44AJ20 & 93KA28 Rebuild Barbados

Tell us about any of your Land Rover related projects here.
User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Door top alignment

Post by weetchus » Tue Oct 04, 2022 2:00 am

Hi all. How does one align a door top that goes straight up, with the upper bulkhead that is more or less vertical up to where the windscreen begins, then slants inward at about a 5 degree angle? This would require a kink in the door top and bent glass panes!

The green arrow is where it fouls against the windscreen frame.
16648448717874276060597476797828.jpg
16648448717874276060597476797828.jpg (1.81 MiB) Viewed 2068 times
Screenshot_20221003-205815.png
Screenshot_20221003-205815.png (2.3 MiB) Viewed 2068 times

User avatar
brinv8
Master Baker
Posts: 1121
Joined: Fri Jul 09, 2010 8:24 am
Location: Wendling, Norfolk

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by brinv8 » Tue Oct 04, 2022 4:12 pm

Been looking at your photos and something is not right, the top of the door (not window frame) should be somewhere near the top of the bulkhead, and the window frame should match into the top vent panel. The slight angle into the door opening is from the joint between the door and the window frame, the fixing studs are angled.

It looks like your door is fitted too low.

Photos of mine hopefully to give you an idea where the door should fit.

Thinking about this again, check your hinges, are they fitted correctly?
Attachments
Lwt door.2.jpg
Lwt door.2.jpg (74.51 KiB) Viewed 2054 times
Lwt door.1.jpg
Lwt door.1.jpg (64.94 KiB) Viewed 2054 times
Brian
56FL65 - LWT FFR 24v
61FL39 / 94AV44 - 101 RHD Radio Body 12v
55KL83 - Harley-Davidson MT350
- - - - - - - Can Am Bombardier 250

MalcolmR
Posts: 33
Joined: Thu Apr 23, 2020 10:31 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by MalcolmR » Tue Oct 04, 2022 4:49 pm

Think you may have the wrong frame.

MalcolmR
Posts: 33
Joined: Thu Apr 23, 2020 10:31 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by MalcolmR » Tue Oct 04, 2022 4:50 pm

Think you may have the wrong frame.

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by Loulou » Wed Oct 05, 2022 4:45 am

Hello Alex,

Good… provided that I understood the automatic translation of google and that I express myself in a clear way…

If you stand facing your LWT, you notice that the slope of the vertical pillars of the windshield is steeper than the slope of the vertical sheet metal at the rear in which the soft top slides and the rear part of the glazed area.
As you indicate, if these 2 verticals were parallel the glass surface would be twisted and the mobile window could not slide in the slide.
In addition, at the level of the windshield fixing, the nut (338240) presses on the inside of the angle of the glass area.
In the end it is the upper zone of the upper part of the glazed zone which "yawns" on the windscreen side and this remains a great classic of the LWT.

Reading MalcomR again, I seem to remember that there are 2 models of doors for the LWT (different heights) and as you work with 2 bodies to rebuild a vehicle…
See: https://www.paintmanpanels.co.uk/produc ... ghtweight/

Also the 4 hinges must be very flat and not press on the bulkhead.

Aligning the body, doors and upper glass parts of an LWT is a test for the nerves…

Good luck.
Looloo
Attachments
338240.png
338240.png (23.65 KiB) Viewed 2038 times
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Wed Oct 05, 2022 4:30 pm

Thanks LooLoo and MalcomR,

Here are a few more pics in case they help further. I think I might put another washer behind the bulkhead to chassis fixing bolts to increase the door gap very slightly. That is if the anti-burst door latch will still align with the corresponding catch. This may give a bit more freedom to the door and more space for the door top.

You can see in the pics that most of it all looks lined up quite well... I think. But let me know what you both think please.
Many thanks
Screenshot 2022-10-05 at 11.21.54 AM.png
Screenshot 2022-10-05 at 11.21.54 AM.png (2.35 MiB) Viewed 2027 times
Screenshot 2022-10-05 at 11.28.14 AM.png
Screenshot 2022-10-05 at 11.28.14 AM.png (2.82 MiB) Viewed 2027 times
Screenshot 2022-10-05 at 11.28.54 AM.png
Screenshot 2022-10-05 at 11.28.54 AM.png (3 MiB) Viewed 2027 times
Screenshot 2022-10-05 at 11.29.26 AM.png
Screenshot 2022-10-05 at 11.29.26 AM.png (2.72 MiB) Viewed 2027 times

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by Loulou » Thu Oct 06, 2022 8:30 am

Hello Alex,
Good… Not easy from a distance…

Below without taking into account the possible deformation of the camera lens.

1 - This is one of the most delicate points of the LWT; it's very long, very annoying and it will remain an alignment approximation
2 - Let's assume that the back (tub) is very correctly aligned
3 - Hinge fasteners do not appear to be aligned (red dotted line) with each other and with the door frame. Revise the holes in the door frame and/or add larger diameter screws (?)
4 - Is the axis alignment correct (yellow line)? See also the plastic rings in the female hinges if they are not too worn (I added rings cut from a Coke can to tighten the inside diameter)
5 - I have the impression that your bulkhead leans forward; perhaps review the squareness of it in relation to the chassis (blue dotted lines). You can adjust this alignment via the screw-unscrew rod that connects to the chassis-steering box plate. We talked about it in your previous posts.
6 - You installed bolts (pink circle) instead of countersunk screws = your male hinges may no longer be aligned with each other...

You have RHD and left door alignment issues; I have an LHD and the same problems with the right door = it's "logical" with an LWT… :oops: :mrgreen:

I accepted 5mm of non-alignment with my left door = This one is perfectly aligned with the bulkhead and the windshield but 5mm higher with the tube… 8-) :mrgreen:

And when you install new seals you can start all the alignment again by adding the recess or the protrusion of the door panel in relation to the side of the bodywork...

We keep calm and open a beer :D

Regards.
Looloo
Alex door.png
Alex door.png (2.68 MiB) Viewed 2006 times
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by AR4412 » Thu Oct 06, 2022 8:24 pm

Hi Alex,

Door alignment can be so much fun can't it? It appears that you have the bulkhead parts of the hinges the wrong way around, the taller pin should be at the top. Not that swapping them will help with the alignment in any way.

Have you got the packing piece/shim fitted behind the top bulkhead hinges? If not we the door bottom may be being pulled inwards at the top which won't help with the door top alignment as it may be hitting on the seal lip of the windscreen frame pushing out at the top. I needed to fit a couple to my lightweight, but I have fitted thicker door skins and have 90/110 door tops fitted.

It looks in the pic that the bottom door hinge appears to be bent. If it is, it will pull the bottom of the door forwards in relation to the top. The top door hinge piece appears to be new, and of the correct shape.

It can take a bit of perseverance, and bits of wood jammed in here and there whilst bolts are nipped up, to get the doors on a lightweight aligned . And that's before you resort to using the BFH to persuade things into alignment.

Good luck, you'll get there.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Sun Oct 09, 2022 12:06 am

I'm taking all your collective advice and working on it this weekend. Thanks very much. I'll update you next week.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Wed Oct 12, 2022 12:54 am

Okay guys. I have made some progress.
I loosened the bulkhead mounting bolts totally along with the floor panel to bulkhead screws, the steering shaft to bulkhead nuts on the inside of the cab, the chassis to bulkhead supports (vertical supports with three bolts and oblong holes + a bolt to secure the front wings to these. I also loosened up the grab handle shaft to these supports.

I then added spacer washers to increase the width of the door opening (i.e pushing the bulkhead forward. I struggled with the drivers side but the passenger side was easier when I cracked the door lower sill panel, having forgotten the bolt on the footwell side corner!!! Damn. More aluminium welding.

The doors fit a bit better but I need more width.
Could you please measure the door gap at the top and bottom of your doors if you get a chance?

On my d-side I have 800mm at the bottom (from bulkhead pillar to where the angle begins upwards at the rear) and 862mm at the top.

In the p-side I have 800mm at the bottom and 870mm at the top. I have read that I should have about 880mm at the top.

I'm relatively happy with the bulkhead squareness of the p-side see pic below.
The d-side is definitely sloping a bit towards the rear. Sorry about the pic, the space is cramped that side. How do I tilt the d-side forward more without the grab handle shaft?

Thanks!!

P-side
1665532045477664583429474581887.jpg
1665532045477664583429474581887.jpg (1.71 MiB) Viewed 1935 times
D-side
16655322567827573954270993853167.jpg
16655322567827573954270993853167.jpg (1.55 MiB) Viewed 1935 times

Post Reply