19j.engineo.rings.causing.low.oil.pressure

If you have encountered or solved a problem post here
Post Reply
aerialphil
Posts: 136
Joined: Sun Apr 22, 2012 12:43 pm

19j.engineo.rings.causing.low.oil.pressure

Post by aerialphil » Sun Jul 04, 2021 6:58 pm

Hi.all,
I.am.rebuilding.a.19j.engine.
I.read,that,there,are,2,o,ring,in,the,cam,drive,gear,,to,the,oil,pump,that.go.hard.and.cause.low.oil.pressure
I.have.found.one,of,these,in.the.midlle.of.the,grooved.thick.washer.,but,does,anyone,know,
where,the,other,one,is,Phil

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: 19j.engineo.rings.causing.low.oil.pressure

Post by AR4412 » Sun Jul 04, 2021 7:51 pm

Hi Phil,

There is an O-ring seal on the inside of the seal collar, (Or, grooved thick washer as you named it.), at the top of the skew gear, there is also one on the outside of that collar. You need to remove the circlip and take the collar out to change the outer seal. There is another O-ring on the strainer where it fits into the pump body.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

aerialphil
Posts: 136
Joined: Sun Apr 22, 2012 12:43 pm

Re: 19j.engineo.rings.causing.low.oil.pressure

Post by aerialphil » Sun Jul 04, 2021 9:07 pm

Hi,thanks,for,the,reply,So.one.on.inside.of.grooved.washer.and.one.on.the.outside.of.the.washer..Having,difficulty,understanding,the,location.of.th.one.on.the.strainer.of.the.pump?Phil

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: 19j.engineo.rings.causing.low.oil.pressure

Post by AR4412 » Sun Jul 04, 2021 9:19 pm

Where the strainer tube goes into the body of the pump there is a union, the O-ring is in there to seal it. You need to remove the strainer to get to it. The union is held with a lock tab washer to stop it coming undone, so you need to bend the tabs back to undo it.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

aerialphil
Posts: 136
Joined: Sun Apr 22, 2012 12:43 pm

Re: 19j.engineo.rings.causing.low.oil.pressure

Post by aerialphil » Sun Jul 04, 2021 9:30 pm

Sorry,but,this,word,strainer,?.I,assume.we.are.talking.about.the.vacuum.pump.

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: 19j.engineo.rings.causing.low.oil.pressure

Post by AR4412 » Sun Jul 04, 2021 9:50 pm

The strainer is on the end of the oil pump pick up pipe in the sump. It's the first line of defence in keeping crud out of the lubrication system. On poorly maintained engines it can block up, leading to oil starvation.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

aerialphil
Posts: 136
Joined: Sun Apr 22, 2012 12:43 pm

Re: 19j.engineo.rings.causing.low.oil.pressure

Post by aerialphil » Sun Jul 04, 2021 9:59 pm

Ah..got.it.thanks.Phil

aerialphil
Posts: 136
Joined: Sun Apr 22, 2012 12:43 pm

Re: 19j.engineo.rings.causing.low.oil.pressure

Post by aerialphil » Mon Jul 05, 2021 9:13 pm

Had.a.close.look.at.the.washer.and.there.were.only.hard.small.bits.of.the.washer.left.on.the.inner.side.and.the.outer.one.was.in.5.pieces.and.very.hard..This.will.be.a.common.cause.of.low.oil.pressure.and.the.flickering.oil.light.at.tickover.It.was.very.easy.to.
change.lifted.the.circlip.out.with.pliers.and.then.the.thick.washer.Many.thanks.for.the.reply.Phil

Post Reply