Tell us about any of your Land Rover related projects here.
-
AR4412
- Maître Pâtissier
- Posts: 8938
- Joined: Thu Sep 22, 2011 9:31 am
- Location: Bedford
Post
by AR4412 » Sun Sep 06, 2015 6:52 pm
Hi Andy,
Nice to see you're cracking along with the stripdown.
That bumper looks like it could be a teaser to straighten. Sorting the ends isn't too bad, as mentioned hooking it to something and pulling the ends back out works, so does taking it off and driving over it. You may be able to pull the centre a bit straighter by pulling it with a strong rope with a hook on the underside and another vehicle on the other end, but I have a feeling you may need heat and a big hammer to get it fully straightened.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Post
by andrewjsimpson1977 » Sat Sep 19, 2015 6:53 am
Last weekend - Did a few hours of disconnecting bits from the bulkhead (on both sides).
Managed to get the main dash panel out, and one of the aux panels. Discovered that lightweights have a nest of wiring resembling spaghetti junction. At least mine does!
Also got a few bits stripped from the engine bay (distributor cover and HT leads off, more oil pipes disconnected, fuse box & voltage regulator out, coil disconnected, that sort of thing)
It feels like slower and slower progress each time at the moment, but i'm getting there bit by bit.
-
Attachments
-

- thumb_img_2643_1024.jpg (70.07 KiB) Viewed 3393 times
-

- thumb_img_2630_1024.jpg (65.54 KiB) Viewed 3393 times
-

- thumb_img_2653_1024.jpg (69.66 KiB) Viewed 3393 times
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Post
by andrewjsimpson1977 » Sat Sep 19, 2015 6:54 am
Back of clocks are a tad rusty!
-
Attachments
-

- thumb_img_2625_1024.jpg (45.36 KiB) Viewed 3392 times
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Post
by andrewjsimpson1977 » Sat Sep 19, 2015 7:17 am
This weekend I decided to try again to get the tub off - to no avail.
The two front bolts which go through the angled supports (i think for seat belts i don't have) are seized solid. Waiting for new grinder and reciprocating saw to arrive to deal with the issue.
So - on with the bits i can do..
Driver's side floor - out
Driver's side petrol tank - out
Four wheel drive selector adjuster nut - snapped off while trying to remove - added to list of things i need to replace
Steering wheel nut - wont budge. I noticed in another project thread that the best approach seems to be to drill two holes in the nut at 180 degrees above and below the column and split with a chisel, so will try that next time.
-
Attachments
-

- thumb_img_2737_1024.jpg (56.28 KiB) Viewed 3388 times
-

- thumb_img_2740_1024.jpg (79.32 KiB) Viewed 3388 times
-

- thumb_img_2739_1024.jpg (59.76 KiB) Viewed 3388 times
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Post
by andrewjsimpson1977 » Sat Sep 19, 2015 7:22 am
Last job of the day...
OK i've had loads of (really sound) advice regarding the vent panel.
I want to start by saying i respect the opinion of the people on here who advised that this panel is shot, and it is much more sensible to replace.
Two points on this:
1) I don't currently have £500 spare for a new one
2) I've never been that sensible
So i decided to cut out / wire-brush off as much of the loose rust as possible, and rust-kill the rest chemically.
Then I'll see if enough is left for a repair.
Hmm...
-
Attachments
-

- thumb_img_2736_1024.jpg (67.41 KiB) Viewed 3387 times
-
norcoatomique
- Master Baker
- Posts: 1311
- Joined: Wed Mar 10, 2010 5:30 pm
- Location: Faringdon Oxfordshire
Post
by norcoatomique » Sat Sep 19, 2015 10:19 am
good luck, hope you manage to save the vent panel. its worth trying. D.

Certa Cito.
-
BOMBER71
- Pastry Chef
- Posts: 524
- Joined: Thu Jul 25, 2013 12:47 pm
- Location: BLANDFORD DORSET
Post
by BOMBER71 » Sat Sep 19, 2015 10:51 am
Hi Andy , That looks an interesting project you have there and thanks for posting the pictures . I had a very rusty vent panel on my 2a project so I sent it to the guy in Ireland who often sells refurbished/galvanised vent panels and bulkheads on ebay under the name "Hairy monster". He refurbished and galvanised mine for £150 inc the return postage . He did an excellent job but turn around time was slow ! Where in the country are you based ? Regards Martin
series 2a lightweight 40 FG 24. Landrover wolf 90 LN 92 AA Landrover 101 24v FFR 74 FL 87 EX 12AD RAPIER LAUNCHER. Landrover 101 12v RHD 73 FL 30 EX 7 PARA
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Post
by andrewjsimpson1977 » Sat Sep 19, 2015 12:02 pm
norcoatomique - just been reading your projects - how many lightweights do you have?! sheeesh!
Bomber - I'm in Bedfordshire. £150 sounds like i need to speak to that guy! I think given that repair sections will likely cost me around 50 quid, plus welding (i can't yet so would have to get someone in), plus blasting, plus galv-ing - if your man in Ireland can do mine for anything like the cost of yours...i'm in! Do you have contact details?
Also I noticed in your restoration thread that you had your seats done in Cheshire - that's where i'm from and regularly go back to visit my folks - is there a trimmers there you would recommend?
Thanks as always to all who have commented / advised - i'm new to land rovers, and this is a voyage of discovery for me virtually every day, so i really do appreciate the input of others
: )
-
Dickyboy
Post
by Dickyboy » Sun Sep 20, 2015 8:24 am
Don't get downhearted you will have lows but there are more highs as you progress with your restoration look at what you can achieve and selfie that smile when you are driving her around
-
chipbury
- Master Baker
- Posts: 1411
- Joined: Sun Oct 02, 2011 3:26 pm
- Location: Bath
Post
by chipbury » Sun Sep 20, 2015 5:08 pm
That's good progress you've made there recently.
I've seen bombers vent panel and it looks very nice.
2A - 39 FG 70