: it is brutal (in my opinion) and I scratched the paint when the nail broke while sliding.
I now use this manual pliers with large levers (better control) and it is perfect with waterproof aluminum + aluminum rivets.
The head is a little big and sometimes difficult to put in place.
pop-manu.png
pop-manu.png (267.06 KiB) Viewed 2282 times
Hoping to have helped

Looloo