Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Wed Oct 24, 2018 10:25 pm

Andy, your MIG welding is a lot lot lot better than my TIG welding on my front wing! I am so ashamed of it that I won’t be posting until I have cleaned it up a fair bit and had a lot more practice!
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu Oct 25, 2018 8:35 am

Matt's landy wrote: ↑
Wed Oct 24, 2018 9:23 pm
Nice to see the progress as it goes back to original, mine
(37FG35) had been seriously molested before I had it although what was there was good so I built it up as a toy and just retained as much 2a as I could, my main aim to save it from the garage it had been in for 20 years plus in pieces, I have a copy of the microfiche build dates from land rover , chassis numbers 481-505 if yours falls into those, happy to email you a photo of it to put with yours if your interested

Matt
Thats very kind Matt - yes please! Mine is 494 so it should be on there!

Email is [email protected]

Any photos of yours would be interesting too.

Thanks again,

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu Oct 25, 2018 8:39 am

landylees wrote: ↑
Wed Oct 24, 2018 10:25 pm
Andy, your MIG welding is a lot lot lot better than my TIG welding on my front wing! I am so ashamed of it that I won’t be posting until I have cleaned it up a fair bit and had a lot more practice!
I tried ally welding with the MIG on my tub. It looked like a Somme reenactment by the time i had finished - off to the fabricators I will now go for some replacement panels!

Best of luck with the TIG mate, you flash bugger :D

landylees
Pastry Chef
Posts: 639
Joined: Mon Jan 29, 2018 8:43 pm
Location: Bishops Stortford

Re: Monty the rather rusty 2A - 37FG31

Post by landylees » Fri Oct 26, 2018 9:01 pm

andrewjsimpson1977 wrote: ↑
Thu Oct 25, 2018 8:39 am
landylees wrote: ↑
Wed Oct 24, 2018 10:25 pm
Andy, your MIG welding is a lot lot lot better than my TIG welding on my front wing! I am so ashamed of it that I won’t be posting until I have cleaned it up a fair bit and had a lot more practice!
I tried ally welding with the MIG on my tub. It looked like a Somme reenactment by the time i had finished - off to the fabricators I will now go for some replacement panels!

Best of luck with the TIG mate, you flash bugger :D
Having spent most of the week on and off trying to TIG weld I have now given up before I cause irreparable damage to the wing - I will be leaving it in the hands of an expert on Monday. I am quite annoyed as I have been on a TIG welding course when I could weld and have now "achieved" very poor welds - whilst doubting my "skills" I am also doubting my 2nd hand TIG as it regularly trips the RCD (even though it has been moved off the RCD circuit) and it is very difficult to strike an arc with HF. Anyway, I don't want to spend any more time on it so off to a proper welder on Monday.
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]

aerialphil
Posts: 136
Joined: Sun Apr 22, 2012 12:43 pm

Re: Monty the rather rusty 2A - 37FG31

Post by aerialphil » Sun Oct 28, 2018 8:31 pm

Forget the wd40 and use a decent propane blow lamp/Also mix up some nail varnish remover and brake fluid as brilliant penetrating oil. As for the chassis if it's peppered with holes after sand blasting it will be thin in many other area's you can't see and will have lost a lot of it's strength. This deserves a 2 grand designa chassis with 3mm center rails. I had one made by designa and it is excellent. Galv is also good. very strong and lowers the center of gravity slightly, Plus when painted to stop scum bags following you home to nick it. you can forget the rust problems with the chassis Phil

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Nov 07, 2018 4:25 pm

I think you may be a few posts behind Phil - its already had a new chassis :D

So.. today come with a grump advisory rating of 9 on the 'Harrumph!' scale.

I got a reasonable way through the welding, just to have the swan neck on the torch completely (and impenetrably) block with melted wire. What the hell! I have a spare swan neck but the fittings are wrong (an older type apparently...grrr!!).

Decided *&%! it I'll buy a whole new torch. Its in the post. I am in the beer cupboard.

On the good news front, I ordered the exhaust, so that'll be going on over the next week or so. Also, I managed to secure a new job, which I think you'll agree is always helpful. Due to the job, and for reasons I won't discuss here, I've had to delete all my social media accounts - so that should un-clutter my life a bit at least.

I'm sat here with all the anti rust stuff, metal and paint i need to finish the bulkhead, all the free time in the world while I wait for the new job to start, and no working welder - bloody typical!

Thats it for now,

Andy

chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Wed Nov 07, 2018 5:10 pm

Congratulations on the new job, hopefully the torch will turn up soon for you to use the downtime sensibly. For gods sake don’t get caught up in anything foolish like household chores, gardening or decorating in the meantime.
I’ve just endured 5hrs of death by PowerPoint, thankfully they are giving us free beer tonight to make up for it :D . What could possibly go wrong...
2A - 39 FG 70

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Wed Nov 07, 2018 6:09 pm

Hiya Andy! :D ,

Sorry to hear that the gremlins have got into your welder mate. If you want to borrow my MIG to keep you going until your new torch arrives you can. If you want to pick it up just let me know. My not so smartfone is refusing to make or take calls, but I can still be contacted by PM or text.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Nov 07, 2018 9:36 pm

AR4412 wrote: ↑
Wed Nov 07, 2018 6:09 pm
Hiya Andy! :D ,

Sorry to hear that the gremlins have got into your welder mate. If you want to borrow my MIG to keep you going until your new torch arrives you can. If you want to pick it up just let me know. My not so smartfone is refusing to make or take calls, but I can still be contacted by PM or text.

Regards,
That’s a kind offer mate thank you. I’ll have a look when the order gets updated with a delivery date, and maybe if it will be a while I’ll drop in over the weekend some time. I have a few other jobs to be getting on with - no Chris, not housework don’t worry!

I’m going to clean up the rest of the goalpost and anti-rust treat and prime it,so I’m only then looking at the bits that need repairing / building up. Plus hopefully the exhaust will arrive soon so plenty to be getting on with.

Andy

Jiml
Pastry Chef
Posts: 644
Joined: Sat Jul 18, 2015 1:56 pm
Location: Burnley Lancashire
Contact:

Re: Monty the rather rusty 2A - 37FG31

Post by Jiml » Thu Nov 08, 2018 1:51 pm

Social media can be good but if your usename is blowjob69 it could make a difference at the job interview, some companies do look at that kind of thing As Sidders will tell you he took down RAF regiment are great, but of course totally unbelievable (Sorry Bob) :)
52HG42 my current love interest

Post Reply