Override mechanism, groove

Discuss problems here
Post Reply
Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Override mechanism, groove

Post by Fossibear » Mon Jan 25, 2021 8:03 am

CBBDBDFF-2F02-40A0-9243-8DE8D29FC165.jpeg
CBBDBDFF-2F02-40A0-9243-8DE8D29FC165.jpeg (93.92 KiB) Viewed 12711 times
in front of the override mechanism there is a groove as shown in the picture.
Can someone tell me please, whether there was something in it like an o- ring or so?
After I pulled out the draughteye I found there only lots of rust...

Kindly regards, Steve
It's supposed to look like that, it's crochet...

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: Override mechanism, groove

Post by fv1620 » Mon Jan 25, 2021 10:29 am

I think you are seeing the cross-sectional view of the circumferential groove for a seal.
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Override mechanism, groove

Post by Fossibear » Mon Jan 25, 2021 10:49 am

yes, ok, but of what kind was the seal if there was one in there?
Was it rubber?

Regards, Steve
It's supposed to look like that, it's crochet...

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: Override mechanism, groove

Post by fv1620 » Mon Jan 25, 2021 11:09 am

Steve if you tell me the full nomenclature of the trailer I may be able to give you the part number & even cross reference it to specified dimensions.

If you can do that it will save me time looking through lots of trailer parts lists.
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Override mechanism, groove

Post by Fossibear » Mon Jan 25, 2021 5:06 pm

Hi Clive,

it’s my Sankey NT from about 1968.

Regards, Steve
It's supposed to look like that, it's crochet...

User avatar
Bob Fell
Cake Guru
Posts: 3044
Joined: Wed Sep 18, 2013 7:17 am
Location: Melton Mowbray

Re: Override mechanism, groove

Post by Bob Fell » Mon Jan 25, 2021 7:21 pm

Fossibear wrote: ↑
Mon Jan 25, 2021 10:49 am
yes, ok, but of what kind was the seal if there was one in there?
Was it rubber?

Regards, Steve
Steve,
The front draught eye seal is felt, part no. FV491002 0.22in w x 0.156 in thk x 5.8 in lg according to the parts manual (but think that should read 0.58 in?),then the one behind the washer key is synthetic rubber 1-5/8in id x 1/8 h(?), no part no. listed. Unobtainable I believe but did see some NOS a couple of years back on gleebay. Clive will hopefully come up with something equivalent (Hi Clive, hope you are keeping well and on air in deepest darkest Wales).
Cheers,
Bob
042Bobf


19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Override mechanism, groove

Post by Fossibear » Mon Jan 25, 2021 7:42 pm

Hi Bob,
thank you very much - perhaps Clive is able to confirm...

Than I am closer to get my Sankey on the road back again.

Stay safe, Steve
It's supposed to look like that, it's crochet...

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: Override mechanism, groove

Post by fv1620 » Mon Jan 25, 2021 11:46 pm

Yes I agree with Bob I think the felt seal should be 0.58 in long
There is a Rubery Owen part number RDSK10222

As for the ring, quite a few part numbers including RAF, RN, as well as Army & a couple of manufacturers.
Trailer ring.jpg
Trailer ring.jpg (77.08 KiB) Viewed 12653 times
(Bob yes on air quite a lot. Had CW contacts today on 80m & 2m, then tonight FM on 4m. Looking forward to tomorrow as heavy rain forecast so I should get out from the valley on 3cm using rain scatter)
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Override mechanism, groove

Post by Fossibear » Tue Jan 26, 2021 6:51 pm

:D

Thanks to you both - then I’ll try to get it.
Yesterday I was in a MOT point and spoke to the guy who will give me the admittance to use my Sankey on public roads in a allowed way.
We found a way and now I have to work it out.
When it’s ready I’ll show here - to complicated to describe it though it very easy at last...

Regards, Steve
It's supposed to look like that, it's crochet...

Post Reply