Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Tue May 19, 2020 9:19 pm

I wish you'd said about the u-shaped backing plate. I have a spare one which you could have had. I decided not to fit it but go for the much later backing plate with the two loops for attaching break-away cables. It doesn't really show.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue May 19, 2020 9:22 pm

Fred wrote: ↑
Tue May 19, 2020 9:19 pm
I wish you'd said about the u-shaped backing plate. I have a spare one which you could have had. I decided not to fit it but go for the much later backing plate with the two loops for attaching break-away cables. It doesn't really show.
Ah well, that’s a kind thought buddy - maybe it can wait for the next 2a project we do together eh :D

I was thinking maybe winterised so at least we have some chance of staying warm in our old age.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu May 21, 2020 9:20 pm

A bit more today: I recovered the other rear bumperette and bolted to the chassis, plus drilled the missing hole for the drivers side rear lifting eye..

AF95C44D-5170-426B-89BB-7500294CCF1E.jpeg
AF95C44D-5170-426B-89BB-7500294CCF1E.jpeg (1.57 MiB) Viewed 1974 times

I also added another washer to each side of the bulkhead to pull it forward and therefore allow the seatbox and bulkhead to align with the front floors.

Might as well stick on one of the doors and check alignment. Well it’s poor but should adjust well at the hinges..

E249C095-4CDB-4322-97FA-5E11A04C2DAC.jpeg
E249C095-4CDB-4322-97FA-5E11A04C2DAC.jpeg (1.73 MiB) Viewed 1974 times

C0903FA9-3D24-4C13-B814-EC406F2BFE18.jpeg
C0903FA9-3D24-4C13-B814-EC406F2BFE18.jpeg (1.45 MiB) Viewed 1974 times

..speaking of hinges, I’m wondering who welded this up, and whether they are the same person who blagged the original top hinge pin using a bolt (long since replaced with a new item by yours truly)..

6743B93E-B3F5-412B-AE27-86D786077559.jpeg
6743B93E-B3F5-412B-AE27-86D786077559.jpeg (1.11 MiB) Viewed 1974 times

So now I’m on the hunt for the door half of the top drivers side hinge.


Work (work-work) has been crazy busy this week, so I’m having to fit this stuff in where I can, as well as my other project, a patio bar (because I miss being able to go to a real one). I want to get the landy into as close to ‘repaired but needs painting’ state as possible, because I think it would feel like a downhill job from there.

Let’s see eh,

All the best,

Andy

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Fri May 22, 2020 12:22 am

If I can't get my door top to fit, maybe I will break out the welder to adjust the door hinge...it wasn't something i had thought of previously but am running out of options! Oh and Andy, are you seriously using roofing bolts to hold your hinges on ??
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri May 22, 2020 6:47 am

landylees wrote: ↑
Fri May 22, 2020 12:22 am
If I can't get my door top to fit, maybe I will break out the welder to adjust the door hinge...it wasn't something i had thought of previously but am running out of options! Oh and Andy, are you seriously using roofing bolts to hold your hinges on ??

How bad is the door top issue?

They look like roofing bolts don’t they, they’re actually just machine screws with square nuts on the end. A temporary feature while I order some bits and pieces. The doors themselves both need skin-off repairs to the frames so it’s all coming apart shortly anyway.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri May 22, 2020 6:47 am

landylees wrote: ↑
Fri May 22, 2020 12:22 am
If I can't get my door top to fit, maybe I will break out the welder to adjust the door hinge...it wasn't something i had thought of previously but am running out of options! Oh and Andy, are you seriously using roofing bolts to hold your hinges on ??

How bad is the door top issue?

They look like roofing bolts don’t they, they’re actually just machine screws with square nuts on the end. A temporary feature while I order some bits and pieces. The doors themselves both need skin-off repairs to the frames so it’s all coming apart shortly anyway.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri May 22, 2020 7:06 pm

Not much time for play today as work was crazy busy. I did get a couple of bits in the post:

B8E58055-BB38-4717-BDCA-E8047027E3BB.jpeg
B8E58055-BB38-4717-BDCA-E8047027E3BB.jpeg (2.45 MiB) Viewed 1916 times

The belts were fitted, but only after loosening or removing most of the bolts holding on the dynamo, adjuster bracket and water pump.

The spacer for the NATO hitch was also duly stored away in place on the back of the truck - I’m sort of using it as it’s own filing system for now as I really, really need to sweep the garages out. There seems to be ten tonnes of metal shavings, dust and general grime left over from the bulkhead repairs back in October, and I need to sort the place out ahead of building a spray booth in there.

Beer time, have a good one!

Andy

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Sat May 23, 2020 11:14 am

andrewjsimpson1977 wrote: ↑
Fri May 22, 2020 6:47 am
landylees wrote: ↑
Fri May 22, 2020 12:22 am
If I can't get my door top to fit, maybe I will break out the welder to adjust the door hinge...it wasn't something i had thought of previously but am running out of options! Oh and Andy, are you seriously using roofing bolts to hold your hinges on ??

How bad is the door top issue?

They look like roofing bolts don’t they, they’re actually just machine screws with square nuts on the end. A temporary feature while I order some bits and pieces. The doors themselves both need skin-off repairs to the frames so it’s all coming apart shortly anyway.
I've been working on it, will post some pictures and questions on my own thread so as not to pollute yours!
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat May 23, 2020 5:22 pm

T’was a bit too windy today to be welding, so I thought I’d get stuck in to stripping down the nearside door.

It told a similar rotten story to its offside friend, needing a whole new bottom section to the frame (I have the stuff in stock) so that will get done tomorrow hopefully weather permitting.

E34F995F-9DD4-4CF3-BD0F-ACBACBB8C188.jpeg
E34F995F-9DD4-4CF3-BD0F-ACBACBB8C188.jpeg (2.14 MiB) Viewed 1642 times

The skin on this door is also toast. Crumbly, white, stale toast. I’ll be needing a new skin. I would usually at this point be thinking “I’ll just order some ally” but the pressed section around the handle aperture gives me the jitters. It’s doable, but no thanks.

I also stripped the windscreen down ahead of its little holiday to the galvanisers, whenever galvanising is deemed ‘essential’ enough for me to justify the trip.

ED22FE72-85CD-4C63-9335-77A72BEE3B2E.jpeg
ED22FE72-85CD-4C63-9335-77A72BEE3B2E.jpeg (1.09 MiB) Viewed 1652 times
4243AA31-FD93-4354-AE4E-EE4E4EECF5DD.jpeg
4243AA31-FD93-4354-AE4E-EE4E4EECF5DD.jpeg (1.2 MiB) Viewed 1652 times
DCE57B9F-643F-41C7-942E-CA09D8538C51.jpeg
DCE57B9F-643F-41C7-942E-CA09D8538C51.jpeg (1.73 MiB) Viewed 1652 times

I managed to keep all the little screws, which are in excellent condition, and the glass retaining bracketry which is also good and will clean up really well. The driver’s side pane is crack free, so while a new pair will be sourced, it’ll go into stores for a rainy day (or windy one?). Does anyone know of a good modern replacement for the sealant strips that make the glass water tight?

While it wasn’t what I had planned for today, It’s progress so I’ll take it.

All the best,

Andy
Last edited by andrewjsimpson1977 on Sat May 23, 2020 5:57 pm, edited 1 time in total.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat May 23, 2020 5:55 pm

Looks like SP make the skins so I’ll order when they reopen on Monday, as I should know by then whether I have viable frames or not.

And now, to the beer fridge!

Cheers.

Post Reply