Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Jun 10, 2017 6:43 pm

I know what you mean Adam - the thing is if I don't fit it now it'll go walkies :lol:

Will loosely bolt it up hand tight, and remove when it's time to fit the seat box - as I can see it being a pain in the rear to get the box over otherwise.

Right.. today's update:

We decided to take the kids to Silverstone today as it's the British GT and F3 weekend. Had fun for a few hours and then home in time to prep for tomorrow afternoon's work.

After rescuing the dried up gunk tank full of the salt that used to be acid - adding some water and a quick stir turned it back to super strong acid solution in no time.

Into the acid has gone:

1) wheel rim
2) both bulkhead brackets
3) handbrake mechanism (I removed the lower bracket swivel fixing it from the old chassis to go in with the rest of the handbrake lever)
4) 2 x rear brake drums
5) a whole or host of pins, bolts, hub end caps, drive members, nuts and bracketry

In addition the steering box went into white spirit

There are no photos - I'm sure you lot probably draw the line at pictures of grey gunk with metal stuff poking out of it.

How fully tomorrow I can turn some of this stuff into shiny-shiny.

Oh and PS: my dead grinder came back to life!! Hooray!

Have a great evening,

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jun 11, 2017 8:50 pm

A selection of photos from today. I didn't get started til late as we were back in Stratford (meeting my in laws this time). A lovely afternoon and a good lunch - but once back home I set to work.

I'll try to keep it brief because it's tea time and my hands are tired as I type this.

Finished stripping another wheel - and into anti rust primer:
IMG_4171.JPG
IMG_4171.JPG (141.5 KiB) Viewed 1209 times
Finished cleaning up the handbrake lever, and also into primer:
IMG_4172.JPG
IMG_4172.JPG (168.61 KiB) Viewed 1209 times
Retrieved the rear drums from the acid dip - not much seemed to have happened (I think the acid has finally been neutralised by all the paint and gunk it has stripped off).
Was pleasantly surprised by how well the drums cleaned up with the wire brush / grinder ensemble. Once they were clean I added anti rust primer, which I where they are up to so far.
IMG_4170.JPG
IMG_4170.JPG (133.73 KiB) Viewed 1209 times
I also manhandled the tub outside and was unpleasantly surprised at how much bitumastic was left stuck on the underside. An hour with the grinder and half an hour with scouring pads and white spirit and I have cut the problem in half. Need to get more white spirit but the job feels a bit closer to the end now.
IMG_4173.JPG
IMG_4173.JPG (111.19 KiB) Viewed 1209 times
Will try to get some black on the drums if there is time in an hour or so, but apart from that - I'm all done for the day.

Now where did I put that Battenberg..

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jun 11, 2017 9:05 pm

Drums in grey primer. I thought they would benefit from an extra coat of protection.
IMG_4178.JPG
IMG_4178.JPG (104.74 KiB) Viewed 1205 times
Think I should still have time (just) to get some black on shortly..

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jun 11, 2017 9:59 pm

.. right that's really it now. More in the week with any luck..
IMG_4192.JPG
IMG_4192.JPG (120.44 KiB) Viewed 1200 times
All the best,

Andy
Attachments
IMG_4193.JPG
IMG_4193.JPG (110.06 KiB) Viewed 1200 times

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sun Jun 11, 2017 10:15 pm

I found a hot air gun and a scraper to be the most effective and least messy way of getting the bitumen underseal off. Once all the thick stuff was off, a rub over with kero lifted the remainder and the paint was left underneath.
These wings were thick with it, but it all came off easily enough. It is also quite satisfying in an odd sort of way!
underneath offside front wing.JPG
underneath offside front wing.JPG (1.12 MiB) Viewed 1194 times
I notice that you have three holes for securing each brake drum to the hub, so you'll need the extra screws. Mine had only one hole per drum - another change from Series 2A to 3?

I got nothing done today. I was persuaded to go to see a local garden which was open under the National Garden Scheme. Got there to find that the owner was a Land Rover aficionado - he had a beautiful, early 2-door Range Rover undergoing a ground-up restoration- in sage green - just perfect. And, in a barn nearby an unmolested Series 3 awaiting its turn! So all was not lost!

Fred

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Sun Jun 11, 2017 10:23 pm

andrewjsimpson1977 wrote: ↑
Sun Jun 11, 2017 8:50 pm
Now where did I put that Battenberg..
Hopefully straight into the bin.


Good to see you've got some more done around family commitments mate, and good to see no reports of trying to remove your t-shirt with an angle grinder today.

I think my acid dip has reached the same stage as yours as it didn't work as well on the front springs as it did on the rears.

I used the same method as Fred to remove the underseal from the Recce.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sun Jun 11, 2017 10:27 pm

AR4412 wrote: ↑
Sun Jun 11, 2017 10:23 pm


I used the same method as Fred to remove the underseal from the Recce.

Regards,
No, I think you'll find I used the same method as you!

Fred

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jun 11, 2017 10:30 pm

Nice when the day is saved eh Fred? I often comment on landys we pass while out with the kids, but Mrs S usually just sighs and we drive on in silence.

I think the drums must have been replacement ones at some point. There was certainly only one screw per side holding them on. Without going out to the garage again, I can't remember whether the hubs have more than one hole for the screws. Either way, I have enough screws for all eventualities.

Thanks for the tip on using kero - I have a 1200 litre tank of the stuff as it heats my home, so I'm sure I could spare a little for the project. I use white spirit at the moment, but it can be a little slow to dissolve the underseal.

Neil - yes you'll be relived to hear there was no repeat of my 'chunky chippendale' moment, although I did come back in the house covered from head to foot in tiny blobs of bitumastic. Sara shot me a look that can only have meant "out, now", so I was relegated to the yard while I did my best to white spirit myself clean.

I have a feeling I am still not welcome back in, but it's cold and getting dark out there.. and one of the neighbourhood cats is REALLY scary :shock:

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Mon Jun 12, 2017 6:30 pm

A couple of jobs tonight... hub end caps re-re-resprayed (kept stuffing up the paint job for some reason), second coat on the rear drums and on to the axle.
IMG_4197.JPG
IMG_4197.JPG (94.38 KiB) Viewed 1299 times
IMG_4198.JPG
IMG_4198.JPG (106.93 KiB) Viewed 1299 times
Still no seals or drive member gaskets fitted - I'll do that once I can wheel the thing out in the open, as if the diff ends up needing any adjustment it'll mean half shafts will have to come out, and I'd rather do that job in the sunshine with a beer in hand. A rare example of me trying to think ahead.

It's nice to see the drums on - the thought that I could pop the old wheels and tyres back on and wheel it out into the yard is quite satisfying. I really must hurry up and get on with the front axle..

Andy

Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Re: Monty the rather rusty 2A - 37FG31

Post by Landie68 » Wed Jun 14, 2017 6:50 pm

Looking good, hopefully I can catch up soon, but guess I will always be at least an axle behind.
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

Post Reply