Page 1 of 1

Override mechanism, groove

Posted: Mon Jan 25, 2021 8:03 am
by Fossibear
CBBDBDFF-2F02-40A0-9243-8DE8D29FC165.jpeg
CBBDBDFF-2F02-40A0-9243-8DE8D29FC165.jpeg (93.92 KiB) Viewed 12716 times
in front of the override mechanism there is a groove as shown in the picture.
Can someone tell me please, whether there was something in it like an o- ring or so?
After I pulled out the draughteye I found there only lots of rust...

Kindly regards, Steve

Re: Override mechanism, groove

Posted: Mon Jan 25, 2021 10:29 am
by fv1620
I think you are seeing the cross-sectional view of the circumferential groove for a seal.

Re: Override mechanism, groove

Posted: Mon Jan 25, 2021 10:49 am
by Fossibear
yes, ok, but of what kind was the seal if there was one in there?
Was it rubber?

Regards, Steve

Re: Override mechanism, groove

Posted: Mon Jan 25, 2021 11:09 am
by fv1620
Steve if you tell me the full nomenclature of the trailer I may be able to give you the part number & even cross reference it to specified dimensions.

If you can do that it will save me time looking through lots of trailer parts lists.

Re: Override mechanism, groove

Posted: Mon Jan 25, 2021 5:06 pm
by Fossibear
Hi Clive,

it’s my Sankey NT from about 1968.

Regards, Steve

Re: Override mechanism, groove

Posted: Mon Jan 25, 2021 7:21 pm
by Bob Fell
Fossibear wrote: ↑
Mon Jan 25, 2021 10:49 am
yes, ok, but of what kind was the seal if there was one in there?
Was it rubber?

Regards, Steve
Steve,
The front draught eye seal is felt, part no. FV491002 0.22in w x 0.156 in thk x 5.8 in lg according to the parts manual (but think that should read 0.58 in?),then the one behind the washer key is synthetic rubber 1-5/8in id x 1/8 h(?), no part no. listed. Unobtainable I believe but did see some NOS a couple of years back on gleebay. Clive will hopefully come up with something equivalent (Hi Clive, hope you are keeping well and on air in deepest darkest Wales).
Cheers,
Bob

Re: Override mechanism, groove

Posted: Mon Jan 25, 2021 7:42 pm
by Fossibear
Hi Bob,
thank you very much - perhaps Clive is able to confirm...

Than I am closer to get my Sankey on the road back again.

Stay safe, Steve

Re: Override mechanism, groove

Posted: Mon Jan 25, 2021 11:46 pm
by fv1620
Yes I agree with Bob I think the felt seal should be 0.58 in long
There is a Rubery Owen part number RDSK10222

As for the ring, quite a few part numbers including RAF, RN, as well as Army & a couple of manufacturers.
Trailer ring.jpg
Trailer ring.jpg (77.08 KiB) Viewed 12658 times
(Bob yes on air quite a lot. Had CW contacts today on 80m & 2m, then tonight FM on 4m. Looking forward to tomorrow as heavy rain forecast so I should get out from the valley on 3cm using rain scatter)

Re: Override mechanism, groove

Posted: Tue Jan 26, 2021 6:51 pm
by Fossibear
:D

Thanks to you both - then I’ll try to get it.
Yesterday I was in a MOT point and spoke to the guy who will give me the admittance to use my Sankey on public roads in a allowed way.
We found a way and now I have to work it out.
When it’s ready I’ll show here - to complicated to describe it though it very easy at last...

Regards, Steve