Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu May 14, 2020 6:45 pm

AR4412 wrote: ↑
Thu May 14, 2020 8:04 am
Fred wrote: ↑
Wed May 13, 2020 7:47 pm
All we need now is Neil to be beavering away on his para recce and all will be well in the world
Hopefully soon Fred. The only lightweight I get to work on at present is the back burner project one at work if I run out of customer work at the end of the day.
andrewjsimpson1977 wrote: ↑
Wed May 13, 2020 7:59 pm
and I agree on the Neil point, although in his defence he’s reliant on the blasters being open.
Hopefully they will re-open soon and I can re-book the chassis to be done.

For now I have to make do with tinkering at work and following the projects on here. So keep the updates coming Andy!

Regards,
Right you are Sarge 😎

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Thu May 14, 2020 7:22 pm

Good lad.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu May 14, 2020 9:55 pm

Sorry for the rubbish photo... this was taken on my lunch break. I decided early on in the day to park the landy outside the front door (because Mrs S is a kind and tolerant person like that ;) ) so I could nip out here and there when I got five minutes.

A301BCA5-3363-499D-8E97-521A9EE01CD4.jpeg
A301BCA5-3363-499D-8E97-521A9EE01CD4.jpeg (1.61 MiB) Viewed 1724 times
Today I trimmed the excess steel from the centre panel (where the heater goes) on the bulkhead, and generally straightened up the fascia with the old metal tickling hammer. Apart from a disappointing amount of surface rust (to be dealt with by Colonel Sander and his friend E Vaporust this weekend) the bulkhead has survived the winter pretty well. There’s still some welding to be done to complete the dash boxes, and the little L plates at the tops of the footwells where they meet the goalpost legs need adding but I think that’s all minor compared to the work that’s been done so far, so it’s a bit less daunting now.


I also removed the remnants of the cut off sender of the water temp capillary bulb thingy from the head, and replaced with (NON ORIGINAL SPEC PARTS ALERT) an electric sender from series 3. Calm down though, (especially you Bob stop raging at the monitor :D ) , all will be replaced in good time. I’m just not paying the current going rate of 150 quid for a copper tube full of ether, when one will no doubt show up at a parts fair when the zombie apocalypse is over. I have an electric s3 temp gauge on the way and this setup will be used for now to give me some confidence in running the engine when the time comes.

I’m generally building the truck up now, so I can see what’s missing before final rub down and paint. I’ve already loosely fitted the pedal towers, and will have a look at cutting the hole for the steering column once I can remember what I’ve done with Fred and Neil’s measurements.

I would have got some more done this evening but my neighbour has encouraged a higher than usual alcohol input, on the grounds that it helps with my mental wellbeing. Or at least that’s what I’ve told Sara.

All the best,

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat May 16, 2020 8:13 pm

More tinkering today, mostly lining up the pieces of the cabin, and trying to bash the gearbox tunnel vanity panel into the right shape so that the edges meet the floor properly. Also lots of scrubbing the thin layer of winter rust off the bulkhead..

EC669153-24B6-4129-B9B3-35DD76A5BEEB.jpeg
EC669153-24B6-4129-B9B3-35DD76A5BEEB.jpeg (1.39 MiB) Viewed 1693 times
A4CB0A2D-B931-4EFF-B07C-6C963A9D112A.jpeg
A4CB0A2D-B931-4EFF-B07C-6C963A9D112A.jpeg (1.43 MiB) Viewed 1693 times

I also made a start on fitting the steering column by drilling the four mounting holes for the bracket. Thanks again to Fred and Neil for the measurements, which somehow only made sense once I’d bitten the bullet and drilled and mounted the bracket, but still - the pilot hole I drilled in the middle is aligned with the gap between the pedal towers, so all is well. Tells me as a para wan learner I should trust in the teachings of wiser masters. I would have drilled the big hole for the column itself but my bigger drill (with the wider chuck) that fits the step drill bit has died over the winter, so I’ve borrowed my neighbour’s one - but it’s now too late and I want a beer so that will get done tomorrow, along with the other dashboard holes, and the ones in the footwell side panels for the fuel tap and headlight foot switch cable.

I silver soldered the oil cooler pipe I made up last year, which was a nice easy job and amazingly I didn’t set fire to myself or anything else, so that’s got to be some sort of personal record.

5E324071-DD96-450C-825E-E54DBB5A248F.jpeg
5E324071-DD96-450C-825E-E54DBB5A248F.jpeg (777.37 KiB) Viewed 1693 times

C9DB09CD-136F-46F4-9920-89B72CB7A202.jpeg
C9DB09CD-136F-46F4-9920-89B72CB7A202.jpeg (1.28 MiB) Viewed 1693 times

Finally, I did manage to drill the holes for the accelerator linkages, which were test fitted along with the brake and clutch pedals. I’m basically one column hole away from being able to fit the steering wheel, and give it some Toad of Toad Hall action on the driveway.


“Brrrrrm Brrrrrmm”


All the best,

Andy

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Sat May 16, 2020 10:38 pm

andrewjsimpson1977 wrote: ↑
Sat May 16, 2020 8:13 pm
More tinkering today, mostly lining up the pieces of the cabin, and trying to bash the gearbox tunnel vanity panel into the right shape so that the edges meet the floor properly. Also lots of scrubbing the thin layer of winter rust off the bulkhead..


EC669153-24B6-4129-B9B3-35DD76A5BEEB.jpeg


A4CB0A2D-B931-4EFF-B07C-6C963A9D112A.jpeg


I also made a start on fitting the steering column by drilling the four mounting holes for the bracket. Thanks again to Fred and Neil for the measurements, which somehow only made sense once I’d bitten the bullet and drilled and mounted the bracket, but still - the pilot hole I drilled in the middle is aligned with the gap between the pedal towers, so all is well. Tells me as a para wan learner I should trust in the teachings of wiser masters. I would have drilled the big hole for the column itself but my bigger drill (with the wider chuck) that fits the step drill bit has died over the winter, so I’ve borrowed my neighbour’s one - but it’s now too late and I want a beer so that will get done tomorrow, along with the other dashboard holes, and the ones in the footwell side panels for the fuel tap and headlight foot switch cable.

I silver soldered the oil cooler pipe I made up last year, which was a nice easy job and amazingly I didn’t set fire to myself or anything else, so that’s got to be some sort of personal record.


5E324071-DD96-450C-825E-E54DBB5A248F.jpeg



C9DB09CD-136F-46F4-9920-89B72CB7A202.jpeg


Finally, I did manage to drill the holes for the accelerator linkages, which were test fitted along with the brake and clutch pedals. I’m basically one column hole away from being able to fit the steering wheel, and give it some Toad of Toad Hall action on the driveway.


“Brrrrrm Brrrrrmm”


All the best,

Andy
I hope your soldering is better than mine, my home made pipe has been added to the snagging list as it leaks at the thermometer pocket end....and that is only from me turning the engine over!
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat May 16, 2020 11:14 pm

landylees wrote: ↑
Sat May 16, 2020 10:38 pm
andrewjsimpson1977 wrote: ↑
Sat May 16, 2020 8:13 pm
More tinkering today, mostly lining up the pieces of the cabin, and trying to bash the gearbox tunnel vanity panel into the right shape so that the edges meet the floor properly. Also lots of scrubbing the thin layer of winter rust off the bulkhead..


EC669153-24B6-4129-B9B3-35DD76A5BEEB.jpeg


A4CB0A2D-B931-4EFF-B07C-6C963A9D112A.jpeg


I also made a start on fitting the steering column by drilling the four mounting holes for the bracket. Thanks again to Fred and Neil for the measurements, which somehow only made sense once I’d bitten the bullet and drilled and mounted the bracket, but still - the pilot hole I drilled in the middle is aligned with the gap between the pedal towers, so all is well. Tells me as a para wan learner I should trust in the teachings of wiser masters. I would have drilled the big hole for the column itself but my bigger drill (with the wider chuck) that fits the step drill bit has died over the winter, so I’ve borrowed my neighbour’s one - but it’s now too late and I want a beer so that will get done tomorrow, along with the other dashboard holes, and the ones in the footwell side panels for the fuel tap and headlight foot switch cable.

I silver soldered the oil cooler pipe I made up last year, which was a nice easy job and amazingly I didn’t set fire to myself or anything else, so that’s got to be some sort of personal record.


5E324071-DD96-450C-825E-E54DBB5A248F.jpeg



C9DB09CD-136F-46F4-9920-89B72CB7A202.jpeg


Finally, I did manage to drill the holes for the accelerator linkages, which were test fitted along with the brake and clutch pedals. I’m basically one column hole away from being able to fit the steering wheel, and give it some Toad of Toad Hall action on the driveway.


“Brrrrrm Brrrrrmm”


All the best,

Andy
I hope your soldering is better than mine, my home made pipe has been added to the snagging list as it leaks at the thermometer pocket end....and that is only from me turning the engine over!

Well that’s worrying. I had several passes filling up the gap with solder until I ran out so hopefully it’s a good seal, but I’m sure time will tell. How’s life treating you buddy? You’ll notice from the clamps in the photos that some of my spot welds have let go (no doubt a result of me rushing it last minute) but I have a new set of ‘spot weld tips’ for my MIG so hopefully that / tigerseal will prevail.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun May 17, 2020 3:33 pm

Three hours to fit and roughly adjust the rest of the steering system, at least the test department was pleased..

21889B85-24F6-4857-A6F4-C91D77A59575.jpeg
21889B85-24F6-4857-A6F4-C91D77A59575.jpeg (1.29 MiB) Viewed 1653 times
98F9FD1D-6338-470C-8656-935A7AE6EA38.jpeg
98F9FD1D-6338-470C-8656-935A7AE6EA38.jpeg (1.89 MiB) Viewed 1653 times
ED73E13C-2708-4A82-B14B-E98654D04A58.jpeg
ED73E13C-2708-4A82-B14B-E98654D04A58.jpeg (1.11 MiB) Viewed 1653 times
AC07D8E9-37EF-46C6-8288-163D6BB20A48.jpeg
AC07D8E9-37EF-46C6-8288-163D6BB20A48.jpeg (1.31 MiB) Viewed 1653 times

Beer time!

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Monty the rather rusty 2A - 37FG31

Post by Fossibear » Sun May 17, 2020 4:04 pm

I don’t hope for the driver :D
It's supposed to look like that, it's crochet...

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sun May 17, 2020 6:37 pm

D'you know, it's really good to see this restoration on the go again. It looks really great there in the sunshine and lovely to see your son interested in it, though, I agree with Steve, he's going to need more than a crash helmet to drive the thing! But, in so many ways, I so miss working on mine. I have enjoyed fiddling with the Discovery, but i know I don't have the skills to do it real justice. And today I spent a very fruitless afternoon, trying to open Freda's Freelander tailgate. It's jammed shut. The electrics work, the window does its wind-down stuff, the other doors work on the central locking, but not the tailgate. And... the best bit of advice on a Freelander forum is that - to free the lock you need to open the door! Brilliant. I wish I'd thought of that.

Fossibear
Posts: 430
Joined: Sun Nov 18, 2018 1:20 pm
Location: Nordkirchen / Germany

Re: Monty the rather rusty 2A - 37FG31

Post by Fossibear » Sun May 17, 2020 7:43 pm

@Fred: the window- lifter in a Freelander with its wires and so on is witchcraft. The problem with mine a few years ago was rusty wires...
It's supposed to look like that, it's crochet...

Post Reply