DIY Tools. Who has the best to share!?

Any information on all other kit
landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: DIY Tools. Who has the best to share!?

Post by landylees » Thu Jun 11, 2020 9:52 pm

My contribution is also a steering relay spring compressor - first "tool" I ever made with the spot welder and the angle iron I used was too thin so it bends alarmingly when you are compressing the spring!
Land Rover Special Tool 2.JPG
Land Rover Special Tool 2.JPG (1.36 MiB) Viewed 12798 times
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: DIY Tools. Who has the best to share!?

Post by andrewjsimpson1977 » Thu Jun 11, 2020 10:17 pm

Oh it’s that game is it :D

I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..

8A0D718E-6B71-492E-B119-7987DA70857C.jpeg
8A0D718E-6B71-492E-B119-7987DA70857C.jpeg (782.19 KiB) Viewed 12793 times
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg (856.53 KiB) Viewed 12793 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: DIY Tools. Who has the best to share!?

Post by weetchus » Fri Jun 12, 2020 2:32 pm

"bends alarmingly" hahaha
:lol:
landylees wrote: ↑
Thu Jun 11, 2020 9:52 pm
My contribution is also a steering relay spring compressor - first "tool" I ever made with the spot welder and the angle iron I used was too thin so it bends alarmingly when you are compressing the spring!
Land Rover Special Tool 2.JPG

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: DIY Tools. Who has the best to share!?

Post by weetchus » Fri Jun 12, 2020 2:41 pm

I tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!

andrewjsimpson1977 wrote: ↑
Thu Jun 11, 2020 10:17 pm
Oh it’s that game is it :D

I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..


8A0D718E-6B71-492E-B119-7987DA70857C.jpeg


1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: DIY Tools. Who has the best to share!?

Post by andrewjsimpson1977 » Fri Jun 12, 2020 2:52 pm

weetchus wrote: ↑
Fri Jun 12, 2020 2:41 pm
I tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!

andrewjsimpson1977 wrote: ↑
Thu Jun 11, 2020 10:17 pm
Oh it’s that game is it :D

I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..


8A0D718E-6B71-492E-B119-7987DA70857C.jpeg


1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
I just remember making dammed sure neither my face or unmentionables were directly in the firing line at any time. The process was:

1) Clamp it up

2) Rush it over to the relay body muttering rude words under my breath repeatedly

3) Tap it in the hole, while becoming temporarily religious

4) Release each clamp with the same care one might employ whilst taking the pin out of a very old and rusty grenade

5) Shout “YES!” loudly when you realise it has broken with tradition and gone in first time.

I believe from other’s experiences, that I was very lucky on this one.

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: DIY Tools. Who has the best to share!?

Post by landylees » Fri Jun 12, 2020 7:40 pm

andrewjsimpson1977 wrote: ↑
Fri Jun 12, 2020 2:52 pm
weetchus wrote: ↑
Fri Jun 12, 2020 2:41 pm
I tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!

andrewjsimpson1977 wrote: ↑
Thu Jun 11, 2020 10:17 pm
Oh it’s that game is it :D

I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..


8A0D718E-6B71-492E-B119-7987DA70857C.jpeg


1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
I just remember making dammed sure neither my face or unmentionables were directly in the firing line at any time. The process was:

1) Clamp it up

2) Rush it over to the relay body muttering rude words under my breath repeatedly

3) Tap it in the hole, while becoming temporarily religious

4) Release each clamp with the same care one might employ whilst taking the pin out of a very old and rusty grenade

5) Shout “YES!” loudly when you realise it has broken with tradition and gone in first time.

I believe from other’s experiences, that I was very lucky on this one.
Andy, given how much work you have to do on your project, shouldn't you be outside working on it so you have something to post later ?
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: DIY Tools. Who has the best to share!?

Post by andrewjsimpson1977 » Fri Jun 12, 2020 7:54 pm

I painted some nut plates what more do you want, blood?

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: DIY Tools. Who has the best to share!?

Post by weetchus » Thu Jun 25, 2020 12:44 am

Haha. This thread needs to keep going. Love the "temporarily religious" comment.

Post Reply