Rebuild of 05 HH 50 GS SIII

Tell us about any of your Land Rover related projects here.
Gordon Bennett
Maître Pâtissier
Posts: 7422
Joined: Sun Jan 10, 2010 12:21 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by Gordon Bennett » Sun Oct 20, 2013 8:23 pm

Great progress 8-)

Rgds,
Gordon

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Mon Oct 21, 2013 8:18 am

Neil,

Thanks for the advice and the link (951 prefix were built for lightweights so that's encouraging).

Good luck with your tub repairs.

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Rebuild of 05 HH 50 GS SIII

Post by AR4412 » Mon Oct 21, 2013 10:14 am

Thanks, repairing the tub should keep me occupied for a bit. Looks like your gearbox probably recieved an upgrade to 'B' specification hence the overstamping.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Sun Oct 27, 2013 5:25 pm

The strip down continues, in this picture I've removed the front panel. I have left the oil cooler in place for the time being. The frame of the front panel is fine but the front plates are shot, so I've bought 2x replacements from bits 4 landys (slightly cheaper if you buy direct rather than eBay)
LR14.jpg
LR14.jpg (150.47 KiB) Viewed 2577 times
Thought I might get away with just a new cross member, but have decided to go for a new 1/4 chassis and get rid of these patches at the same time.
LR15.jpg
LR15.jpg (172.85 KiB) Viewed 2577 times
I've also taken the fuel tanks off, need to test one of them for leaks. Looks like one or both were replaced by a PO so I'm hoping I can just clean them up and repaint them.
LR16.jpg
LR16.jpg (162.36 KiB) Viewed 2577 times
I've also taken the rear exhaust off, and the axle check straps to get better access to the axle bumpstops. Neil you were right, there's a small hole on one side of the chassis leg which will need to be repaired. Still need to remove the ones on the front axle, but they seem to sit off the chassis leg (different design?) so fingers crossed they wont be as bad. Also broke out the hot air gun to start removing the bitumen off the chassis....what a job that is. Surprised how fresh the chassis paint is in some places. Looks like I'm also going to have to replace one of the bulkhead outriggers, and possibly one of the fuel tank outriggers which has been poorly repaired.

Tried to remove the door hinges, and managed 1 out of 4. :( Good news is having removed the aluminium cover plates from the A post on the bulkhead to access the hinge bolts, I was pleasantly surprised at the condition of the bulkhead so hopefully will get away with replacing the footwells and the hinge panels (which arrived this week...thanks Les).

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Rebuild of 05 HH 50 GS SIII

Post by AR4412 » Sun Oct 27, 2013 8:23 pm

Good progress there mate. I hope that your fuel tank turns out to be okay. Both mine are shot but luckily I had a pair stored that are leak free, just need to give the insides a dose of POR15 treatment to deal with some surface rusting and a clean and paint on the outside.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Sat Nov 02, 2013 5:31 pm

Sorry no pics...too bloody dark :cry:
Busy day but not a lot to show for it, started by stripping down the tub. Half the bolts securing the cleats sheared so captive nuts will need to be drilled and re-tapped. Galvanised strips on the load bed were next, I have left the cappings on for the time being to protect the tub. Then onto the bonnet...no drama's here, spare wheel brackets, washer jets, hinges, bonnet stay all came off with no bother.

Need to order up the bits for the chassis repairs...have done some internet research and I'm going to try gdiproducts, they advertise on eBay and claim the parts are made in the UK using identical materials to the OEM...I'll let you know what the quality is like. Talking of eBay have you seen this...
http://www.ebay.co.uk/itm/LAND-ROVER-LI ... 4acb3e652d

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Rebuild of 05 HH 50 GS SIII

Post by AR4412 » Sat Nov 02, 2013 7:58 pm

Hi Shaun,

Looks like you've had the same problem as me with the lashing cleat bolts shearing in the captive nuts. I've got four of the plates out of mine, the rear two are held captive by the tub's body panels so I haven't got them out yet. I've yet to try to get the sheared bolts out, need to give them a soak first. If I can't get them out I'll probably make new ones. I haven't searched the parts list to find the part numbers and see if there's any out there yet though.

I had a look at the gdiproduct bits, I quite like the look of their spring hanger mountings, it gives me another repair option for the chassis on mine as it has holes around them. I was thinking of trying to remove them from my chassis, carrying out a plate repair and welding them back on as opposed to renewing everything with a new cross member with extensions. If I can carry out some plate repairs and fit the gdi spring hangers I may get away with just renewing the rear cross member itself. I will decide once I've blasted the chassis clean and had a good look at what is required. Thanks for the tip off as I didn't know those bits were available seperately. 8-)

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Sun Nov 10, 2013 4:53 pm

Not much to show for this weekends efforts...but tackled some stubborn jobs I've been putting off. Bought some new drill bits to drill out the heads of the hinge bolts, managed to get them all off and only snapped 2x drill bits. :)
Main effort this weekend was focused on stripping down the tub, after a good soaking of penetrating oil I managed to get the seat belt brackets off without shearing any bolts. As you can see from the picture they've done a good job turning the ally tub to talcum powder! This is the worst of the two but both sides will need repairing.
LR18.jpg
LR18.jpg (344.84 KiB) Viewed 2504 times
My new friend is Mr Hot Air Gun, I've made a good start but there's still more to do. At least the hot air gun keeps you warm on these cold Autumn days. As you can see from the square to the right of the hot air gun, the underseal has done a pretty good job in preserving the underside of the tub which looks to be in good condition.
LR17.jpg
LR17.jpg (357.79 KiB) Viewed 2504 times
Learnt a valuable lesson this weekend, when my daughters boyfriend is giving me a hand with the LWT the wife obliges with cups of tea and bacon butties. When he's not I get nagged at to do other jobs around the house!

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Rebuild of 05 HH 50 GS SIII

Post by AR4412 » Sun Nov 10, 2013 8:19 pm

Hi Shaun,

It looks like the corrosion has won the battle on that part of the tub. :( What are you planning to do? Cut back to solid aluminium and weld a patch in?

Good to see you've made a bit more progress though, have fun with the hot air gun and I hope you don't uncover any more corroded areas. I'm so looking forwards to scraping all the underseal from my tub once its off ,at least when it is I'll be able to see what state the underside is in.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

jsbenson67
Posts: 106
Joined: Wed Jan 25, 2012 6:50 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by jsbenson67 » Mon Nov 11, 2013 4:58 pm

Hi Shaun ,
i'm really interested in your progress, as i plan to rebuild mine onto a galvanised chassis next summer. What makes it more interesting is that only two vehicles separate ours. Mine is 05 HH 47
although its a FFR 24volt. Where did you get yours from? I bought mine in Northern Ireland and it seems to have spent most of its life over there as it have never been registered with Swansea before.
1981 SIII FFR 05 HH 47
1965/66 Sankey Narrow Track Trailer 15 ES 44
2010 Defender 110 XS Station Wagon

Post Reply