44AJ20 & 93KA28 Rebuild Barbados

Tell us about any of your Land Rover related projects here.
User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Fri Sep 03, 2021 2:54 pm

Well put LooLoo. My wife's skills never cease to amaze me.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

DIY Starter Handle Brackets: Dimensions

Post by weetchus » Fri Sep 03, 2021 8:11 pm

If anyone wants to make the starter handle brackets like mine, here is an image of the bracket and the design drawing with dimensions.
Note that the big hole through the centre is smaller than it needs to be as I left room for filing back the hole to fit varying sized starter handle thicknesses.

Any questions, just shout.
Screenshot 2021-09-03 at 3.01.56 PM.png
Screenshot 2021-09-03 at 3.01.56 PM.png (2.53 MiB) Viewed 2121 times
Screenshot 2021-09-03 at 3.01.41 PM.png
Screenshot 2021-09-03 at 3.01.41 PM.png (2.68 MiB) Viewed 2121 times
Screenshot 2021-09-03 at 3.05.33 PM.png
Screenshot 2021-09-03 at 3.05.33 PM.png (1.35 MiB) Viewed 2121 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Headlights

Post by weetchus » Tue Nov 02, 2021 5:29 pm

Thanks Fred for your Headlights guide. Super useful as finding this info for Lightweights is hard.
Here is Fred's guide viewtopic.php?f=6&t=4841&hilit=23HF14&s ... start=1120

I have replaced a few rivnuts and screws on mine as they broke getting them out. Quite a challenge as modern rivnuts seem to not have the larger outside diameter to smaller internal diameter that the originals have. One happy coincidence is that a bicycle Schrader valve cap fits nicely on the rivnut end!
Screen Shot 2021-11-02 at 1.19.21 pm.png
Screen Shot 2021-11-02 at 1.19.21 pm.png (3.08 MiB) Viewed 2094 times
Screen Shot 2021-11-02 at 1.19.32 pm.png
Screen Shot 2021-11-02 at 1.19.32 pm.png (1.47 MiB) Viewed 2094 times
Screen Shot 2021-11-02 at 1.19.45 pm.png
Screen Shot 2021-11-02 at 1.19.45 pm.png (1.2 MiB) Viewed 2094 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

IR Headlights Switch

Post by weetchus » Tue Nov 02, 2021 5:36 pm

For the purists out there... avert your eyes.
I made an IR switch to fill the hole in the small panel.
Personally, I like it a lot. Was thinking I could hook it up to run a rear spot light or maybe label it 'Ejector Seat' as I have seen one other do. I have all the connections for IR... but want to get the truck running before I start wasting time doing unnecessary but fun future jobs. Anyone have IR set up? Interested to know what is involved. Do I have to drive with night vision goggles at night for them to be effective? haha :lol:
Screen Shot 2021-11-02 at 1.32.52 pm.png
Screen Shot 2021-11-02 at 1.32.52 pm.png (894.69 KiB) Viewed 2094 times
Screen Shot 2021-11-02 at 1.33.33 pm.png
Screen Shot 2021-11-02 at 1.33.33 pm.png (1.61 MiB) Viewed 2094 times
Screen Shot 2021-11-02 at 1.32.39 pm.png
Screen Shot 2021-11-02 at 1.32.39 pm.png (852.58 KiB) Viewed 2094 times

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by Loulou » Wed Nov 03, 2021 7:35 am

Hi Alex,

Is MacGuyver back…?

Bravo for these tips which open to solutions.

Regards.
Looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Thu Nov 04, 2021 3:22 pm

Haha.
Yep, my fabrications always come with a patina even when they are new. I am not cut out to do perfectionist work (with no scratches and dents) which is why Land Rovers are perfect for me and why I like them anyway.
Loulou wrote: ↑
Wed Nov 03, 2021 7:35 am
Hi Alex,

Is MacGuyver back…?

Bravo for these tips which open to solutions.

Regards.
Looloo

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Spool Gun Welding and Painting

Post by weetchus » Tue Dec 07, 2021 6:02 pm

Have not updated for a long time... I've been busy on the birmabright cracks... learning to suck at welding with a spool gun.
It is literally impossible. Here is my process... perhaps someone out there knows some better tricks.

What I knew about before I started and measures I took:
The material is so thin, you blow through all the time - so I would clamp a thick piece of steel bar behind the place I was welding to help dissipate the heat.
The wire piles up into towers or lumps - so I use a blow torch to pre-heat the aluminium before welding.
The torch angle should be push - on this stuff, it makes no difference. The results always suck.
The stickout should be 3/4 inch - sort of helps...
Spot welds are basically impossible.
Play with the settings - I dialled up, down, left and right... got it to a place where the results were less awful.

Here is a typical weld... bar behind the crack clamped in place. Everything shining clean. Acetone wipe the area. blow torch heat the surfaces. 3/4 stick out. Try to get a welding puddle. Huge blob build up. Spend 20 mins grinding down a mess to get 4 seconds of welding cleaned up.
This trial and error process has helped me get all the cracks fixed... but it was not fun.

Now I am onto painting.

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Spool Gun Welding and Painting

Post by weetchus » Tue Dec 07, 2021 6:05 pm

Here are some shots of the 'paint room'
Screen Shot 2021-12-07 at 1.46.22 pm.png
Screen Shot 2021-12-07 at 1.46.22 pm.png (1.66 MiB) Viewed 2023 times
The bits I have been dying to paint for 3 years.
Screen Shot 2021-12-07 at 1.46.29 pm.png
Screen Shot 2021-12-07 at 1.46.29 pm.png (1.86 MiB) Viewed 2023 times
Doors all primed
Screen Shot 2021-12-07 at 1.46.47 pm.png
Screen Shot 2021-12-07 at 1.46.47 pm.png (2.91 MiB) Viewed 2023 times
Tub and seatbox all primed
Screen Shot 2021-12-07 at 1.46.39 pm.png
Screen Shot 2021-12-07 at 1.46.39 pm.png (1.73 MiB) Viewed 2023 times

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by Loulou » Wed Dec 08, 2021 5:27 pm

Hi Alex,

Well, it's progressing ...
Carefully degrease the aluminum beforehand and a good bonding primer before painting.
Also insulate your steel door structures from the aluminum skin (plastic sheet in between or putty) so as not to have catalytic corrosion; Ditto for the rear fixing brackets of the tub with the frame. In short, any contact between steel and aluminum.

For aluminum welding ... hehe, I struggled a lot on this file and in the end I had a (real) pro do it; the cost was more than worth my disappointment. It's a job.

Good luck for the future.

Regards.
Looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Fri Dec 10, 2021 7:32 pm

Thanks LooLoo.
I'm doing all you suggest and recycling HDPE plastic milk container plastic in the spirit of saving the planet. Got to do something positive to balance the fuel inefficient LWT!
Happy Xmas to you and family and a million thanks for your continuous help and advice.
Alex

Loulou wrote: ↑
Wed Dec 08, 2021 5:27 pm
Hi Alex,

Well, it's progressing ...
Carefully degrease the aluminum beforehand and a good bonding primer before painting.
Also insulate your steel door structures from the aluminum skin (plastic sheet in between or putty) so as not to have catalytic corrosion; Ditto for the rear fixing brackets of the tub with the frame. In short, any contact between steel and aluminum.

For aluminum welding ... hehe, I struggled a lot on this file and in the end I had a (real) pro do it; the cost was more than worth my disappointment. It's a job.

Good luck for the future.

Regards.
Looloo

Post Reply