Starting Issues: Weber Carb

If you have encountered or solved a problem post here
User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: Starting Issues: Weber Carb

Post by fv1620 » Thu Jun 08, 2023 8:42 am

Two schools of thought with coil terminals. Pointing downwards is the most dependant point for water to collect say from driving in heavy rain or paddling. If wet there can be HT leakage. If the internal screw & washer for HT terminal has loosened as it is the filler point for the oil & can leak downwards.

If the coil terminals are top most then it is better protected from water splashing upwards & if there is water it will drain away better. If there has been some oil loss it is less likely to lose more as the filler point is uppermost. Although if there has been leakage then the HT output will be devoid of insulation at its most vulnerable point as it leaves the coil at the top. Whereas downwards the oil will be bound to be bathing and protecting the internal wires at their most vulnerable point.

So on balance if your coil has not leaked & you don't go paddling or heavy rain driving, I don't think the orientation matters & often these ignition lead sets have a king lead that dictates how the coil is best positioned as they are often a bit short.

Make sure that you are using a coil designed for negative earth & the LT connections are the correct way round. Contrary to what some think it is not necessary for the coil case to be properly earthed.

Check that the HT leads have similar resistance of similar length & a higher resistance if longer. Don't fall into the trap of fitting copper wire leads unless you have resistive plugs & connectors. Resistance is necessary to not only help reduce RFI but it reduces erosion of the sparking plugs & distributor.

When you clean the sparking plugs, be aware that sand-blasting cleans it up of carbon nicely but microscopically rounds the edges of the terminals so always so gently file them & check the gap & wash dust off in a solvent & air blast dry. A spark likes to jump from a sharp edge, if it is slightly rounded from use or sandblasting, it needs a higher voltage to jump & may give poor running.

You are certain that you have the correct type of sparking plug for your engine & despite be a good make are not fakes as there are some around? After an attempted running check the state of the plugs that should be would light brown not oily or petrol soaked or carbony.

Have you done a compression test to ensure that is OK?

I once had a strange fault after I fitted a new military fuel pump from a sealed box. It seemed to function but sometimes didn't then work againk it gave a strange running experience. I tool it apart & some nit-wit had not assembled it correctly so that the central spigot of the diaphragm did not always engage its end to be caught by the slot in the lift arm. So it had been assembled one set of screw holes out of sync. The way I spotted it was to disconnect the fuel pipe from the carb & feed it into a collecting vessel then hand pump it for a minute to see if every stroke delivered an output.
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: Starting Issues: Weber Carb

Post by weetchus » Tue Jun 13, 2023 2:29 am

Hi Clive,

Good news. I seem to have the problem sorted!

I got a new set of HT leads (ERC3256) from Lucas, cleaned the spark plugs again and checked their gaps. Installed everything with the new, shorter (and neater) leads which are about half the length of the old ones... which looked like a spaghetti mess when all in place.

Set the carb at two turns out on the mixture screw and 1 1/2 turns in on the idle screw.

Started right up and was able to reduce the idle screw by about 1/2 a turn or more, and leaned the mixture screw by turning it in about 1 turn. So should be nice and lean.

The old HT leads must have been bad or too long. Perhaps the resistance was affected.

Will look at repositioning the coil sideways.
Definitely have the right plugs BP5ES. Will take a look at them once I have run the truck for a while to see how they look.
I did a leak down test, which is better than a compression test and everything passed with flying colours.

The fuel pump is working and I rebuilt it carefully.

Amazing advice all. Got there in the end.

Thanks for all the help.
Screenshot 2023-06-12 at 9.28.35 PM.png
Screenshot 2023-06-12 at 9.28.35 PM.png (3.86 MiB) Viewed 2045 times

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Starting Issues: Weber Carb

Post by AR4412 » Tue Jun 13, 2023 5:19 am

Hi Alex,

Clive is an electrics guru, and everyone needs one in their toolkit. (Hiya Clive! :D ).

Good to read that you have got the engine running nicely, and have enjoyed a drive in the Lightweight. :D

Defective leads would explain why it sounded like the timing was out/firing order was wrong, as if the leads were touching the spark can jump from one lead to another, delivering the spark to the wrong cylinder at the wrong time.

I hope that going out for that drive put a smile on your face.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: Starting Issues: Weber Carb

Post by Loulou » Tue Jun 13, 2023 7:03 am

Well… this all seems to end with a smile.

Indeed, with Clive Eliot's comments and suggestions we feel less alone, thank you for his help.

Without wanting to bring bad luck, you are still going to have a period (which I hope will be as short as possible!) with broken odds and ends, everything should stabilize now.

Vamos a la playa !

Looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: Starting Issues: Weber Carb

Post by fv1620 » Tue Jun 13, 2023 9:04 am

Well done Alex, I am sure you now have a lasting glow of satisfaction, which would not be there if you simply took it to a garage to sort out & paid through the nose. These failures are unpleasant & frustrating at the time but will add to your pride of Rover ownership. Your investigative enthusiasm was there, it just had to be redirected. It often takes an outsider to realign the diagnostic pathway.

There will come a time when some poor soul will have problems similar to yours & you can step in with your experience, which is how we all learn.
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: Starting Issues: Weber Carb

Post by weetchus » Tue Jun 13, 2023 2:51 pm

Words of wisdom from a true guru Clive.
I hope one day to be solving someone's Land Rover issues. I feel good just helping someone change a tyre to be honest!
Probably the more likely use of any skills I learn with all modern cars being automatic, electric and semi-conductor-ed these days.
That said, I changed my modern car's disc rotors and pads the other day and saved myself $$$.

Vamos a la playa indeed LooLoo.
Neil, the long leads may well have been passing current across each other. Now, all leads are short and neat. I can get my hands to the fuel pump and oil filter without snagging on a cable.

Thanks again all. Happy endings is what this community is all about :? :lol:

diffwhine
Posts: 389
Joined: Sun Feb 25, 2018 9:28 pm

Re: Starting Issues: Weber Carb

Post by diffwhine » Tue Jun 13, 2023 6:30 pm

I'll second that and the Wagon looks great!
Puts my paltry efforts at getting mine completed in the shade.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: Starting Issues: Weber Carb

Post by weetchus » Sun Jun 18, 2023 11:17 am

Thanks diffwhine, it's only taken 4+ years.
Would have been faster without budget restrictions 😜

Post Reply