Monty the rather rusty 2A - 37FG31
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
More spot welding. Both footwells are now pretty much done, although I’ll go around the whole thing again at the end just to make damn sure nothing is ever coming loose.
The ratchet strap is to keep the footwell tight in the slots in the hinge panel while I welded it together:
The two clamps are holding bits where it’s really hard to get in with the arms of the spot welder. I’ll figure this out tomorrow (I hope):
There’s a bit of surface rust on the fascia panel as the garage has been damp with all this relentless rain. No big deal though as the whole bulkhead will be treated before paint.
I still need to:
Fit the heater panel
Repair & fit the dash box
Bend the lips on the outer two dash recesses
Find out how to make the welder reach around the top of the hinge panels to do the uppermost edge (may have to resort to puddle welding these sections with the MIG).
Drill all the various dash holes
.. and some other stuff I forgot no doubt.
I’ll take this afternoon’s progress as a win though, as I’m not far off done with the welding.
All the best,
Andy
P.S. Howard, you were right - electrodes just needed a clean up. The welds are much bigger diameter now.
The ratchet strap is to keep the footwell tight in the slots in the hinge panel while I welded it together:
The two clamps are holding bits where it’s really hard to get in with the arms of the spot welder. I’ll figure this out tomorrow (I hope):
There’s a bit of surface rust on the fascia panel as the garage has been damp with all this relentless rain. No big deal though as the whole bulkhead will be treated before paint.
I still need to:
Fit the heater panel
Repair & fit the dash box
Bend the lips on the outer two dash recesses
Find out how to make the welder reach around the top of the hinge panels to do the uppermost edge (may have to resort to puddle welding these sections with the MIG).
Drill all the various dash holes
.. and some other stuff I forgot no doubt.
I’ll take this afternoon’s progress as a win though, as I’m not far off done with the welding.
All the best,
Andy
P.S. Howard, you were right - electrodes just needed a clean up. The welds are much bigger diameter now.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
You wouldn’t have said that if you had been watching Steve. A lot of trying to balance bits, needing a third (and fourth) hand, dropping things, swearing, pleading with inanimate objects to just bloody well cooperate- that sort of thing. I’ll get there in the end. Probably literally the end of me!
Re: Monty the rather rusty 2A - 37FG31
Hiya Andy!
,
Good to see you have firmly grasped the bulkhead demon by it's dangly bits, given them a good squeeze and are cracking on whilst he is distracted. You should have yourself a serviceable bulkhead in no time mate.
Regards,
Good to see you have firmly grasped the bulkhead demon by it's dangly bits, given them a good squeeze and are cracking on whilst he is distracted. You should have yourself a serviceable bulkhead in no time mate.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Hiya buddy, I want the thing in anti rust primer before winter so I can hit the ground running in spring. Of course, I’ll also need to find a way to get it past the gate guardian and into the warm dry house for a few months.. do you think she would fall for me booking her a spa day?
Re: Monty the rather rusty 2A - 37FG31
She might let you think you have got away with it, right up until she gets back from said spa day and gives you both barrels.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
It’s almost as if you’re speaking from experience Neil
Well today I got most of the rest of the spot welding done. I say ‘most, because I stuffed up the heater panel placement.
It’s too high up, so the vanity panel that bolts to the curved section won’t quite meet the floor. Schoolboy error! One of those, ‘don’t know how I actually managed that’ moments.
No bother, I have a spare sheet of steel so will fix that tomorrow, just in time to drop the welder back off with Howard.
What a rigmarole.. I will be glad when this bulkhead finally accepts defeat.
Andy
Well today I got most of the rest of the spot welding done. I say ‘most, because I stuffed up the heater panel placement.
It’s too high up, so the vanity panel that bolts to the curved section won’t quite meet the floor. Schoolboy error! One of those, ‘don’t know how I actually managed that’ moments.
No bother, I have a spare sheet of steel so will fix that tomorrow, just in time to drop the welder back off with Howard.
What a rigmarole.. I will be glad when this bulkhead finally accepts defeat.
Andy
Re: Monty the rather rusty 2A - 37FG31
Whaa!
Bravo, for me ... it's really precision watchmaking.
I do not know how to weld ...
looloo
Bravo, for me ... it's really precision watchmaking.
I do not know how to weld ...
looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)
Re: Monty the rather rusty 2A - 37FG31
Hi Andy,
Damned good work on the bulkhead, despite the little error.
Keep up the good work.
Regards
Bob
Damned good work on the bulkhead, despite the little error.
Keep up the good work.
Regards
Bob
042Bobf
19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.
19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.
Re: Monty the rather rusty 2A - 37FG31
I'm sure I don't know what you mean? After all, who in their right mind would fill their house with restored and painted bits of Lightweight?andrewjsimpson1977 wrote: ↑Wed Oct 16, 2019 6:12 pmIt’s almost as if you’re speaking from experience Neil![]()
Hopefully it won't take you too long to rectify the little panel mistake.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.