Bulkhead chassis outrigger.
-
nato potatoe
- Pastry Chef
- Posts: 504
- Joined: Tue Jul 06, 2010 10:23 pm
Bulkhead chassis outrigger.
Can anyone recommend a supplier for a bulkhead outrigger and a good quality fuel tank.
Cliff. (NATO Potato)
Cliff. (NATO Potato)
Re: Bulkhead chassis outrigger.
I recently bought a Bearmach fuel tank from these guys (note free delivery)
https://www.ebay.co.uk/itm/LAND-ROVER-S ... 2749.l2649
So far been impressed with it and I think it turned up within a day or two.
Rich
https://www.ebay.co.uk/itm/LAND-ROVER-S ... 2749.l2649
So far been impressed with it and I think it turned up within a day or two.
Rich
Rich aka Tricky
'72 SIII 12V GS Lightweight
Sankey
'72 SIII 12V GS Lightweight
Sankey
Re: Bulkhead chassis outrigger.
Hiya Cliff!
,
I have bought B###p##t fuel tanks for the Recce, (Don't tell anyone. But, as I got them at trade price it was rude not to.), and they actually look fairly decent. I think the Bearmach ones are okay too. Bulkhead outriggers can be a bit hit and miss depending who you get them from. Standard Series outriggers need shortening to fit and the ones I got from GDI Products advertised as for the lightweight chassis needed reworking to fit as there as too much meat on them outside of the bolt hole, meaning that they stuck out too far to be able to get the sill in place, and with the bulkhead bolt pushed through them for alignment they didn't touch my chassis. Personally I'd get a BP/Bearmach Series outrigger and cut it down by the required amount.
Regards,
I have bought B###p##t fuel tanks for the Recce, (Don't tell anyone. But, as I got them at trade price it was rude not to.), and they actually look fairly decent. I think the Bearmach ones are okay too. Bulkhead outriggers can be a bit hit and miss depending who you get them from. Standard Series outriggers need shortening to fit and the ones I got from GDI Products advertised as for the lightweight chassis needed reworking to fit as there as too much meat on them outside of the bolt hole, meaning that they stuck out too far to be able to get the sill in place, and with the bulkhead bolt pushed through them for alignment they didn't touch my chassis. Personally I'd get a BP/Bearmach Series outrigger and cut it down by the required amount.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: Bulkhead chassis outrigger.
Got my outriggers from Richards chassis
Perfect fit
Perfect fit
-
nato potatoe
- Pastry Chef
- Posts: 504
- Joined: Tue Jul 06, 2010 10:23 pm
Re: Bulkhead chassis outrigger.
Thanks for the replies guys will contact vendors and get availability.
Regards Cliff.
Regards Cliff.
Re: Bulkhead chassis outrigger.
I should have mentioned giving them a try, I got my rear crossmember from them, very helpful and a good price.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
faizanmazhar00
- Posts: 6
- Joined: Sun Feb 13, 2022 10:38 am
Re: Bulkhead chassis outrigger.
Welcomenato potatoe wrote: ↑Sat Apr 14, 2018 10:17 pmCan anyone recommend a supplier for a bulkhead outrigger and a good quality fuel tank.
Cliff. (NATO Potato)
Re: Bulkhead chassis outrigger.
A bit of a saga over bulkhead outriggers for LWTs... The ones supplied by GDI products are well made, but I found to be 5mm too short between the centre of the bolt hole and the chassis rail. I queried this with GDI (this was 3 years ago) and they told me that they had no problems or complaints and their dimensions were drawn from a Richard's chassis. I think that if you choose to just weld the replacement outrigger onto the outside of the rail, rather than letting it into the rail as I did, then you would see less of a discrepancy as you can allow 2 or 2.5mm for the thickness of the steel plate. I ended up cutting the outrigger and adding 5mm onto each side to line up correctly with the bulkhead.
- Attachments
-
- Outrigger extension 2 Before.jpg (288.04 KiB) Viewed 1611 times
-
- Outrigger extension 1.jpg (338.54 KiB) Viewed 1611 times
Re: Bulkhead chassis outrigger.
I found the GDI outriggers too short as well. I had cut out the rot behind the original and welded plates into the hole in the chassis siderail, and cut off the extensions from the outrigger intending to weld it on to look original, when I found it wouldn't line up with the outrigger bolt hole. My solution was to weld a plate the right thickness to the inside end of the outrigger.
Unfortunately, the addition of plates to the inside of the outriggers to align them with the bulkhead bolt holes meant that they stuck out too far past the bulkhead to allow for the sill to fit and had to be trimmed back.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: Bulkhead chassis outrigger.
Yes - I do expect to possibly have to adjust the outer length as well. It might fit, but it will be close.