Page 1 of 2

Seat belts

Posted: Sat Oct 01, 2016 11:39 pm
by StuWright
Ok for the moment I am going to stick to fitting the original seat belts and look at inertia if we ever get hold of the correct LR frames.

Before stripping I had a load of make shift reinforcing plates with o rings and climbing shackles. Not good and certainly not safe. I have looked on the parts disc but was unable to see any part numbers.

Does anyone know what I should have seatbelt wise in a 1972 GS and is there a list of fittings so I can just go buy them? Due to time I can't wait around for bits to come up on ebay as I need to work these out in the next week. Thanks in advance for any replies. ;)

Re: Seat belts

Posted: Sun Oct 02, 2016 12:19 am
by removeduser185
Replied in my email

Fred

Re: Seat belts

Posted: Sun Oct 02, 2016 8:27 am
by StuWright
Thanks Fred. :D

Re: Seat belts

Posted: Tue Oct 04, 2016 4:35 pm
by andracav
I need same informations, please ;)
Thanks
Regards
Andrea

Re: Seat belts

Posted: Tue Oct 04, 2016 4:42 pm
by Sidders101
Britax clunk click beautiful brushed chrome classic lumps of machined perfection.....a pain to use but correct for year..expensive to buy...hard to find....reproductions common but still not cheap....personally I'm not fussy about belts..as long as they've got British standard numbers on them they will do...I use static belts...3 point anchor..so easy to fit and can tuck away for display...lap belt for centre.
I can't remember when the inertia belt rear bulkhead framework was introduced in the LWT...so over to you lot.

Re: Seat belts

Posted: Tue Oct 04, 2016 6:51 pm
by removeduser185
andracav wrote:I need same informations, please ;)
Thanks
Regards
Andrea
As Sidders has said, up until around 1980 the Lightweight had static belts. I understand that Britax were the original suppliers. At first, the straps were just that - only straps, later, as with all cars, the short strap was replaced with a stalk to enable them to be done up with one hand. Whether there was ever a lap belt fitted as standard for the centre passenger I don't know, but, I presume there was later on to keep in step with British and European law. Again, as Sidders says, original seatbelts are all but unobtainable, except repro ones through specialist classic car arts suppliers. And they are very expensive.

Fred

Re: Seat belts

Posted: Tue Oct 04, 2016 8:59 pm
by StuWright
Fred wrote:
andracav wrote:I need same informations, please ;)
Thanks
Regards
Andrea
As Sidders has said, up until around 1980 the Lightweight had static belts. I understand that Britax were the original suppliers. At first, the straps were just that - only straps, later, as with all cars, the short strap was replaced with a stalk to enable them to be done up with one hand. Whether there was ever a lap belt fitted as standard for the centre passenger I don't know, but, I presume there was later on to keep in step with British and European law. Again, as Sidders says, original seatbelts are all but unobtainable, except repro ones through specialist classic car arts suppliers. And they are very expensive.

Fred
Anyone know where I could get repro ones from before I go down the Exmoor trim route?

Re: Seat belts

Posted: Tue Oct 04, 2016 9:26 pm
by removeduser185
http://www.johnrichardssurplus.co.uk/me ... 041_14.jpg This is what you are looking for. He's out of stock with the light grey ones, though has dark and they're a bit expensive. But knowing what you're after you can google images and chase up anything which looks close. Holdens and other classic car specialists may also be source.

Fred

Re: Seat belts

Posted: Wed Oct 05, 2016 10:22 am
by andracav
Thanks to all answers!
Andrea

Re: Seat belts

Posted: Wed Oct 05, 2016 12:14 pm
by Jiml
Failing all of the above a visit to a scrap yard might possibly yield results, I have access to an old series ambulance and there were still lap seat belts fitted, not sure of condition but I can go take a look if you like.