Lightweight FFR 24v wiring can anyone help?
Lightweight FFR 24v wiring can anyone help?
I’m currently building up a 24v lightweight from the ground up from a pile of new and used parts. I’m trying to find out where the wiring from the shunt box goes to the double ammeters on the dash…
There is an additional heavy duty wire and a thick brown and white wire that seem to terminate at a white circle on the wiring diagram, not the starter solenoid as I would expect… a feed to the IR relay seems to come from it with a fuse as well?
Is there an additional terminal that I need to connect to? It’s probably dead obvious but I really haven’t got a scooby!
Can anyone put me straight?
Kind regards David
There is an additional heavy duty wire and a thick brown and white wire that seem to terminate at a white circle on the wiring diagram, not the starter solenoid as I would expect… a feed to the IR relay seems to come from it with a fuse as well?
Is there an additional terminal that I need to connect to? It’s probably dead obvious but I really haven’t got a scooby!
Can anyone put me straight?
Kind regards David
- fv1620
- Bake Off Judge
- Posts: 2268
- Joined: Thu Oct 06, 2011 2:16 pm
- Location: GB-CMN (formerly UK91)
- Contact:
Re: Lightweight FFR 24v wiring can anyone help?
David I can't tell you the route that the wires take to the ammeters, but below are the connections within the shunt box.
Clive Elliott
Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.
Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.
Re: Lightweight FFR 24v wiring can anyone help?
That is really helpful. Thank you!
Re: Lightweight FFR 24v wiring can anyone help?
Hi David,
On the original wiring diagram in the User Handbook, that circle is annotated in the item list as being a 'Terminal Post'. Which to me, suggests it is just a joiner for the three wires. Unfortunately my '73 FFR had had the FFR charging system chopped out, the vehicle converted to 12v, and the wiring put to as you would find on a GS when I got it. But, I have a hazy memory of there being an insulated post in the dash behind the ammeter panel. The wiring on the later FFR I have is different, so I can be no help to you there. Do the wires have ring terminals on their ends? If they do, you could try connecting them together with a bolt/crocodile clip to see if the circuits give continuity to where it needs to be each end. Just make sure that nothing can earth out before doing a 'live feed' test. There are various types of insulated wiring posts available to make a proper connection.
Regards,
On the original wiring diagram in the User Handbook, that circle is annotated in the item list as being a 'Terminal Post'. Which to me, suggests it is just a joiner for the three wires. Unfortunately my '73 FFR had had the FFR charging system chopped out, the vehicle converted to 12v, and the wiring put to as you would find on a GS when I got it. But, I have a hazy memory of there being an insulated post in the dash behind the ammeter panel. The wiring on the later FFR I have is different, so I can be no help to you there. Do the wires have ring terminals on their ends? If they do, you could try connecting them together with a bolt/crocodile clip to see if the circuits give continuity to where it needs to be each end. Just make sure that nothing can earth out before doing a 'live feed' test. There are various types of insulated wiring posts available to make a proper connection.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: Lightweight FFR 24v wiring can anyone help?
Hi, Thank you for your help! That would make perfect sense as there is a chunky wire shown going from the shunt box to the solenoid and then a heavy duty brown and white wire going to the ‘post’ that feeds every thing else.
I’ve had to replace the heavy duty wire in the ammeter loom as the rubber had perished. I now need to work out where the armoured cable sleeve ends up - I assume the end unscrews to connect to a panel hole?
The terminals are ‘ring’ terminals…
I am currently making nylon sleeves for the control box that I have now found the brackets for to go behind the drivers seat. Although there is a numbered part in the parts diagram the number is omitted when it comes to part numbers.
Thanks again and if I could work out how to add photos I would do!
I’ve had to replace the heavy duty wire in the ammeter loom as the rubber had perished. I now need to work out where the armoured cable sleeve ends up - I assume the end unscrews to connect to a panel hole?
The terminals are ‘ring’ terminals…
I am currently making nylon sleeves for the control box that I have now found the brackets for to go behind the drivers seat. Although there is a numbered part in the parts diagram the number is omitted when it comes to part numbers.
Thanks again and if I could work out how to add photos I would do!
Re: Lightweight FFR 24v wiring can anyone help?
I am also building a late 2a lightweight with my son (the one with series 3 style wings). Still in the early stages but do have that section of crumbly bulkhead with wiring at work do I can see if a ‘post’ exists there? Thanks again and- David
Re: Lightweight FFR 24v wiring can anyone help?
Worked out how to add photos… progress so far!
Re: Lightweight FFR 24v wiring can anyone help?
Ooooh! Shiny!
We like shiny we do. And cake.
I did find this in the 24V Cables and Fittings section of the SIII parts list. (Terminal Post Assembly. P/No C22257. NSN 5940-99-829-8567.)
Following the number trail led me to this.
https://pablanchard.co.uk/Terminal-Stud ... Was-565829
I haven't had the chance to see if there is similar listed in the IIA parts list yet.
Regards,
We like shiny we do. And cake.
I did find this in the 24V Cables and Fittings section of the SIII parts list. (Terminal Post Assembly. P/No C22257. NSN 5940-99-829-8567.)
Following the number trail led me to this.
https://pablanchard.co.uk/Terminal-Stud ... Was-565829
I haven't had the chance to see if there is similar listed in the IIA parts list yet.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: Lightweight FFR 24v wiring can anyone help?
Thanks again for the advice.
Managed to get one this afternoon but unfortunately missed the post!
Hopefully it will arrive Saturday…
Unfortunately, what remains of my son’s lower bulkhead is only fragments where the wiring and relays once lived… everything else was weighed in. However, looking at the 2a wiring diagram I’m not sure it had one.
Kind regards, David
Managed to get one this afternoon but unfortunately missed the post!
Hopefully it will arrive Saturday…
Unfortunately, what remains of my son’s lower bulkhead is only fragments where the wiring and relays once lived… everything else was weighed in. However, looking at the 2a wiring diagram I’m not sure it had one.
Kind regards, David