Rebuild of 05 HH 50 GS SIII
-
prague1996
- Posts: 113
- Joined: Sun Oct 06, 2013 6:36 pm
Rebuild of 05 HH 50 GS SIII
Only fair that I start a post having been inspired by some of the great rebuilds on the site. Here's a couple of pictures of 05 HH 50 that I bought off ebay.
You can just make out the damage to the front wing which led to it being taken off the road 3yrs ago.
This shows the rotten soft top which blew off on the way home. You can also make out the 'bumperettes' which have been welded onto the rear cross member which needs replacing.
Bulkhead and vent panel are shot on all the usual places, so I have already sent a shopping list to Les (although no reply as yet so I hope I have the right email address?)
A PO has cut the battery tray/oil bath air filter mounts off the chassis and run the battery leads to the rear tub?
I am no mechanic, but my first task last weekend was to see if I could get the engine running. Having replaced the solenoid and after a couple of hours of fiddling the engine fired into life...I was chuffed to bits.
Also managed to get along to the Newbury 4x4 auto-jumble where I met Gordon and managed to pick up some useful spares.
This weekend (weather permitting) I plan to start stripping it down so I can work out how much work the chassis needs.
I'm an enthusiastic novice, so I will need some help along the way!
Bulkhead and vent panel are shot on all the usual places, so I have already sent a shopping list to Les (although no reply as yet so I hope I have the right email address?)
A PO has cut the battery tray/oil bath air filter mounts off the chassis and run the battery leads to the rear tub?
I am no mechanic, but my first task last weekend was to see if I could get the engine running. Having replaced the solenoid and after a couple of hours of fiddling the engine fired into life...I was chuffed to bits.
Also managed to get along to the Newbury 4x4 auto-jumble where I met Gordon and managed to pick up some useful spares.
This weekend (weather permitting) I plan to start stripping it down so I can work out how much work the chassis needs.
I'm an enthusiastic novice, so I will need some help along the way!
Re: Rebuild of 05 HH 50 GS SIII
Hi Shaun,
Congratulations on getting the engine to fire into life. I'm looking forwards to following your rebuild too, it's always good to see people's work and watch the transformation of their vehicles.
Your lightweight's panels look quite straight, apart from the wing, which is always a bonus. Enjoy stripping it down and remember Mr Dremel is your friend when you can't get rusted solid nuts and bolts to come undone.
Check where aluminium panels meet for corrosion, especially where they bolt to steel parts, that's where problems lay waiting for you on the bodywork. On the chassis have a good check all over, especially on any welded seams. Behind the axle bumpstops, especially the rears is a favourite rot spot, as is anywhere from the rear bumpstops backwards, inside and around the rear spring hanger mounts is another of Mr Rust's favourite places to hang out, and the outriggers for the bulkhead and the fuel tanks like to rot. Hopefully you won't find too many problem areas.
Most of all remember to enjoy your time working on the project. There are plenty of us on here who will be more than willing to offer advice if you hit a problem.
Regards,
Congratulations on getting the engine to fire into life. I'm looking forwards to following your rebuild too, it's always good to see people's work and watch the transformation of their vehicles.
Your lightweight's panels look quite straight, apart from the wing, which is always a bonus. Enjoy stripping it down and remember Mr Dremel is your friend when you can't get rusted solid nuts and bolts to come undone.
Check where aluminium panels meet for corrosion, especially where they bolt to steel parts, that's where problems lay waiting for you on the bodywork. On the chassis have a good check all over, especially on any welded seams. Behind the axle bumpstops, especially the rears is a favourite rot spot, as is anywhere from the rear bumpstops backwards, inside and around the rear spring hanger mounts is another of Mr Rust's favourite places to hang out, and the outriggers for the bulkhead and the fuel tanks like to rot. Hopefully you won't find too many problem areas.
Most of all remember to enjoy your time working on the project. There are plenty of us on here who will be more than willing to offer advice if you hit a problem.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
Gordon Bennett
- Maître Pâtissier
- Posts: 7422
- Joined: Sun Jan 10, 2010 12:21 pm
Re: Rebuild of 05 HH 50 GS SIII
You've got a lovely honest looking LWT there.
Looking forward to watching your rebuild too.
Rgds,
Gordon
Looking forward to watching your rebuild too.
Rgds,
Gordon
-
prague1996
- Posts: 113
- Joined: Sun Oct 06, 2013 6:36 pm
Re: Rebuild of 05 HH 50 GS SIII
Neil, thanks for your advice..Mr Dremel is my new friend!
The strip down continues.... Rear panels removed....probably for the first time! Sills removed, have left the seat box in situ but its only held in place by the fuel line running between the twin tanks. Ran out of daylight before I could remove it.
Plan next weekend is to remove the rear tub to get a closer look at the chassis, this is a first for me. Other than the bolts that attach the tub to the rear cross member where else is it fixed to the chassis/out riggers?
The strip down continues.... Rear panels removed....probably for the first time! Sills removed, have left the seat box in situ but its only held in place by the fuel line running between the twin tanks. Ran out of daylight before I could remove it.
Plan next weekend is to remove the rear tub to get a closer look at the chassis, this is a first for me. Other than the bolts that attach the tub to the rear cross member where else is it fixed to the chassis/out riggers?
Re: Rebuild of 05 HH 50 GS SIII
Hi Shaun,
You're further ahead on the stripdown than I am, the rear tub top panels are the next bits off mine once I've got the hard top out of the way.
The rear tub has two mounting points at its front end, shared with the seatbelt stalk mounting bolts, you should see the brackets they bolt through on the chassis crossmember from underneath and there's two bolts either side that pass through the rear fuel tank outriggers.
Your tub looks to be in quite good condition from the pic.
Regards,
You're further ahead on the stripdown than I am, the rear tub top panels are the next bits off mine once I've got the hard top out of the way.
The rear tub has two mounting points at its front end, shared with the seatbelt stalk mounting bolts, you should see the brackets they bolt through on the chassis crossmember from underneath and there's two bolts either side that pass through the rear fuel tank outriggers.
Your tub looks to be in quite good condition from the pic.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
Gordon Bennett
- Maître Pâtissier
- Posts: 7422
- Joined: Sun Jan 10, 2010 12:21 pm
Re: Rebuild of 05 HH 50 GS SIII
Great progress and the tub does look good
My tub looks like a giant has tried to wring it out like a dishcloth
My tub looks like a giant has tried to wring it out like a dishcloth
-
prague1996
- Posts: 113
- Joined: Sun Oct 06, 2013 6:36 pm
Re: Rebuild of 05 HH 50 GS SIII
Thanks Gents...tub does seem pretty straight...it's picked up some extra holes along the way...most notably where a PO has run the battery leads through and the rear near side quarter panel where the number plate was moved to (intend to put it back on the tail gate.
-
Vlaanderen
Re: Rebuild of 05 HH 50 GS SIII
Hi to all,
I've missed something here.........when did the race start?, AR4412, Irish Dave, Daugs and Prague all in a short space of time.
The rebuild threads are going to have some heavy viewing
Keep the piccies coming.
Regards, Norman.
I've missed something here.........when did the race start?, AR4412, Irish Dave, Daugs and Prague all in a short space of time.
The rebuild threads are going to have some heavy viewing
Keep the piccies coming.
Regards, Norman.