Page 70 of 224
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 10:30 am
by andrewjsimpson1977
Just a quick update on the other rear hub. This is the one that was repaired as the mating face was damaged.

- IMG_1265.JPG (90.79 KiB) Viewed 1058 times
A quick rub down of the mating face to get rid of the paint over spray, and a thorough clean to remove be any swarf and residual dirt and we are good to go..
Outer race in:

- IMG_1264.JPG (109.84 KiB) Viewed 1058 times
Inner race in:

- IMG_1266.JPG (122.43 KiB) Viewed 1058 times
I also greased and fitted the inner bearing and oil seal, but have stopped there as I need to swap the brake plates over before fitting the hubs to the stub axles. That's a job for the weekend - but for now I'm pleased there is one more job ticked off the list.
Andy
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 4:37 pm
by Macvfork
Nice job on the hub Andy.
I would have put some plasticine in the pits. If you saw my welding you would agree!
Now know mine are/were held on with 3/8 BSF nuts and bolts which is marvellous as I have enough bolts but only 3 nuts.
Back to propshafts then.
Mac
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 5:31 pm
by andrewjsimpson1977
Thanks Mac - repairing the hub face is easy - even if your welding looks like pigeon poo. Its just a matter of blobbing on weld onto the divots in the face, and then grinding it all flat with a spinny sanding pad on a drill. A quick flat off on a level surface with sandpaper on it, and its all done.
Re the fasteners - I got a pack of new nuts and bolts - enough to do a whole axle - for 15 quid
http://www.ebay.co.uk/itm/221758406053? ... EBIDX%3AIT
I have also discovered that i can now only find two of the bolts that go through the end cap / drive member into the hub. Suspect the other four are in my acid dip so will have to go fishing later in the week.
Sometimes I wish i was more organised. You wouldn't think I'm a project manager and requirements guy by trade.
PS - its the same nuts and bolts for the prop shafts, so if you don't have them, you can't fit the prop shafts either.
Sorry
Andy
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 6:51 pm
by Macvfork
Thanks Andy, I will check out the nuts bolts link.
See what you mean on the inner oil seal. Yours defo further in than mine which is flush. Hopefully it makes little difference!
Organised? You? Certainly appears so.
Propshafts-thanks for the bolt info. No gearbox either as still in the wood 5 miles up the valley!
Mac
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 7:07 pm
by andrewjsimpson1977
That doesn't sound the safest storage place to be honest mate. Where in the country are you based? Are you waiting for help to collect it?
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 8:10 pm
by Macvfork
Agreed Andy it's not ideal but that iis how it rolls with the unexpected. No probs picking up, just nowhere better to put it until I get a chassis. Thank you very much for asking. I am south of Tunbridge Wells if you ever are down this way... no sprouts or battenburg!
Bad luck on the end cap bolts. Sadly can't be helpful and say which others might fit, if any.
Mac
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 8:19 pm
by Gordon Bennett
Macvfork wrote: ↑Tue Feb 28, 2017 8:10 pm
no sprouts or battenburg!
Oh dear
Rgds,
Gordon
Re: Monty the rather rusty 2A - 37FG31
Posted: Tue Feb 28, 2017 9:59 pm
by andrewjsimpson1977
Gordon Bennett wrote: ↑Tue Feb 28, 2017 8:19 pm
Macvfork wrote: ↑Tue Feb 28, 2017 8:10 pm
no sprouts or battenburg!
Oh dear
Rgds,
Gordon
Count me out. I have a very strict cake-based belief system which precludes visiting infidels

Re: Monty the rather rusty 2A - 37FG31
Posted: Wed Mar 01, 2017 5:36 am
by Macvfork
What's "preclude" mean!
Re: Monty the rather rusty 2A - 37FG31
Posted: Sat Mar 04, 2017 7:34 pm
by andrewjsimpson1977
Another frustrating day - I managed to strip the other rear spring and get it into acid, and the brake plates and hubs were swapped over following last weekend's bungling efforts. Play was stopped by a pickup of daughter and friends from a kids party, that ended up eating an hour and a half. I came back to find the axle being rained on, so I dried everything out as best I could, nipped up the last few bolts and wheeled the damned thing inside for the night.
I really wanted to get the springs coated and rebuilt this weekend, but events conspired against me. I did try at one point to speed up the de-rusting with my new grinder - but it died almost immediately. Literally caught fire in my hands. Moral of the story is, don't buy cheap grinders.
Tomorrow we are visiting family in staffs, so no play unfortunately.
Harrumph.
If it helps with the photo drought, see below the lovely condition the first leaf spring pieces were in when they came out of the acid. I'm really happy with this - just need the time now to get the bits coated and rebuilt back into spring packs.

- IMG_1295.JPG (125.04 KiB) Viewed 1189 times
All the best,
Andy