44AJ20 & 93KA28 Rebuild Barbados

Tell us about any of your Land Rover related projects here.
User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Gearbox Overhaul: Chassis Installation

Post by weetchus » Wed May 12, 2021 6:03 pm

Another milestone reached. Gearbox is in, bolted in place and stands supporting the engine are now gone. It is a rolling chassis once more.
All the gears change quite smoothly so that is a result.
Screen Shot 2021-05-12 at 1.01.33 pm.png
Screen Shot 2021-05-12 at 1.01.33 pm.png (3.23 MiB) Viewed 1256 times
Screen Shot 2021-05-12 at 1.03.07 pm.png
Screen Shot 2021-05-12 at 1.03.07 pm.png (2.45 MiB) Viewed 1256 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Body: Rolling again

Post by weetchus » Mon May 17, 2021 7:01 pm

It's been months since the Lightweight moved as the engine was only supported by its two stands on the chassis and 2 jack stands underneath. Now the gearbox is in, I was able to roll it out into the light and my kids rolled around on skateboards underneath with paintbrushes dusting volcanic ash away :lol:
Screen Shot 2021-05-17 at 1.49.47 pm.png
Screen Shot 2021-05-17 at 1.49.47 pm.png (2.81 MiB) Viewed 1224 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Body: Test fitting body panels

Post by weetchus » Mon May 17, 2021 7:12 pm

I was checking the bulkhead to radiator panel dimensions by installing the bonnet and then go carried away with the rest.
Thankfully it all seems to fit... though it all has to come off for some crack repairs and some minor painting on the spots where the aluminium has been in contact with steel. But the external paintwork will stay the same. I will only be painting the seat box, seat back on tub and insides of the doors to make inside nice and pretty, while the outside stays looking... historical. haha.
Screen Shot 2021-05-17 at 1.50.27 pm.png
Screen Shot 2021-05-17 at 1.50.27 pm.png (2.85 MiB) Viewed 1223 times
Screen Shot 2021-05-17 at 1.51.04 pm.png
Screen Shot 2021-05-17 at 1.51.04 pm.png (2.9 MiB) Viewed 1223 times
Screen Shot 2021-05-17 at 1.51.29 pm.png
Screen Shot 2021-05-17 at 1.51.29 pm.png (2.7 MiB) Viewed 1223 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Carburettor: Weber rebuild

Post by weetchus » Mon May 17, 2021 7:20 pm

A Weber rebuild kit for my Weber 34 ICH and Ducellier Distributor kit arrived in Barbados.
So I rebuilt the Weber for the 2nd time. The first time was just to deep clean in prep for the new kit.
Screen Shot 2021-05-17 at 1.51.37 pm.png
Screen Shot 2021-05-17 at 1.51.37 pm.png (3.29 MiB) Viewed 1223 times

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Distributor: Service Kit

Post by weetchus » Mon May 17, 2021 7:22 pm

I then did the Ducellier Distributor. New rotor arm, cap and points.
I'm hoping the other parts are all okay.
Screen Shot 2021-05-17 at 1.51.49 pm.png
Screen Shot 2021-05-17 at 1.51.49 pm.png (1.15 MiB) Viewed 1223 times

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by Loulou » Tue May 18, 2021 4:52 am

Perfect,

All this is moving in the right direction and preparing for the beautiful season… ?!

Warning: to adjust the body, you must start from the rear and therefore the tub in place bolted to the rear cross member.
It is only then and according to the dimensions useful for a good opening of the doors and the respective squares that you "slide" the bulkhead back and forth. You will notice that the two supports connecting the bulkhead to the frame each have three oblong holes in the lower part allowing about 15mm of displacement.

Regards
Looloo
Capture d’écran 2021-05-18 à 05.48.59.png
Capture d’écran 2021-05-18 à 05.48.59.png (223.99 KiB) Viewed 1210 times
Capture d’écran 2021-05-18 à 05.48.31.png
Capture d’écran 2021-05-18 à 05.48.31.png (102.1 KiB) Viewed 1210 times
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Tue May 18, 2021 3:03 pm

Thanks LooLoo
I am working on the doors at the moment so that I can properly align the tub, doors and then the bulkhead as you suggest. Thanks for mentioning the oblong holes as I had forgotten about them and this saves me time!

User avatar
Loulou
Pastry Chef
Posts: 570
Joined: Wed Jul 04, 2018 12:12 pm
Location: France

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by Loulou » Tue May 18, 2021 5:40 pm

Hi,

And for the 2x three fasteners of these oblong holes, the bolts are on the outside face of the frame side member and the nuts on the inside side of the side member.
Otherwise, you risk not having enough room on the left side between the starter and the support to slide the three long bolts ...

Regards.
LL
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)

Foz31
Posts: 176
Joined: Mon Mar 06, 2017 7:10 pm

Re: Body: Rolling again

Post by Foz31 » Wed May 19, 2021 11:15 am

weetchus wrote: ↑
Mon May 17, 2021 7:01 pm
It's been months since the Lightweight moved as the engine was only supported by its two stands on the chassis and 2 jack stands underneath. Now the gearbox is in, I was able to roll it out into the light and my kids rolled around on skateboards underneath with paintbrushes dusting volcanic ash away :lol:

Screen Shot 2021-05-17 at 1.49.47 pm.png
Good work re the kids - modern equivalent of sending them up the chimney 😉
25HF03 Series III 200Tdi

User avatar
weetchus
Pastry Chef
Posts: 676
Joined: Wed Aug 15, 2018 3:15 pm

Re: 44AJ20 & 93KA28 Rebuild Barbados

Post by weetchus » Thu May 20, 2021 3:41 pm

Thanks again LooLoo. WIll do exactly as you suggest.
Foz31, the kids have to start being useful sooner rather than later right? I can't wait for the fun we are all going to have with the Lightweight.

Post Reply