Ah ok they are bolts not studs eh? Every day is a school day thanks buddy. Mine are deffo threaded but maybe they just picked up the thread over the years. I picked a 9mm ID but 12mm OD so plenty of wiggle room matey.AR4412 wrote: ↑Sun May 31, 2020 6:33 pmOh. Right there Ted. Do you mean the ones for the bolts on the 'feet' of the vent panel to pass through, highlighted below?
SAM_1813.JPG
The four tubes are plain, Just measured mine and they work out at around 9.25/9.3 mm in new money, so 9mm might be enough, but a blast through with a 9.5 mm drill bit shold see you with enough leeway to get all the bolts through with some wriggle room for alignment.
Regards,
Monty the rather rusty 2A - 37FG31
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Re: Monty the rather rusty 2A - 37FG31
I meant to add in my last post that the four bolts are also 5/16" UNF, 2 3/4" long-uns.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Duly noted squadron leader, I’ll add to the list. Hopefully I’ll have a new lower door next week to begin the fascinating sport of gap alignment - watch this space!
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
So, last night I made up a missing door hinge spacer after having been reminded on Howard’s thread
.. and then the fun began on the 6-way switch. So since getting the landy there has been this issue that it won’t retain the lock barrel in the 6-way switch. I suspected having shone a torch down the recess, that the plastic receiver was damaged.. so as the switch needs a clean up overall, might as well go for a full strip down and see if it can be fixed..
I was a bit hesitant to pry apart the two halves as I was worried the tabs would snap, but it came apart pretty easily with the application of a thin bladed screwdriver..
Not too bad inside in terms of corrosion on the contacts. Should clean up nicely..
.. and then the fun began on the 6-way switch. So since getting the landy there has been this issue that it won’t retain the lock barrel in the 6-way switch. I suspected having shone a torch down the recess, that the plastic receiver was damaged.. so as the switch needs a clean up overall, might as well go for a full strip down and see if it can be fixed..
I was a bit hesitant to pry apart the two halves as I was worried the tabs would snap, but it came apart pretty easily with the application of a thin bladed screwdriver..
Not too bad inside in terms of corrosion on the contacts. Should clean up nicely..
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
So from the below you can see the offending item. It’s snapped off for about half of the circumference from the front to about halfway back. I’m guessing this sits several rows up from unobtanium on the mystical shelves of the great parts warehouse in the sky. Damn. Does anyone have an old 2a-spec 6-way switch with this part intact?
Here you can see it with the barrel in situ to get a better idea of how it functions..
..and below how it fits into the back of the casing...
...I then had to prove to myself that I could get it all back together again..
So for now it’s all stored away waiting for that rare part. Maybe I’ll try plastic cement, or epoxy to repair it... or maybe get a mate to turn one on his lathe.
There was also a bit of a chip to the outer plastic collar, where the hole for the steel sprung retaining pin that stops the plastic knob being removed had been snapped. I’ve managed to glue that back together, so hooray for one easy fix.
I’ll do a more detailed rebuild guide once I have the part I need, as I suspect there are a fair few people out there who will need to fix their switch at some point.
All the best,
Andy
Here you can see it with the barrel in situ to get a better idea of how it functions..
..and below how it fits into the back of the casing...
...I then had to prove to myself that I could get it all back together again..
So for now it’s all stored away waiting for that rare part. Maybe I’ll try plastic cement, or epoxy to repair it... or maybe get a mate to turn one on his lathe.
There was also a bit of a chip to the outer plastic collar, where the hole for the steel sprung retaining pin that stops the plastic knob being removed had been snapped. I’ve managed to glue that back together, so hooray for one easy fix.
I’ll do a more detailed rebuild guide once I have the part I need, as I suspect there are a fair few people out there who will need to fix their switch at some point.
All the best,
Andy
Re: Monty the rather rusty 2A - 37FG31
Hiya Andy!
,
The ignition barrel internals are also in the Series III 6 way switch. It's just the knob that is different. Pretty sure the electrics on the rear are the same, but can check mine tonight after work.
Regards,
The ignition barrel internals are also in the Series III 6 way switch. It's just the knob that is different. Pretty sure the electrics on the rear are the same, but can check mine tonight after work.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Thanks buddy - odd that they never deleted the barrel receiver but I guess maybe it was just cheaper not to redesign it, and just whack a new knob on it, as it were.
Appreciate you looking as always.
Andy
Re: Monty the rather rusty 2A - 37FG31
Andy,
Fred gave me an old switch that I needed a few parts off for mine. Will get round to looking at that in a week or two, it may have the part you need which you will be welcome to.
Cheers,
Howard
Fred gave me an old switch that I needed a few parts off for mine. Will get round to looking at that in a week or two, it may have the part you need which you will be welcome to.
Cheers,
Howard
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
That would be magic thanks Howard - if you still have both the inner and outer black plastic parts (not the knob, the bits behind it) I’d be interest in both. As I said I glued the outer bit - but ideally would replace that too. It’s the black plastic bit on the right in this photo..
As with Neil - thanks for your help with this.
Andy
Re: Monty the rather rusty 2A - 37FG31
Just to be safe, I took the nob off my six way switch. The internals are there, and when turned to ignition on, the two central 'ignition' teminals are joined.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.