Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sat Oct 20, 2018 9:43 pm

As you say, Andy, it is a good start. I'm impressed. Once you've ground the welds down, I think it will look fine. I was surprised how rough the joints were on my original bulkhead - and are still on the replacement. But, once in place, painted and with the instruments etc in place, the welds aren't particularly obvious anyway.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Oct 21, 2018 5:16 pm

Thanks Fred - hopefully the functional but ugly welding will smarten up nicely with the grinder.

Today was about 30 of these:

A7ED934A-DF7A-4C60-9BB7-82C07AB04D88.jpeg
A7ED934A-DF7A-4C60-9BB7-82C07AB04D88.jpeg (758.22 KiB) Viewed 2202 times

And so it went on..

6E9A6E35-234B-4C47-B94F-C49FEF0C4320.jpeg
6E9A6E35-234B-4C47-B94F-C49FEF0C4320.jpeg (966.67 KiB) Viewed 2202 times

Followed by about 30 of these, moving the clamps each time to make sure the sheet was as tight to the frame as possible:

6313DAC2-114D-433B-917C-26AF325FDE2C.jpeg
6313DAC2-114D-433B-917C-26AF325FDE2C.jpeg (1.46 MiB) Viewed 2202 times

As before the weld are quite ugly, mainly due to the brown by-product of the flux cored wire, but the welds are strong, and it just means a little dressing back with Mr A.Grinder. Well, ok..hours and hours of it.

The plug welds were ground down most of the way, but will be finished off with a sander. This way there is less risk to gouging the panel itself with the aggressive grinder flap disc thingies.

0FB42BD6-2185-4046-A264-F8170718FFEC.jpeg
0FB42BD6-2185-4046-A264-F8170718FFEC.jpeg (919.86 KiB) Viewed 2202 times

It’s going to be a long job to get this bulkhead back together. I don’t know if I am just a) crap at welding or b) too much of a perfectionist but it seems to take me ages to get around it all. Still, at least I should end up with a nice solid finished bulkhead eventually.

Will try to get another load done tomorrow evening, time permitting.

All the best,

Andy

chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Sun Oct 21, 2018 9:09 pm

Lovely, lovely - at this rate you will take the Sunday evening not paying attention to what the wife is watching welding porn award.
2A - 39 FG 70

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Oct 21, 2018 9:40 pm

chipbury wrote: ↑
Sun Oct 21, 2018 9:09 pm
Lovely, lovely - at this rate you will take the Sunday evening not paying attention to what the wife is watching welding porn award.
It’s all part of my cunning plan Chris. I figure if I put up enough photos of clumsy welding, a certain Bedfordian resident will come out of his (probably expertly self constructed) cocoon and show us all how it should be done.

Glad you are enjoying the pics though - it’s been a funny old couple of weeks for trying to get work done.. I need to give it a full day uninterrupted to really kick things off.

Andy

chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Sun Oct 21, 2018 9:42 pm

Ah the fabled full day to do what you want...

Well maybe tomorrow I’ll find out why the speedo is stuck at 36mph!
2A - 39 FG 70

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Mon Oct 22, 2018 9:50 am

chipbury wrote: ↑
Sun Oct 21, 2018 9:42 pm
Ah the fabled full day to do what you want...

Well maybe tomorrow I’ll find out why the speedo is stuck at 36mph!
Is that the Lightweight equivalent of the Delorean's 88mph time travel velocity? "Where we're going, we don't need roads" etc

Treehugger

Re: Monty the rather rusty 2A - 37FG31

Post by Treehugger » Mon Oct 22, 2018 11:36 pm

andrewjsimpson1977 wrote: ↑
Mon Oct 22, 2018 9:50 am
chipbury wrote: ↑
Sun Oct 21, 2018 9:42 pm
Ah the fabled full day to do what you want...

Well maybe tomorrow I’ll find out why the speedo is stuck at 36mph!
Is that the Lightweight equivalent of the Delorean's 88mph time travel velocity? "Where we're going, we don't need roads" etc
I think you would have a bit of trouble running a LWT on dustbin scraps though.

Matt's landy
Posts: 28
Joined: Sun Jun 17, 2018 8:22 pm

Re: Monty the rather rusty 2A - 37FG31

Post by Matt's landy » Wed Oct 24, 2018 6:35 pm

I'm not picking because it's all about practice, I should say you've got your wire speed too fast and clean the metal around the drilled hole so it arcs up cleaner, both will help you to keep the torch steadier, if you practice on a similar thickness steel and it blows through when wire slowed down then turn the power down a bit, once you've cracked it , it will save a lot of time cleaning up afterwards which will make up for the time practicing, hope that helps

Matt

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Wed Oct 24, 2018 8:01 pm

Thanks for the comment Matt, always welcome.

In fact the wire speed is on the slowest possible setting, and the power is fully down too. The metal was cleaned up with a grinder after drilling. Its really down to the fluxed cored wire I think. I will get some more gas in soon.

Andy

Matt's landy
Posts: 28
Joined: Sun Jun 17, 2018 8:22 pm

Re: Monty the rather rusty 2A - 37FG31

Post by Matt's landy » Wed Oct 24, 2018 9:23 pm

Nice to see the progress as it goes back to original, mine
(37FG35) had been seriously molested before I had it although what was there was good so I built it up as a toy and just retained as much 2a as I could, my main aim to save it from the garage it had been in for 20 years plus in pieces, I have a copy of the microfiche build dates from land rover , chassis numbers 481-505 if yours falls into those, happy to email you a photo of it to put with yours if your interested

Matt

Post Reply