FM, What have I done project

Tell us about any of your Land Rover related projects here.
Post Reply
User avatar
StuWright
Master Baker
Posts: 1740
Joined: Wed Feb 24, 2016 11:10 pm
Location: Southampton

Re: FM, What have I done project

Post by StuWright » Sun Dec 11, 2016 9:57 am

Nice work Mac. I have seen loads of rebuild axles with the hammered effect and they go on for years. It will be a great sense of achievement when you get it back together and sprayed. 8-)
Thanks

Stu

55AM52 Ex RAF Land Rover Lightweight GS

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: FM, What have I done project

Post by AR4412 » Sun Dec 11, 2016 10:26 am

Macvfork wrote:Anything else to look for now that I am in there?
Hi Mac,

Looking at the picture of your diff I can't see any abnormal or excessive wear to any of the gear teeth. As long as the oil didn't have any metallic content when you drained it and there isn't any excessive freeplay, in/out, up/down, (bearings), or rotational, (crownwheel/pinion meshing), in the input shaft, or any sideways movement in the crownwheel or planet carrier then I'd say it's good to go back in as it is.

As for my back, it's a case of cracking on. The crippling pain has been replaced with a dull ache so it's either getting better or I'm getting used to it. It's still a bit of a struggle lifting the massive alloys RRS owners insist on fitting on and off, and lifting batteries in and out causes a wince too. Luckily there is no pain when lifting a cup of tea or a bacon sarnie. :D


Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Dec 11, 2016 11:02 am

Thanks Stu,
Not sure whether me getting it back together will result in a sense of achievement or complete surprise!
The beauty of this project , as wise people like you told me at the start, is that everything ends with a sense of achievement with the lows short lived and often forgotten with a bit of lwt parts buying therapy.

In any event it won't stand muster with many of those on here,


Thanks Neil, will have a rootle about in there. Nothing metallic but like a chump chop I forgot to sieve it. Will make up a cradle for it so I can turn the input do-berry.

Chap I worked for many years ago used to do an excellent fruit bat impersonation when his back gave him Jip. took him awhile to get inverted as no remote control hoists back then.
Hope it sorts itself soon.

Mac





Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sat Dec 17, 2016 10:14 pm

Good evening Chaps,
Some knowledge please on my S3 front panel which is a little bit battered. I am wondering if the top line should be straight or if the top line of the outer sections should bend down. The replacement panels suggest they should but not convinced as one side straight other out by 5mm. Perhaps bent to accommodate bonnet angles.

Hub stripped to component parts - all looks good but will change bearings, paint and reassemble.etc.
Attachments
IMG_3671.JPG
IMG_3671.JPG (546.63 KiB) Viewed 1254 times
IMG_3672.JPG
IMG_3672.JPG (759.82 KiB) Viewed 1254 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: FM, What have I done project

Post by andrewjsimpson1977 » Sat Dec 17, 2016 10:51 pm

Loving the measuring device.

I'm afraid (assuming your 'straight rule' is actually straight) - the panel is bent.

Go at it with some hammers though - they can be resurrected from worse than that.

Andy

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Dec 18, 2016 6:04 am

andrewjsimpson1977 wrote:Loving the measuring device.

I'm afraid (assuming your 'straight rule' is actually straight) - the panel is bent.

Go at it with some hammers though - they can be resurrected from worse than that.

Andy
Thanks Andy. Guessing it had an impact on that corner as the angle below (hip) has overlapped slightly. Will have to cut and weld I guess. Straight edge is a lovely old cast spirit level.

Have you been with your chassis all night? Much looking forward to reading of your progress.

Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: FM, What have I done project

Post by andrewjsimpson1977 » Sun Dec 18, 2016 8:52 am

I have resisted the urge to go out again so far - but i am feeling motivated again all of a sudden :D

I need to do the same thing to my axles and springs as you have - so keen to get the thing back onto its wheels. I also decided last night i am going for 7.50 tyres so that means i suddenly need to find some 5.5 rims.

Hey ho..

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Dec 18, 2016 12:01 pm

S3 NSR hub exploded less brake bits.

Heard some talk here about the collar? at the base of some stubs needing to be removed presumably due to wear. Involved drilling I believe. Mine does not appear to be of removable type and all seems as it should. Can anyone advise otherwise or good to go?
Thanks
Mac

Ps. Anyone recognise the inspector?
Attachments
IMG_3692.JPG
IMG_3692.JPG (553.49 KiB) Viewed 1229 times
IMG_3693.JPG
IMG_3693.JPG (825.37 KiB) Viewed 1229 times
IMG_3690.JPG
IMG_3690.JPG (935.78 KiB) Viewed 1229 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Tue Dec 20, 2016 9:06 pm

An exciting few days as plucked up the courage to remove the bulkhead which is pretty messy but salvageablejustneeds a couple of footwells, hinge plates, a leg and the box engine side of centre console. Pleasantly surprised how easy it was except the water temp sender which had to be snipped!

Attempted to straighten front panel but not too good so will need redoing.

Stripped rear axle ready for painting after welding in repair plates to reinforcing sections, spreads for hubs arrive Thursday. Surprised to see two different sized bearings in each hub which I now understand makes it pre 1980.

Prepped and painted front number plate bracket in anticipation of mil reg plate turning up on Sunday.

In an unorthodox fashion removed front axle and suspension. Blooming heavy! Leaves appear too far gone but will see once separated and cleaned how much metal actually remains.
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Tue Dec 20, 2016 9:13 pm

on axle with Rover ahocks. Not sure if some bits welded on by ns u bolts should be there or not.
Attachments
IMG_3732.JPG
IMG_3732.JPG (938.73 KiB) Viewed 1207 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Post Reply