FM, What have I done project

Tell us about any of your Land Rover related projects here.
greyleaf
Posts: 208
Joined: Fri Jul 15, 2016 8:54 pm
Location: Warrington

Re: FM, What have I done project

Post by greyleaf » Sun Oct 23, 2016 7:22 pm

Thanks Neil, sorry i am not being very specific with my problems.
I cannot work out how to remove the wires to allow me to remove the flasher unit.
The hella flasher has two small lugs opposite each other, with a small screwdriver push in one lug and ease it up out of its hole now do the same on the other side being careful not to push the one you've done back in its hole. This separates the button from the wires, the wires are spade terminals and clip in like normal ones.
Thanks
Graham

1974 LWT 24v FFR 33GB11

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Nov 27, 2016 7:12 am

Rear Suspension was solid. Now Rea leased. Sadly, one leaf gave up.
Attachments
IMG_3563.JPG
IMG_3563.JPG (772.5 KiB) Viewed 1855 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Nov 27, 2016 7:23 am

Realeased.
Will have do to start with..
Don't really want to cut the clips but guess that is only way to do a more thorough job?
Attachments
IMG_3567.JPG
IMG_3567.JPG (692 KiB) Viewed 1855 times
IMG_3566.JPG
IMG_3566.JPG (662.53 KiB) Viewed 1855 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

User avatar
StuWright
Master Baker
Posts: 1740
Joined: Wed Feb 24, 2016 11:10 pm
Location: Southampton

Re: FM, What have I done project

Post by StuWright » Sun Nov 27, 2016 5:42 pm

Well worth getting them apart to clean them thoroughly. Good pictures and I'm interested to see them separated and cleaned. How will you clean them?

I used a commercial de-rusting solution in a spray bottle. Everyday I sprayed a bit on and gave the clip a bit of hammer love. Eventually I got them apart in good order. Granted this was a truck but same principle.
Thanks

Stu

55AM52 Ex RAF Land Rover Lightweight GS

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Nov 27, 2016 6:34 pm

Hi Stu,
Was thinking of leaving them to soak in white vinegar for a week. 5lts £3.00. What commercial de ruster do you use?
Did you just ease apart the clips after heating or cut and weld them?
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: FM, What have I done project

Post by removeduser185 » Sun Nov 27, 2016 10:37 pm

Macvfork wrote:Hi Stu,
Was thinking of leaving them to soak in white vinegar for a week. 5lts £3.00. What commercial de ruster do you use?
Did you just ease apart the clips after heating or cut and weld them?
Mac
I'm a believer in vinegar as well - I use cider vinegar (last time it was organic - on special offer!!) and, although it isn't quite as good as vaporust, it is a lot cheaper and good enough. To do the four strengthening ribs under the tub I made up a trough out of a length of plastic guttering and left each one in there covered in the vinegar for a few days - garage smelt great and the ribs came up a treat.

Fred

User avatar
Davidmg
Posts: 303
Joined: Sun Jul 28, 2013 11:07 am
Location: Nottingham

Re: FM, What have I done project

Post by Davidmg » Sun Nov 27, 2016 10:41 pm

Perhaps give phosphoric acid a try. It can be bought quite cheaply on ebay in 25lts 45% and watered down, so goes a long way

User avatar
StuWright
Master Baker
Posts: 1740
Joined: Wed Feb 24, 2016 11:10 pm
Location: Southampton

Re: FM, What have I done project

Post by StuWright » Tue Nov 29, 2016 12:12 am

Macvfork wrote:Hi Stu,
Was thinking of leaving them to soak in white vinegar for a week. 5lts £3.00. What commercial de ruster do you use?
Did you just ease apart the clips after heating or cut and weld them?
Mac
Not sure what it was but like vaporust. I have heard people using vinegar before and even coke cola. Luckily I didn't need to use heat to get the clips off and they became loose once the rust started breaking down. I used a flat bit of metal so I could put it against it to hit with a hammer. It just helped the loosening process without hitting the clips directly and damaging them.
Not tried cutting and welding but I'm not a welder unfortunately.

I'm interested to see the results as I'm going to be doing that to my trailer in the Spring.
Thanks

Stu

55AM52 Ex RAF Land Rover Lightweight GS

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Fri Dec 02, 2016 6:56 pm

As requested one set now apart. Knowing what I do now I think I might try grinding the rivet head off rather than bending the clips as I reckon that would be best., having first found some suitable rivets. First port of call will be the combine spares box as loads used for the cutter bar. Anyone know if the rivets are available off the shelf?

After sanding to remove lumps but not pitting I will probably splash on some rust killer ( getting better at that) followed by satin black cio paint. Followed by graphite powder before reassembly. Views appreciated.

Anyone know the part numbers for the rubber bits, sleeve and bolts etc that go through the last leaf?

Mac
Attachments
IMG_3585.JPG
IMG_3585.JPG (849.88 KiB) Viewed 1742 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

User avatar
StuWright
Master Baker
Posts: 1740
Joined: Wed Feb 24, 2016 11:10 pm
Location: Southampton

Re: FM, What have I done project

Post by StuWright » Fri Dec 02, 2016 7:14 pm

Have you got anyone who could carefully shot blast them off for you, which would be a good start?

Lots of different options for coating Mac. I know some people who rust treat the metal and then just oil it before assembly. I have see this done with the addition of spray painting what is exposed after and also the totally sprayed option. I am sure some of the guys will give their views. In the Army we never painted them and just oiled them if they were getting sticky.
After stripping to bare metal, leaving for a few days in a hot room, I painted mine with Eastwood rust encapsulation. It has rust killer properties and semi flexible. Maybe easier on my springs though because they are parabolic and have the slight gap to stop the leaves rubbing together.

Nice work getting them apart though. ;)
Thanks

Stu

55AM52 Ex RAF Land Rover Lightweight GS

Post Reply