Strange fuel gauge readings

If you have encountered or solved a problem post here
User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: Strange fuel gauge readings

Post by fv1620 » Wed Mar 08, 2023 9:22 pm

Thanks Neil it is based on a diagram I found in a SEME précis handout. As you know these publications are very good at explaining things in a down to earth manner. I think that diagram helps to illustrate the effect of opposing magnetism from the two coils at right angles to each other. Particularly as the coil giving the magnetic pull to the needle towards 'empty' is fed directly from the earthy end and this is only noticeable when there is no significant magnetic pull from the 'full' coil when the tank is empty.

As the original fuel gauge system did once work, I can't help but feel there is an earthing issue. Unfortunately a merry dance is being led on HMVF from various opinions that look not too promising at reaching a resolution I'm afraid.
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Strange fuel gauge readings

Post by AR4412 » Wed Mar 08, 2023 9:50 pm

I don't remember seeing that diagram in my precis' when training at SEME, so maybe it's one that the Vehicle Electricians had and the Vehicle Mechanics didn't get. It's been a good few decades since I did my basic VM couse, so I may have forgotten that I did see it. I still have every precis' from every course I did at SEME so I may go hunting for it in my 'Basics' ones.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: Strange fuel gauge readings

Post by fv1620 » Wed Mar 08, 2023 10:16 pm

Neil that particular one is 'LANDROVER' SEME REF NO: PR 265 Ver 2 2005

It is mainly TUL/TUM (HS) with a little bit of 90/110. It has proper circuit diagrams unlike the pages & pages of wires disappearing down blocks of looms that are covered in the AESPs. At least you can follow a wire through the entire circuit & see where it goes & what it does, rather than woolly mystique of the AESP illustrations.

I have quite a lot of the SEME books including many copy & paste originals from which the series were printed, which gives access to crisp images unlike copies of copies.
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Strange fuel gauge readings

Post by AR4412 » Wed Mar 08, 2023 10:30 pm

Thanks for the Reference Number Clive, now I don't have to go looking as I know I don't have that one.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

ScarboroughSeadog
Posts: 7
Joined: Tue Mar 07, 2023 4:06 pm

Re: Strange fuel gauge readings

Post by ScarboroughSeadog » Fri Mar 10, 2023 12:25 pm

AR4412 wrote: ↑
Sat Sep 19, 2020 11:46 am
With the fuel change over tap in the central position I would expect the fuel gauge to read the same as when the ignition is off, as there is no path to earth from the gauge through the switch and sender without a plunger being depressed. If there is a reading on the gauge with the tap in this position and the ignition on, there may be a short to earth somewhere in the wiring, or a plunger in a switch has stuck.

Check that the plungers are not stuck in the sender switches, they should protrude by about 3mm or so. IIRC they go in by about 2mm when pushed in by the tap on mine, But, it was a long time ago when I did them. I set mine up with the ignition on, adjusting them downwards until they break the circuit without 'bottoming out'. Their height can also be set using a multimeter.

Try removing the green/black wires from the switches, if the gauge gives any reading with the ignition on, then the wire from the gauge to the tap switches, or the gauge itself could be shorting to earth. If the gauge reads zero with ignition on then the fault is possibly with one of the switches. With the tap in the central postion, so that neither switch plunger is pressed in, and the wires from the tank senders removed, connect the Green/Black wire to one of the switches and observe the gauge for movement, then try the other. If the needle moves up when connected to a switch it could be that that switch is earthing out inside.

Linking the Green/Black wire direct to earth/battery negative should have the gauge reading maximum, and is a quick way to check that the circuit to the tap switches is okay.

Linking the Green/Black wire to either of the sender wires should read the level in that tank. (Or nothing if the sender unit is faulty or not earthing.).

Regards,
Is this correct? I had understood the opposite ie that the Lucas switches were NC (normally closed) so they make the circuit when the nipple is NOT depressed/activated. When the changeover tap depresses the nipple, that cuts the circuit, and stops the reading from the associated tank. Thanks

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Strange fuel gauge readings

Post by AR4412 » Fri Mar 10, 2023 1:34 pm

My mistake there. :oops: The switches are normally closed. So with the tap in the central position, assuming everything else is okay, with the ignition on there will be a path to earth through both switches via the sender's.

Sorry for any confusion I may have caused anyone.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

ScarboroughSeadog
Posts: 7
Joined: Tue Mar 07, 2023 4:06 pm

Re: Strange fuel gauge readings

Post by ScarboroughSeadog » Mon Mar 20, 2023 1:49 pm

Always good to finish these things off with a conclusion: replaced a faulty fuel gauge, replaced a faulty Lucas switch. All now working perfectly but there is an interesting issue with the senders. I have 3 senders marked TB1114-001W. This is the correct part number. One is brand new, one is say 10 years old, one is say 40 years old. Only the 40 year old one reads correctly (ie empty at empty). The other two newer ones read 1/8th at empty. I can only think the more modern parts have a different resistance scale? Fortunately with a repair made to a snapped spade connection I was able to use the original 40 year old part and all is working perfectly. Bit of a mystery though.

ScarboroughSeadog
Posts: 7
Joined: Tue Mar 07, 2023 4:06 pm

Re: Strange fuel gauge readings

Post by ScarboroughSeadog » Tue Mar 21, 2023 3:57 pm

Final thoughts after a helpful suggestion on another forum: These senders cover a few different set ups, and hence supply to different gauge decals etc. My particular (dated, less common) set up is an anomaly as far as these senders go. I suspect the sender is designed to work alongside a more modern gauge decal set up- with a red block 'empty' position which mine doesn't have.....

Post Reply