What have you done to or with your LWT today??

Any Land Rover related info can be posted here.
that man
Posts: 95
Joined: Thu Mar 22, 2018 8:13 pm
Location: Cheshire WA7

Re: What have you done to or with your LWT today??

Post by that man » Mon Nov 12, 2018 7:00 pm

Hi Kev I am about to ( well soon as the plans garage etc is done) start a rebuild and I believe that you have some of the best support possible in this forum from men that care so chin up I will need your support soon for 45-AJ-03 So chin up it's the journey as they say.

Treehugger

Re: What have you done to or with your LWT today??

Post by Treehugger » Mon Nov 12, 2018 9:28 pm

I ain't giving up on the LWT but its still giving me a headache.
Yesterday (Sunday PM) I stripped out the pick up pipe from the tank to check for a blockage (part blockage that is) and found it to be perfectly okay. Not one bit of muck anywhere. I noted on eBay that a similar pick up pipe had what looked like a filter tied around the end. Whether this is correct or not I don't know. Anyone else care to comment?
I also changed the pick-up pipe gasket over as it was a totally shot rubber type and splitting badly. I have several spare gaskets of the cork and rubber compound variety so nothing wasted there. I'm still waiting for the new tank to dry off after its coat of Waxoyl underseal which I applied on Sunday. Once dry then sometime soon I hope to fit it but time and weather will decide.

I also cleaned all the contact points and earth for the sender unit and refitted all the fuel lines (minus the two-way tap of course as its still not playing ball). Whilst doing so I found a pipe under the seat that wasn't connected properly. My fault obviously as it was only slammed together without tools when the two-way tap played up after I'd replaced the gasket in it some time back. However I clearly forgot to re-tighten it up properly after that and although it never gave me any problems at the time it definitely needed sorting. Having decided that it might have been the connection causing the issues I fired up the LWT with no problem at all. Looking good thinks I. Too late for a test run yesterday so I took it out today for a quick test run to see if I had somehow miraculously sorted out the issue.

Wrong! Still running on kangaroo fuel after a couple of miles.

So this afternoon I started stripping the carb again so I can refurbish the jets and stuff. Bought one of those refurbishment kits from Paddocks recently when I bought the replacement petrol pump so now I'm doing the work I could have done the first time around. This despite it having no clear sign of malfunctioning after I'd cleaned it out after Halford's finest dragged the crap through from the tank when they ran it out of petrol. Although to be fair that was as much my fault for not going there with a lot more fuel in the tank to begin with.
Anyway I don't know if I mentioned this before but I did get it to the MOT station at Halford's this Saturday afternoon after I had received the replacement fuel pump and outlet pipe earlier than expected on Friday. It passed as expected. Well it was only a slightly loose wheel bearing after all and there wasn't anything else wrong with it. I also sorted out the oil leak on the petrol pump and the distributor on Friday too. Odd thing was that whoever had removed the petrol pump in the past had neglected to refit it with any gasket. Yes it was completely missing....apart from a small torn section of the original still stuck to the original pump base. No wonder it was leaking oil..
And another thing I found was the rubber 'O' ring at the base of the distributor had given birth obviously as there were two 'O' rings and both over size for the groove in the distributor. I won't point fingers but clearly someone made do with what they had despite it being the wrong size and they slapped a load of red Hylomar all over the two 'O' rings to seal the distributor base. Made a right mess of it. Anyway I haven't got the right size 'O' ring either so made do temporarily with a similar fix until I can get a couple delivered.

So the mystery Kangaroo colony is still lurking in the LWT somewhere and I haven't found a single clue as to where they are. Still hunting. Only thought I had was the vacuum advance and retard pipework and diaphragms might be at fault. Will know soon enough with the carb as the kit has a couple of replacements. Fingers crossed.

chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: What have you done to or with your LWT today??

Post by chipbury » Tue Nov 13, 2018 5:15 am

The main thing is you have the MOT now :!
As for the fuel issues I’m sure you’re on the right track. I had a few carburettor problems on mine after the rebuild (in fact I still carry a cheap copy carb as an onboard spare!).
2A - 39 FG 70

User avatar
Bob Fell
Cake Guru
Posts: 3044
Joined: Wed Sep 18, 2013 7:17 am
Location: Melton Mowbray

Re: What have you done to or with your LWT today??

Post by Bob Fell » Tue Nov 13, 2018 6:23 pm

Kevin,
The tank fuel pick up pipe (NRC6905) should have a fluted filter mesh brazed to the end of it.
See here, unfortunately pics not very good;
https://www.johncraddockltd.co.uk/_imag ... 58-84-.jpg
https://www.google.com/url?sa=i&rct=j&q ... x=3&uact=3
You can buy the filter separate and sweat it or braze it on yourself.
Bob
042Bobf


19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.

User avatar
Bob Fell
Cake Guru
Posts: 3044
Joined: Wed Sep 18, 2013 7:17 am
Location: Melton Mowbray

Re: What have you done to or with your LWT today??

Post by Bob Fell » Tue Nov 13, 2018 7:07 pm

Landie68 wrote: ↑
Mon Nov 12, 2018 6:00 pm
Frustration time yet again. Original fuel gauge contained more rust than useful working parts, so I purchased a brand new one, which worked if you didn't mind the fact it only had 3 settings, full, 3/4 full or empty and these came at random times depending on the bounce of the lwt.
Now it has finally decided to refuse to move off the E point, so I guess another gauge is going to be needed, grrrrrrrr
After a rather wallet emptying weekend, second fuel tank leak, the tank has been sealed with POR15, yet to see how well petrol stays inside the tank rather than on the garage floor. :roll: :roll: :roll:
Richard,
I would look at the tank sender units, changeover switches on the tap and wiring continuity before you do that.
Regards
Bob
042Bobf


19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.

Treehugger

Re: What have you done to or with your LWT today??

Post by Treehugger » Tue Nov 13, 2018 10:20 pm

Bob Fell wrote: ↑
Tue Nov 13, 2018 6:23 pm
Kevin,
The tank fuel pick up pipe (NRC6905) should have a fluted filter mesh brazed to the end of it.
See here, unfortunately pics not very good;
https://www.johncraddockltd.co.uk/_imag ... 58-84-.jpg
https://www.google.com/url?sa=i&rct=j&q ... x=3&uact=3
You can buy the filter separate and sweat it or braze it on yourself.
Bob
Ah! Now that explains the solder/brazing marks about 2" from the end which I thought were an attached extension for different depth of tank but it fits with it being the remains of something brazed onto the pipe. I will have to get hold of one of those fluted filter meshes and get it fitted. Might be a good excuse to buy a brazing torch I had my eyes on. Have a load of stuff to fix. Thanks for the info once again.

Treehugger

Re: What have you done to or with your LWT today??

Post by Treehugger » Tue Nov 13, 2018 10:34 pm

chipbury wrote: ↑
Tue Nov 13, 2018 5:15 am
The main thing is you have the MOT now :!
As for the fuel issues I’m sure you’re on the right track. I had a few carburettor problems on mine after the rebuild (in fact I still carry a cheap copy carb as an onboard spare!).
Your so right there. The MOT was the main issue to begin with. I knew it would pass but it was simply getting it to the retest that was holding me up. Now I can tinker at my leisure so to speak and get the carb refurbished properly. Its almost done but had to abandon it to go into town on another mission.
Tomorrow I take my main motor in to part ex for its new replacement so tomorrow is already taken up. The day after I collect my new motor but provided its ready early enough I may get the carb finished. Only got the main air flap seals and rubbers to replace and then top fitting back to the bottom bit and its done. Gave all the jets and fuel ways a good blast out with an air can and it shifted a few bits of dirt. Nothing seems to be obviously wrong with it but I have a feeling that the diaphragms in the carb will benefit from replacement. All in all it will be another job ticked off the list and one step closer to solving the problems.

If that isn't the issue I intend to drive it until it repeats the kangaroo impressions and stop. Then check the fuel filter to see if any petrol remains in there and also use my temperature gauge to see if the coil is overheating as was mentioned by Clive I think with respect to Fred's LWT.

One solution to eliminate the tank side of the system was suggested to me by a neighbour. Get a petrol can, a 1 gallon plastic thing will suffice, stand it in the passenger foot well and fit a temporary pipe through the bulkhead (plenty of places for a pipe to feed through) and connect it to the inlet pipe of the sediment trap. Drive off and see if the vehicle repeats the same habits. if it does the problem is not the tank side as the temporary fuel tank should be totally foolproof. If it doesn't behave the same refit the pipe to the correct fuel tank and drive again and see if the LWT kangaroos along. It won't pin point the fault precisely but it does offer a way to reduce the search area quite a bit. I'm also going to order a replacement inlet fuel line while I'm on that circuit just in case it has a slight hole in it between the tank and the sediment trap.

Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Re: What have you done to or with your LWT today??

Post by Landie68 » Tue Nov 13, 2018 11:46 pm

Bob Fell wrote: ↑
Tue Nov 13, 2018 7:07 pm
Landie68 wrote: ↑
Mon Nov 12, 2018 6:00 pm
Frustration time yet again. Original fuel gauge contained more rust than useful working parts, so I purchased a brand new one, which worked if you didn't mind the fact it only had 3 settings, full, 3/4 full or empty and these came at random times depending on the bounce of the lwt.
Now it has finally decided to refuse to move off the E point, so I guess another gauge is going to be needed, grrrrrrrr
After a rather wallet emptying weekend, second fuel tank leak, the tank has been sealed with POR15, yet to see how well petrol stays inside the tank rather than on the garage floor. :roll: :roll: :roll:
Richard,
I would look at the tank sender units, changeover switches on the tap and wiring continuity before you do that.
Regards
Bob
All have been double checked Bob to the extent that I have had the fuel gauge off and attached direct to the battery and earthing direct back to the battery and it still won't move
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

User avatar
Bob Fell
Cake Guru
Posts: 3044
Joined: Wed Sep 18, 2013 7:17 am
Location: Melton Mowbray

Re: What have you done to or with your LWT today??

Post by Bob Fell » Wed Dec 19, 2018 8:46 pm

Today being the first day of the Christmas holidays for me, the weather has been kind, sunny, about 10C, so I set about doing part of my annual servicing, plugs out, cleaned and gap checked plus a check on the air filter oil bath.
011.jpg
011.jpg (2.42 MiB) Viewed 2710 times
With the Jolley Engineering electronic ignition I have found the optimum plug gap using Lodge plugs is 1.1mm, Jolley recommends between 1.0mm and 1.2mm.
005.jpg
005.jpg (2.55 MiB) Viewed 2710 times
007.jpg
007.jpg (2.73 MiB) Viewed 2710 times
Pics are a bit iffy due to the sun and my crap mobile.
That's about it for the year.
Regards
Bob
042Bobf


19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: What have you done to or with your LWT today??

Post by removeduser185 » Sat Dec 22, 2018 7:29 pm

Bob Fell wrote: ↑
Wed Dec 19, 2018 8:46 pm
Today being the first day of the Christmas holidays for me, the weather has been kind, sunny, about 10C, so I set about doing part of my annual servicing, plugs out, cleaned and gap checked plus a check on the air filter oil bath.

With the Jolley Engineering electronic ignition I have found the optimum plug gap using Lodge plugs is 1.1mm, Jolley recommends between 1.0mm and 1.2mm.

Pics are a bit iffy due to the sun and my crap mobile.
That's about it for the year.
Regards
Bob
That's a good-looking engine there, Bob. I am hoping to get the first 500-mile service done in the next couple of weeks, if it stays dry long enough for me actually to get in the garage. I look forward to seeing your Land Rover in the flesh in 1919, all being well and, as a bonus, it would be nice to have mine with me at the same time!

Post Reply