DIY Tools. Who has the best to share!?
Re: DIY Tools. Who has the best to share!?
My contribution is also a steering relay spring compressor - first "tool" I ever made with the spot welder and the angle iron I used was too thin so it bends alarmingly when you are compressing the spring!
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: DIY Tools. Who has the best to share!?
Oh it’s that game is it
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
Re: DIY Tools. Who has the best to share!?
"bends alarmingly" hahaha
Re: DIY Tools. Who has the best to share!?
I tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!
andrewjsimpson1977 wrote: ↑Thu Jun 11, 2020 10:17 pmOh it’s that game is it![]()
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
8A0D718E-6B71-492E-B119-7987DA70857C.jpeg
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: DIY Tools. Who has the best to share!?
I just remember making dammed sure neither my face or unmentionables were directly in the firing line at any time. The process was:weetchus wrote: ↑Fri Jun 12, 2020 2:41 pmI tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!
andrewjsimpson1977 wrote: ↑Thu Jun 11, 2020 10:17 pmOh it’s that game is it![]()
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
8A0D718E-6B71-492E-B119-7987DA70857C.jpeg
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
1) Clamp it up
2) Rush it over to the relay body muttering rude words under my breath repeatedly
3) Tap it in the hole, while becoming temporarily religious
4) Release each clamp with the same care one might employ whilst taking the pin out of a very old and rusty grenade
5) Shout “YES!” loudly when you realise it has broken with tradition and gone in first time.
I believe from other’s experiences, that I was very lucky on this one.
Re: DIY Tools. Who has the best to share!?
Andy, given how much work you have to do on your project, shouldn't you be outside working on it so you have something to post later ?andrewjsimpson1977 wrote: ↑Fri Jun 12, 2020 2:52 pmI just remember making dammed sure neither my face or unmentionables were directly in the firing line at any time. The process was:weetchus wrote: ↑Fri Jun 12, 2020 2:41 pmI tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!
andrewjsimpson1977 wrote: ↑Thu Jun 11, 2020 10:17 pmOh it’s that game is it![]()
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
8A0D718E-6B71-492E-B119-7987DA70857C.jpeg
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
1) Clamp it up
2) Rush it over to the relay body muttering rude words under my breath repeatedly
3) Tap it in the hole, while becoming temporarily religious
4) Release each clamp with the same care one might employ whilst taking the pin out of a very old and rusty grenade
5) Shout “YES!” loudly when you realise it has broken with tradition and gone in first time.
I believe from other’s experiences, that I was very lucky on this one.
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: DIY Tools. Who has the best to share!?
I painted some nut plates what more do you want, blood?
Re: DIY Tools. Who has the best to share!?
Haha. This thread needs to keep going. Love the "temporarily religious" comment.