Buying a Sankey

Any trailer related disscussion
Post Reply
Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Buying a Sankey

Post by Landie68 » Thu Feb 14, 2019 9:46 pm

I am off to look at a Sankey to purchase. Knowing the in depth knowledge that this forum has, what should I be looking out for? It is a NT, age not known.

Any advice would be very much appreciated.
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Buying a Sankey

Post by removeduser185 » Thu Feb 14, 2019 10:32 pm

Well, judging by recent adverts, make sure the tub is on the right way round for a start! :roll:

User avatar
Sidders101
Bake Off Judge
Posts: 2406
Joined: Wed Apr 02, 2014 7:57 pm
Location: Winchester

Re: Buying a Sankey

Post by Sidders101 » Fri Feb 15, 2019 8:47 am

check the tub..i mean really check the tub.. a small amount of corner corrosion is acceptable and not too much hassle to repair...the front lower edge is usually the problem area as this holds the water when the trailer is left outside tipped forward.Alot of trailers have had this repaired by a sheet of steel, tack welded over the damage...bring a magnet.
check underneath the toe "A" frame box right at the front..this is also a water trap so tap with a small hammer for the distinctive sound of tin worm.
Chassis are quite well constructed but check where the J bolts hold the tub on. Plug in the electrics and check all the lights.Pull the handbrake on and turn trailer from left to right to check individual brake system linkage.There are various draw bar set ups on these trailers, some have hydraulic dampers some just have a spring damper...the seals can go and fluid escapes..these are difficult to disassemble to replace seals..the front leg is almost always bent and you will not be able to straighten it although replacements can still be bought NOS. .If these trailers are corroded they are a swine to repair...always best to bide your time and wait for the right trailer.Ive bought NT's for £350 and they have been expensive & time consuming to put right & ive bought them for £250 and not had to do anything...it really is not financially viable to buy one that needs work so prepare to spend £500 plus.
Take lots of pics & report back here as loads of members have repaired/restored these trailers and know all the pitfalls. Good Luck.
Sidders


1974 Series 3 LWT 12v RHD 69-FM-24 , Royal Marines ("Intrepid")
1976 101 forward control gun tractor 12v RHD- 73-FL-43 ex 1,2 & 3 Para ("Kryten")
1979 Sankey NT Trailer 06-HF-86 78 Engr Reg (Herman)
1978 Trophy Frank Spencer impression (1st place)

User avatar
Trickyh
Posts: 293
Joined: Mon Aug 21, 2017 1:17 pm
Location: Reading, Berks

Re: Buying a Sankey

Post by Trickyh » Fri Feb 15, 2019 10:30 am

Agree 100% with what Sid says

Plus check state of tyres, even replacing a pair with decent tread is starting to get expensive..
Rich aka Tricky

'72 SIII 12V GS Lightweight
Sankey

Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Re: Buying a Sankey

Post by Landie68 » Fri Feb 15, 2019 8:35 pm

Thanks guys, especially Sidders for the areas I need to double check out. Apparently it is plywood lined, so I am expecting that to be covering a multitude of sins.
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

User avatar
Sidders101
Bake Off Judge
Posts: 2406
Joined: Wed Apr 02, 2014 7:57 pm
Location: Winchester

Re: Buying a Sankey

Post by Sidders101 » Sat Feb 16, 2019 8:04 am

And the vertical corner seams..if they show signs of corrosion on the outer edge then the inner corners will be worse.corners of the wheel arches are very prone..also the 1 1/2 seam plate that surrounds the floor is a water trap...it goes on and on..As Tricky says the correct hi miler tyres are getting hard to find and make sure the rims are not LWB/750-16 otherwise it will severely tow nose down.all the NT's on ebay currently look toast.Usually there are a few at newbury..get a square number plate made up with adhesive backing strips so if u do buy one you can get it home. Rodders...anything else...?
Sidders


1974 Series 3 LWT 12v RHD 69-FM-24 , Royal Marines ("Intrepid")
1976 101 forward control gun tractor 12v RHD- 73-FL-43 ex 1,2 & 3 Para ("Kryten")
1979 Sankey NT Trailer 06-HF-86 78 Engr Reg (Herman)
1978 Trophy Frank Spencer impression (1st place)

User avatar
the landy man
Cake Guru
Posts: 3080
Joined: Wed Sep 28, 2011 1:00 pm
Location: BOGNOR REGIS

Re: Buying a Sankey

Post by the landy man » Sat Feb 16, 2019 11:00 am

Sidders101 wrote: ↑
Sat Feb 16, 2019 8:04 am
And the vertical corner seams..if they show signs of corrosion on the outer edge then the inner corners will be worse.corners of the wheel arches are very prone..also the 1 1/2 seam plate that surrounds the floor is a water trap...it goes on and on..As Tricky says the correct hi miler tyres are getting hard to find and make sure the rims are not LWB/750-16 otherwise it will severely tow nose down.all the NT's on ebay currently look toast.Usually there are a few at newbury..get a square number plate made up with adhesive backing strips so if u do buy one you can get it home. Rodders...anything else...?
I think you've covered it all Sidders!
I must get round to Looking at my 'Mankey Sankey' this year!!
..ROD..
Bognor Regis,West Sussex


1972 S3 LIGHTWEIGHT 53 AM 74,RAF GS .Waddington strike command
1979 LIGHTWEIGHT 10 GX 11,GS .Black watch 1st battalion
1964 SERIES 2A..
Sankey narrow track,29 EN 84
Sankey narrow track project.
1967 BSA b40 WD 350cc.
1957 Triumph 6T Thunderbird.

Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Re: Buying a Sankey

Post by Landie68 » Thu Feb 21, 2019 12:00 pm

Thanks guys for all the advice. I did purchase it, just need to get it home now. A PO decided that it might be a good idea to cut the back out and create a tailgate for it. This doesn't particularly bother me, as it means with my bad back I don't have to go leaning over the sides to get at things. Definitely not one for the purests but the price said it was right for me.

I will post some pictures once I get it home. Tyres appear ok, but the rims look wrong, so I shall be on the hunt for another set of rims at Newbury, along with correct light fittings and the NATO light plug (yep, you guessed it, it has been converted to a standard 7 pin plug :evil: )
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

Jiml
Pastry Chef
Posts: 644
Joined: Sat Jul 18, 2015 1:56 pm
Location: Burnley Lancashire
Contact:

Re: Buying a Sankey

Post by Jiml » Thu Feb 21, 2019 2:43 pm

Get it home, where is it coming from Richard?
52HG42 my current love interest

Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Re: Buying a Sankey

Post by Landie68 » Thu Feb 21, 2019 7:33 pm

Jiml wrote: ↑
Thu Feb 21, 2019 2:43 pm
Get it home, where is it coming from Richard?
Stoke on Trent Jim.
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

Post Reply