Page 99 of 224

Re: Monty the rather rusty 2A - 37FG31

Posted: Sun Jun 25, 2017 5:03 pm
by Gordon Bennett
Hi Andy,

Looks good! What were you watching while you cleaned it?

Sorry i didn't take you up on the welding puns mate. I was going to say you ground me down, but that would start it all over again, so i won't!

Rgds,
Gordon

Re: Monty the rather rusty 2A - 37FG31

Posted: Sun Jun 25, 2017 6:12 pm
by andrewjsimpson1977
Haha I think we need to retire the welding puns Gordon - it's torch-ure enough for people to read this increasingly slow thread without taking time out for cheesy one liners. (There's two in there if you look closely).

We were watching Glastonbury on the telly - which I think you'll agree is better than actually going, as we have hot showers, a fridge and a comfy bed to retire to.

I have to say that despite the progress this week, I'm feeling a little despondent about the project at the moment. I don't seem to be able to finish any one major piece, without hitting a brick wall somewhere along the way. The front axle: I'm waiting for the chrome to finish bubbling off the swivel balls... the steering box: I forgot to order the refurb kit, and the tub: there is so much bodywork to do and it all seems to take forever.

Ah well, onwards and updwards as they say - I'm targeting a balls-fitted-to-axle-case scenario by next weekend, plus the steering box and chassis bracket should be done and refitted to the axle, and ideally one of the holes in the tub filled in.

Keep on truckin' eh?

Andy

Re: Monty the rather rusty 2A - 37FG31

Posted: Sun Jun 25, 2017 6:27 pm
by Gordon Bennett
Hi Andy,

saw them both :D

Take inspiration from Fred and Henry wheeling their chassis out mate.

You're only a few hours behind!

Rgds,
Gordon

Re: Monty the rather rusty 2A - 37FG31

Posted: Sun Jun 25, 2017 7:58 pm
by AR4412
Hiya Andy! :D

Don't get too down about hitting a few hurdles mate, they just add to the overall challenge and working on various bits will stop you going insane as you try and weld the aluminium. I hit a hurdle myself today, but it will be overcome.

Regards,

Re: Monty the rather rusty 2A - 37FG31

Posted: Sun Jun 25, 2017 11:21 pm
by removeduser185
Andy,

Don't despair, mate, we all get like that from time to time. I get it at night when I start totting up the cost of all the bits - it does worry me, as it isn't cheap and, if I had to sell it I'd not get my money back, that's for sure and I sometimes think the cost hasn't been justified. But then, another day and I think, well, think of all the time I spend on it - cheaper than going to football matches or paying to join a golf club.

And, sometimes nothing goes right. Even now on a red-letter day, I'm waiting for a new bolt for the drop arm, because I mashed the thread on the one I had just bought putting it in. I had thought it was in the groove in the shaft - it wasn't and I am a bit ham-fisted at times. Equally, I stripped the thread off the relay securing bolts - that's a tenner each- for nothing! The current batch of paint is the wrong colour, I have the wrong male ends on two of the brake-pipes I ordered so need to get the local garage to change them for me. I have just discovered that two more of the drive flange bolts are stripped - I bought two new ones, but, it seems I needed four, I dropped the engine and smashed a perfectly good dizzy and damaged beyond repair a perfectly serviceable exhaust manifold by snapping off one of the studs... And so it goes on.

The thing is when it gets a bit much, do something else, or have a break. You have plenty of time before the 50th, so don't rush. Better still, have several things going at the same time so if you want an easy half hour job one day cos you're not in the mood, then you have one with a bigger job to do when the time is right. I am finishing the chassis, but, the other day, I was fiddling with the instrument panel. Next I have one or two things to do to the chassis - the PDWA, the brake pipes to finish, but, I might fit the rear bumperettes instead. And, when I start on the tub, I shall also fiddle with the electrics, or the tailboard, or something else - to keep ringing the changes. And I shall build up the vent panel at the same time so I can do something different. But... I do know I have one more damn wheel to do and they are really boring!

Best

Fred

Re: Monty the rather rusty 2A - 37FG31

Posted: Mon Jun 26, 2017 8:25 am
by chipbury
From my desk it looks like you are getting along very well. The nuisance of not having spares to hand is annoying as there ends up being several unfinished assemblies, however when the postie brings the big parcels you can get a few things squared away quite quickly. You then take a big leap forward in the rebuild and your frame of mind leaps up several notches!

Re: Monty the rather rusty 2A - 37FG31

Posted: Mon Jun 26, 2017 9:02 am
by andrewjsimpson1977
Thanks fellas.. I was obviously just having a bit of a wobble - it was a long week and I think subconsciously I expected to have more finished stuff to look at by Sunday evening. You are course right - take a breath and move on.

Ian, thanks in part to your words of support - I have this morning ordered all the remaining parts to finish one side of the front axle, including seals, swivel pins, gaiters, gaskets and tab washers etc. This will be first priority this weekend. The parts to be reused: hub, brake plate, outer housing, swivel ball, drum, end plate, drive shaft, drive member etc are all either pickling away nicely, or sat in degreaser.

Chris: Thanks for the encouraging words matey - means a lot coming from one of the select few members of the 2a Guild :D

All the best,

Andy

Re: Monty the rather rusty 2A - 37FG31

Posted: Mon Jun 26, 2017 6:23 pm
by Gordon Bennett
andrewjsimpson1977 wrote: ↑
Mon Jun 26, 2017 9:02 am
Chris: Thanks for the encouraging words matey - means a lot coming from one of the select few members of the 2a Guild :D
Andy,

I've told you off before about trying to form a splinter group :lol:

Rgds,
Gordon.

Re: Monty the rather rusty 2A - 37FG31

Posted: Mon Jun 26, 2017 6:42 pm
by andrewjsimpson1977
Oh come on Gordon, I woodn't do that to you. Branch off, I mean.

Re: Monty the rather rusty 2A - 37FG31

Posted: Mon Jun 26, 2017 7:24 pm
by removeduser185
andrewjsimpson1977 wrote: ↑
Mon Jun 26, 2017 6:42 pm
Oh come on Gordon, I woodn't do that to you. Branch off, I mean.

Speak to Neil he's the man with the woodcutting skills!

Fred