Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Mon Jun 19, 2017 9:39 pm

Finally someone with standards!

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jun 20, 2017 10:44 pm

Had a first attempt this evening at ally welding with the MIG. I'm still a rank amateur at welding overall, and aluminium is notoriously difficult, especially if you don't have a TIG, or your name isn't Neil. Hi Neil :D

First job was to mark off all the areas needing work. I have marked anything from holes to pitting and cracks, as it might as well all be fixed while I'm at it.
IMG_4499.JPG
IMG_4499.JPG (107.96 KiB) Viewed 1613 times
You can see here the worst section, where one of the steel cross-supports had caused the ally floor strengthener to corrode away completely
IMG_4501.JPG
IMG_4501.JPG (43.12 KiB) Viewed 1613 times
I started on these holes in the under-floor reinforcement, and quickly realised that the approach I was most comfortable with was to simply fill up the void behind the hole in the aluminium. I prefered this rather than cutting fiddly pieces of aluminium repair patches out which (by the nature of aluminium) cannot be held in place with my welding magnets.

It took about half an hour of trial and error to realise that the best setting on the MIG for this allocation was one up from the lowest. Anything less and the aluminium just turned to pigeon s*#t. Anything higher, and I was blowing holes through the bit next to the bit I was welding up. Grr.

Once I had the right setting (setting 2 of 2, with the min/max switch set to 'min'), I began filling the holes up. It's ugly, and will need a fair bit of shaping with the flap wheel grinder attachment, but I'm really pleased that the holes are dissapearing.

Here you can see I have mostly filled that biggest void:
IMG_4496.JPG
IMG_4496.JPG (117.44 KiB) Viewed 1613 times
..and here you can see a typical weld (for me). I think it's a bit too blobby because the wind was gusting and blowing the shielding gas away.
IMG_4497.JPG
IMG_4497.JPG (113.15 KiB) Viewed 1613 times
For the next session I'll move into the garage and see if that makes a difference.

I've also got a brass block on order for the hole on the edge, as I'll need something to help form the shape of the edge and stop all the molten aluminium dropping out. I should have mentioned as well that as it's aluminium being welded, I have swapped the gas out for pure argon.

You'll have to forgive me if the next few updates are even slower paced than usual.. I'm learning as I go, and there is lot to get through before the whole tub is repaired.

All the best,

Andy

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Tue Jun 20, 2017 11:29 pm

Well, I'm suitably impressed! I think you are more courageous than I was. My floor was less damaged and I opted to replace it altogether. And that was despite following every stage of Neil's restoration open-mouthed. I wish that, at the outset, I had had the courage to address my inability to weld. I could have got help from my neighbour, who is excellent - even my wife, who, in her dim and distant past (oi! not that distant past! - ed) could weld. But, I didn't. Anyway, keep at it, it may look scruffy now, but, as you say, once you have been over it with a flap wheel, I am sure it will be fine - and, if it isn't you can have my old floor!

Best

Fred

Gordon Bennett
Maître Pâtissier
Posts: 7422
Joined: Sun Jan 10, 2010 12:21 pm

Re: Monty the rather rusty 2A - 37FG31

Post by Gordon Bennett » Tue Jun 20, 2017 11:32 pm

Hi Andy,

Great effort. Practice makes perfect. You're doing really well :P

Rgds,
Gordon

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Tue Jun 20, 2017 11:40 pm

Thanks Ian - you should have told your good lady to get her welding goggles on and earn her keep! Please don't tell her I said that. In fact, say Gordon said it. Hi Gordon :lol:

Welding, I have come to realise, is all about squirting in / on more liquified metal than you need, and then hiding the mess by shaping it to what I wish could be achieved with the torch alone.

The best bit about the sections of reinforcement which need building up, is that they are all going to be covered by the steel cross supports eventually, so if the end results are less than aesthetically perfect (but structurally sound) I won't lose too much sleep.

Later in the week hopefully I'll get some more time to finish filling the holes so I can move on to prettying it all up.

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Jun 21, 2017 7:03 pm

Ok it's a bit of a lame update, but in-keeping with my recent commitment to do something towards the project every day.. I present: rear axle brake junction
IMG_4506.JPG
IMG_4506.JPG (79.2 KiB) Viewed 1632 times
It's been dipped in vinegar for a week, and after some persuasion the old screw in connector ends of the brake pipes and flexi hose came out.

A spot of brasso later, and it was ready to bolt back on.

I'll admit I'm looking for the easy jobs at the moment. Something to do with the sun being out and beer still being available. :!

Andy

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Wed Jun 21, 2017 7:57 pm

Hiya Andy! :D

Nice to see you're tackling the ali welding yourself mate. 8-) It's a frustrating exercise with a MIG welder, but can be done. Good luck with the repairs to the floor mate, and remember, you can hide many a sin with a flap disc and a belt sander. :D

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Jun 21, 2017 8:06 pm

I think a belt sander might be on the shopping list Neil - as i found the grinder / flap wheel approach ate too much of the aluminium too quickly.

You're right about it being a frustrating process - but I'm getting there slowly. Can I ask - did you find you had to turn the wire speed right up in order to get a decent weld puddle? Its not like welding steel thats for sure!

Andy

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Wed Jun 21, 2017 8:17 pm

I did turn the wire speed up, as much as to stop it sticking to the tip as anything. I also welded in shorter bursts to keep the heat expansion in the wire down to stop it sticking and creating a birds nest.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri Jun 23, 2017 5:04 pm

A couple of little bits done.

Yesterday I took the four way brake pipe union and bracket off the old chassis. Not interesting enough for a photo until they are cleaned up and refitted, but its another vItal stage to get sorted before the new brake pipes arrive.

Today I took one of the outer swivel housings out of the degreaser bucket, cleaned it up with a wire wheel, and got it into anti rust primer.
IMG_4521.JPG
IMG_4521.JPG (106.75 KiB) Viewed 1590 times
It's now had a coat of grey and I'll try to get some top coat on over the weekend.
IMG_4522.JPG
IMG_4522.JPG (118.7 KiB) Viewed 1590 times
IMG_4524.JPG
IMG_4524.JPG (107.68 KiB) Viewed 1590 times
The other outer housing is as still technically part of the hub, as up til now I hadn't been able to get the brake drum off. Two of the screws had completely corroded into the drum, and wouldn't accept being drifted around and out like the others have. I drilled the heads off in the end, so I'll need to carefully remove the stumps from the hub at some point. The drum survived the experience unscathed thankfully - and is now back in the de rusting dip. The hub is also in pickling away nicely, which just leaves the stub axle to remove from the swivel casing in the morning.

I'm hoping to get the second casing in paint tomorrow too, as it would be nice to have the pair done, so I can get back to repairing the tub. Let's see how the weekend unfolds, as I'm always making grand commitments only to get half the way through, tired, frustrated and covered in gunge.

That's it from me for today - it is a wine and Chinese themed evening in Simpson Hall this evening (I know, that classic combo), so it's time to put the spanners away.

See you guys tomorrow,

Andy

Post Reply