Monty the rather rusty 2A - 37FG31
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Just a quick update on the other rear hub. This is the one that was repaired as the mating face was damaged.
A quick rub down of the mating face to get rid of the paint over spray, and a thorough clean to remove be any swarf and residual dirt and we are good to go..
Outer race in:
Inner race in:
I also greased and fitted the inner bearing and oil seal, but have stopped there as I need to swap the brake plates over before fitting the hubs to the stub axles. That's a job for the weekend - but for now I'm pleased there is one more job ticked off the list.
Andy
A quick rub down of the mating face to get rid of the paint over spray, and a thorough clean to remove be any swarf and residual dirt and we are good to go..
Outer race in:
Inner race in:
I also greased and fitted the inner bearing and oil seal, but have stopped there as I need to swap the brake plates over before fitting the hubs to the stub axles. That's a job for the weekend - but for now I'm pleased there is one more job ticked off the list.
Andy
Re: Monty the rather rusty 2A - 37FG31
Nice job on the hub Andy.
I would have put some plasticine in the pits. If you saw my welding you would agree!
Now know mine are/were held on with 3/8 BSF nuts and bolts which is marvellous as I have enough bolts but only 3 nuts.
Back to propshafts then.
Mac
I would have put some plasticine in the pits. If you saw my welding you would agree!
Now know mine are/were held on with 3/8 BSF nuts and bolts which is marvellous as I have enough bolts but only 3 nuts.
Back to propshafts then.
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Thanks Mac - repairing the hub face is easy - even if your welding looks like pigeon poo. Its just a matter of blobbing on weld onto the divots in the face, and then grinding it all flat with a spinny sanding pad on a drill. A quick flat off on a level surface with sandpaper on it, and its all done.
Re the fasteners - I got a pack of new nuts and bolts - enough to do a whole axle - for 15 quid
http://www.ebay.co.uk/itm/221758406053? ... EBIDX%3AIT
I have also discovered that i can now only find two of the bolts that go through the end cap / drive member into the hub. Suspect the other four are in my acid dip so will have to go fishing later in the week.
Sometimes I wish i was more organised. You wouldn't think I'm a project manager and requirements guy by trade.
PS - its the same nuts and bolts for the prop shafts, so if you don't have them, you can't fit the prop shafts either.
Sorry
Andy
Re the fasteners - I got a pack of new nuts and bolts - enough to do a whole axle - for 15 quid
http://www.ebay.co.uk/itm/221758406053? ... EBIDX%3AIT
I have also discovered that i can now only find two of the bolts that go through the end cap / drive member into the hub. Suspect the other four are in my acid dip so will have to go fishing later in the week.
Sometimes I wish i was more organised. You wouldn't think I'm a project manager and requirements guy by trade.
PS - its the same nuts and bolts for the prop shafts, so if you don't have them, you can't fit the prop shafts either.
Sorry
Andy
Re: Monty the rather rusty 2A - 37FG31
Thanks Andy, I will check out the nuts bolts link.
See what you mean on the inner oil seal. Yours defo further in than mine which is flush. Hopefully it makes little difference!
Organised? You? Certainly appears so.
Propshafts-thanks for the bolt info. No gearbox either as still in the wood 5 miles up the valley!
Mac
See what you mean on the inner oil seal. Yours defo further in than mine which is flush. Hopefully it makes little difference!
Organised? You? Certainly appears so.
Propshafts-thanks for the bolt info. No gearbox either as still in the wood 5 miles up the valley!
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
That doesn't sound the safest storage place to be honest mate. Where in the country are you based? Are you waiting for help to collect it?
Re: Monty the rather rusty 2A - 37FG31
Agreed Andy it's not ideal but that iis how it rolls with the unexpected. No probs picking up, just nowhere better to put it until I get a chassis. Thank you very much for asking. I am south of Tunbridge Wells if you ever are down this way... no sprouts or battenburg!
Bad luck on the end cap bolts. Sadly can't be helpful and say which others might fit, if any.
Mac
Bad luck on the end cap bolts. Sadly can't be helpful and say which others might fit, if any.
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
-
Gordon Bennett
- Maître Pâtissier
- Posts: 7422
- Joined: Sun Jan 10, 2010 12:21 pm
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Count me out. I have a very strict cake-based belief system which precludes visiting infidels
Re: Monty the rather rusty 2A - 37FG31
What's "preclude" mean!
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Another frustrating day - I managed to strip the other rear spring and get it into acid, and the brake plates and hubs were swapped over following last weekend's bungling efforts. Play was stopped by a pickup of daughter and friends from a kids party, that ended up eating an hour and a half. I came back to find the axle being rained on, so I dried everything out as best I could, nipped up the last few bolts and wheeled the damned thing inside for the night.
I really wanted to get the springs coated and rebuilt this weekend, but events conspired against me. I did try at one point to speed up the de-rusting with my new grinder - but it died almost immediately. Literally caught fire in my hands. Moral of the story is, don't buy cheap grinders.
Tomorrow we are visiting family in staffs, so no play unfortunately.
Harrumph.
If it helps with the photo drought, see below the lovely condition the first leaf spring pieces were in when they came out of the acid. I'm really happy with this - just need the time now to get the bits coated and rebuilt back into spring packs.
All the best,
Andy
I really wanted to get the springs coated and rebuilt this weekend, but events conspired against me. I did try at one point to speed up the de-rusting with my new grinder - but it died almost immediately. Literally caught fire in my hands. Moral of the story is, don't buy cheap grinders.
Tomorrow we are visiting family in staffs, so no play unfortunately.
Harrumph.
If it helps with the photo drought, see below the lovely condition the first leaf spring pieces were in when they came out of the acid. I'm really happy with this - just need the time now to get the bits coated and rebuilt back into spring packs.
All the best,
Andy