Page 1 of 1

jerry can holder

Posted: Tue Jun 11, 2024 3:30 pm
by myhalfyFFR
Good morning, I'm Mauro and I'm writing from Italy, I have a LR lightweight FFR from 1972, I've been following the forum for a few months which in some cases has been useful especially for assembling the radio system. Larkspur.
I recently found a jerry can holder for water jerry cans in a warehouse of an old LR dealer.
From the photos on the web I saw that it is installed on the bulkhead between the two front seats.
Unfortunately I can't find any manuals or drawings that explain how to install it.
I kindly ask the help of the forum members if it is possible to send photos or drawings for assembly.
Thank you very much
Mauro
jerry can holder.jpg
jerry can holder.jpg (53.59 KiB) Viewed 10222 times

Re: jerry can holder

Posted: Tue Jun 11, 2024 4:48 pm
by fv1620
Mauro welcome to the forum. Did you buy that one on ebay as the seller was in Italy?

https://www.ebay.co.uk/itm/153451400040

I have never found any documentation about fitting them. There was recently a thread on HMVF about them & the general view was that they were extremely rare & not often fitted. Someone who claims over the years that he has seen thousands of LightWeights at auction has never seen this holder fitted to a LtWt. Those that had them fitted seemed to be to Rover 8.

Re: jerry can holder

Posted: Tue Jun 11, 2024 7:32 pm
by AR4412
Hi Mauro,

I haven't seen that type of holder before. I have seen a water jerrycan holder fitted to a 109" tub between the seats, in service in the late 80's/early 90's. But, it was of a different design, and IIRC it fitted in the rear tub area and not in the cab, bolting to the rear of the seatback panel. Looking at the angle of the inner pair of mounting legs, I think that it is only designed to fit the 88"/109" tub, as they come up vertically from the seatbox before angling backwards, whereas the lightweight tub is angled backwards right from it's bottom edge at the seatbox.

I wouldn't like to bang my head off of a fuel jerrycan whilst bouncing about off road in the dark. It was bad enough banging against the mounts for the SA80's.

Regards,

Re: jerry can holder

Posted: Tue Jun 11, 2024 8:38 pm
by AR4412
This is the type I was refering to as having seen fitted to 109's in service.

https://www.ebay.co.uk/itm/386642639972 ... R4jt54yBZA

Regards,

Re: jerry can holder

Posted: Wed Jun 12, 2024 10:42 am
by myhalfyFFR
Good morning, thank you all for the welcome and the response, I took the photo from the internet for convenience, I would never have purchased because the asking price is out of the market.
my holder was in a pile of scrap in the workshop of an LR mechanic who was closing his business.
I am sending a photo taken from the internet of the support mounted between the Lightweight seats.
jerrycan4.jpg
jerrycan4.jpg (210.29 KiB) Viewed 10186 times
jerrycan2.jpg
jerrycan2.jpg (96.68 KiB) Viewed 10186 times
jerrycan.jpg
jerrycan.jpg (64.48 KiB) Viewed 10186 times
jerrycan 3.jpg
jerrycan 3.jpg (182.63 KiB) Viewed 10186 times

Re: jerry can holder

Posted: Wed Jun 12, 2024 11:32 am
by AR4412
I did stumble across this one earlier.

https://www.ebay.co.uk/itm/195905929538 ... R8bJpN6BZA

It does look like the green one in your pics..

The other one in the pics looks like the one in your first post, that has possibly had it's legs modified to fit the lightweight.

Regards,