What have you done there matey? Hope nothing too serious.AR4412 wrote: ↑Mon Jun 03, 2019 7:51 amHiya Andy!![]()
Good to see you had a productive day mate, it's coming together nicely.I had planned on doing some project work yeterday, but spent Saturday hobbling around, and all of yesterday laid up resting a bandaged ankle.
Have fun making brrmmm-brrmmm noises, I'm going to take some more industral strength pain killers and then we'll see if I can get a boot on over the bandage.
Look forwards to your next update, keep the flag flying.
Regards,
Monty the rather rusty 2A - 37FG31
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Re: Monty the rather rusty 2A - 37FG31
You know mate, I'm not entirely sure I did anything, it just started aching during the week and got worse.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Sorry to hear that Neil, I suppose at least it wasn’t a self inflicted wire brushing. I’ve (cough) heard those can be embarrassing
Re: Monty the rather rusty 2A - 37FG31
Rear tub is looking very good, I am very jealous...I should be in same position as you but still waiting for my fabricator to make seat back mark 2 (the one that fits hopefully)
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Hope it comes out better for you this time Howard - at the point I realised I had all the bits I needed to crack on it was a massive boost to morale.
A couple of bits from this evening’s tinkering..
First, the seat box piece I straightened yesterday - now cleaned of the last of the bitumastic and clamped up while the epoxy sets:
..and the cover plate from the front valance panel of the tub. Just a word on this, as someone in the landy’s past has taken an interesting approach to making a cable hole.. SO THATS HOW WE DO THAT IS IT?! WHAT DID YOU SMASH IT WITH A ROCK?!? USING A DRILL WAS JUST THAT BIT TOO TECHNICAL WAS IT?
Here it is after a blob of JBWeld (other brands are available) and a fair bit of sanding to get it flat:
I rescued and cleaned up the four original screws, so it can go on the vehicle tomorrow for safe keeping.
All the best,
Andy
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
On to the seat box then...
Having glued and (temporarily) riveted in the reinforcement to one of the wider support pieces, I cleaned the underseal off the other one with heat gun, scraper and then white spirit. Here they are together:
I put some initial etch primer on them, but more rubbing down and surface finishing is needed, so I'll update in a couple of days when they are presentable.
The smaller support pieces were looking a little tired - I don’t think this one for example is going to be riveted to anything anytime soon:
So, off to the old tub floor to rescue some top hat:
..and with the help of a large square block and a hammer I managed to ‘press’ a step into each end like the originals. Here the replacements are clamped in place:
I had thankfully cleaned the bitumastic off the main carcass of the seat box some time ago, which cuts a lot of work out of this job, as cleaning up the supports took long enough.
Having glued and (temporarily) riveted in the reinforcement to one of the wider support pieces, I cleaned the underseal off the other one with heat gun, scraper and then white spirit. Here they are together:
I put some initial etch primer on them, but more rubbing down and surface finishing is needed, so I'll update in a couple of days when they are presentable.
The smaller support pieces were looking a little tired - I don’t think this one for example is going to be riveted to anything anytime soon:
So, off to the old tub floor to rescue some top hat:
..and with the help of a large square block and a hammer I managed to ‘press’ a step into each end like the originals. Here the replacements are clamped in place:
I had thankfully cleaned the bitumastic off the main carcass of the seat box some time ago, which cuts a lot of work out of this job, as cleaning up the supports took long enough.
Last edited by andrewjsimpson1977 on Tue Jun 04, 2019 5:08 pm, edited 3 times in total.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Underside of the seat box, refreshingly un-bitumasticky:
..and the top side, but from a more jaunty angle:
Once the primer has gone off on the two wider supports, they will be offered up and and extraneous holes deleted. I do like this section of the project so far, as it’s a lot less grim and frustrating than other bits have been. And if that isn’t me jinxing myself, I’ll be a monkeys uncle.
Andy
..and the top side, but from a more jaunty angle:
Once the primer has gone off on the two wider supports, they will be offered up and and extraneous holes deleted. I do like this section of the project so far, as it’s a lot less grim and frustrating than other bits have been. And if that isn’t me jinxing myself, I’ll be a monkeys uncle.
Andy
Re: Monty the rather rusty 2A - 37FG31
Any chance of a photo of the “pressed” top hat(and maybe the block used?)? interested to see what you achieved since I bought new top hat and was going to cut and attempt to TIG weld the step
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
As it’s you Howard, let’s do an after-the-fact mockumentary
The finished top hat, if viewed from the side looks like this:
..and any old block of wood that’s big and hard enough will do. For the second one, I decided I’d give my back a rest and do it standing up
You have to hit the corner of the top hat where the horizontal piece meets the vertical, or you’ll just bend the ‘wings’ upwards. To induce a step you’ll have to wail on the corner edge to get it going. After I had done the two corners that fitted this way round on the end of the pallet, I flipped the panel round and did the other two corners (I hope that makes sense) on the other end of the pallet.
The results are pretty much the same as the original, but if you have an old floor and you want to save yourself half the effort, you could cut your repair pieces from the front ends of the floor top hats, which are already stepped to allow for fitting to the front valance panel. Sadly the front sections of mine were too damaged to take advantage of this.
Likelihood is, you'll need to run the hammer along the stepped, and unstepped bits afterwards, just levelling things out nicely and getting rid of any ripples, but its quite workable stuff. Also, ideally you should anneal the piece by heating it up with a blowtorch to finish, as you may have work-hardened the ally, and its going to be load-bearing so may be prone to cracking otherwise.
Hope this helps, but if it’s still unclear, ring me when you’re ready to do it and I’ll talk you through it.
All the best,
Andy
Re: Monty the rather rusty 2A - 37FG31
Check out the fabricating skills on Andy. Nicely done there mate.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.