Lightweight too high for garage....help!
Lightweight too high for garage....help!
I have a vertically challenged up and over door on my lockup garage. Will a Lightweight Land Rover fit? The height I have to clear the door is 1.81m and I know that is about 0.15m too low according to the max dimensions listed on the net. But is it possible to partially dismantle the tilt - lower the load bay hoops - and have clearance? I know I could dismantle the lot - rainwater channels over doors, lower screen, etc, but that is a heck of a job just to get it in and out. What is the lowest height that can be easily achieved with a bit of quick spanner work? Can some kind soul measure up on their truck for me? I would be v grateful. Thanks!
-
Farmer Neil
- Posts: 33
- Joined: Sun Mar 08, 2020 3:00 pm
- Location: Loughborough
Re: Lightweight too high for garage....help!
Hi ,
Here are a few piccys of my new garage and my Lightweight. Its on 6.5-16 wheels . My door is 2.01m high and there isn't a whole load of clearance. My actual height is 196cm to top of tilt.
if you would like me to measure anything else I can do so if it helps.
Cheers Neil
Here are a few piccys of my new garage and my Lightweight. Its on 6.5-16 wheels . My door is 2.01m high and there isn't a whole load of clearance. My actual height is 196cm to top of tilt.
if you would like me to measure anything else I can do so if it helps.
Cheers Neil
- Attachments
-
- landy3.JPG (294.61 KiB) Viewed 2372 times
-
- landy 2.JPG (220.11 KiB) Viewed 2372 times
-
Farmer Neil
- Posts: 33
- Joined: Sun Mar 08, 2020 3:00 pm
- Location: Loughborough
Re: Lightweight too high for garage....help!
A couple more measurements
- Attachments
-
- landy5.JPG (335.4 KiB) Viewed 2368 times
-
- landy4.JPG (249.92 KiB) Viewed 2368 times
Re: Lightweight too high for garage....help!
Neil - thats brilliant - just what I needed to know. I was advised that its a five minute job to temporarily lower the hoops and back of the rainwater channels so that the highest part is over the windscreen - and your tape measure gave me that exactly and it shows there are a few cm to spare AND I have the option to drop tyre pressure. It will fit!! Thanks ever so. Ferg
Re: Lightweight too high for garage....help!
We had a double decker bus stuck under a bridge near here some years ago - jammed good and proper. All the emergency services were standing around wondering how to extract it. It was my mother who asked them the obvious - why don't you just let the tyres down?
Not ideal on regular basis for a garage though, but much easier than taking tilt and hoops off. If they are fitted properly, that's more than five minutes! Also - your height will be affected by which tyres you have fitted and also any spring upgrades (parabolics etc).
We used to service National River Authority Quadtech Defenders (big box bodies which wouldn't fit through the workshop door). For some reason, and I never understood why, it was always me who was asked to stand on the tow bar and hang on while it was driven in to the workshop. Was I really the fattest person in the workshop? I deny all - its just that my chest has slipped a bit.
Not ideal on regular basis for a garage though, but much easier than taking tilt and hoops off. If they are fitted properly, that's more than five minutes! Also - your height will be affected by which tyres you have fitted and also any spring upgrades (parabolics etc).
We used to service National River Authority Quadtech Defenders (big box bodies which wouldn't fit through the workshop door). For some reason, and I never understood why, it was always me who was asked to stand on the tow bar and hang on while it was driven in to the workshop. Was I really the fattest person in the workshop? I deny all - its just that my chest has slipped a bit.
Re: Lightweight too high for garage....help!
I had similar problem when I owned mine.
Caught the canvas and put a small tear in it.
Ended up getting electric doors which gave me much more height
Caught the canvas and put a small tear in it.
Ended up getting electric doors which gave me much more height
-
Poacher3536
- Posts: 54
- Joined: Wed Oct 24, 2018 8:18 pm
- Location: Peterborough
Re: Lightweight too high for garage....help!
I’ve got the same exact problem. My garage door is electric and when it opens the door folds back on itself taking around 2 inches off the height.
The only way to get my LW in is to take lots of air out the rear tyres and then re-inflate once inside.
I’ve looked at loads of different option to solve this:
Creating two recessed track marks from outside to inside the garage but the wife says no.
Adjusting the door - already at its maximum adjustment.
The only real solution is to take out the electric door completely and install a side sliding door.
The only way to get my LW in is to take lots of air out the rear tyres and then re-inflate once inside.
I’ve looked at loads of different option to solve this:
Creating two recessed track marks from outside to inside the garage but the wife says no.
Adjusting the door - already at its maximum adjustment.
The only real solution is to take out the electric door completely and install a side sliding door.
20HF23 - 1980 Series III FFR lightweight - now 200TDI/12v
Re: Lightweight too high for garage....help!
My eclectic doors extract into a box that sits above the opening
Re: Lightweight too high for garage....help!
My quick and simple solution to the Lightweight not fitting in the garage was to buy a car cover and leave it outside under that. The added bonus to that solution is more storage space for the bits of the other project Lightweight.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: Lightweight too high for garage....help!
I have the issue that the ramp up to my garage means the rear hood hits the top of the garage door frame due to the angle of attack.
It would be fine if it the entrance to the garage was level.
So i just drop the hood sticks down out of their sockets at the rear everytime i reverse in.
Drive out lift the rear hood sticks back into the sockets and off I go.
It would be fine if it the entrance to the garage was level.
So i just drop the hood sticks down out of their sockets at the rear everytime i reverse in.
Drive out lift the rear hood sticks back into the sockets and off I go.